Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5819910.

This is a cap for the Z Axis to plug in a aluminium plate or a sensor.

Here are an example plug that i used: 
https://de.aliexpress.com/item/4000097123821.html

DC-Hohlstecker-Buchse 5,5 x 2,5 mm/zweipoliger Terminal-Block

It should be a tight fit but a lottle bit glue helps.

MPCNC cap with plug

Endkappe_Z_v3.step

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5819854.

This hold your xTool and u can use the raiser if u want to use a rotary.

xTool D1 + Pro Holder and Raiser

Xtools_Halter.step

40mm_Raiser.stl

This is a new K40 Gantry. It can be used for stock K40 or bigger K40 without electric's on the right sided.

For more Informations about K40 Lasers and the Gantry you can visit http://k40.tech and join the Discord Community.

K40 Gantry

K40 Gantry Step File

Endstop Schutz X + Y.3mf

Endstophalter X.3mf

Endstophalter Y.3mf

Halter Aluwelle rechts.3mf

Halter X Achse links.3mf

Halter X Achse rechts.3mf

Idlerhalter VL M3.3mf

Idlerhalter VR M3.3mf

Kopfhalter V2.3mf

Motorhalter Y.3mf

Riemenhalter.3mf

Schild_links Trägerplatte.3mf

Schild_rechts Trägerplatte.3mf

Schleppkettenhalter kurze Version  V1.3mf

Schleppkettenhalter lange Version  V2.3mf

Schleppkettenhalter Laserkopf  V2.3mf

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4497711.

Auf dem Bild ist der alte große Deckel zu sehen da ich den neuen noch nicht gedruckt habe. Dieser unterscheidet sich aber nur im Text oben drauf. Das WW wurde in CW geändert.

# Fusion 360 Links

Kleine Version: https://a360.co/2YXOny6
Große Version: https://a360.co/2Vc1avG

# Controller Case for FHEM RGBWW Controllers V3

See also FHEM Forum:

https://forum.fhem.de/index.php/topic,69740.msg612566.html



# V3 Case

Unten kann man die Kabel einzeln rausführen. Reset Button ist zusammengebaut erreichbar. Deckel wird einfach reingeklickt. Keine Schrauben benötigt.

Controller muss ggf. nachgearbeitet werden. Dazu die Seiten einfach mit Schleifpapier abschleifen bis der Controller in das Case passt.

Bei der kleinen Version muss ebenfalls nachgearbeitet werden und zusätzlich rundherum das PCB zum wegbrechen entfernt werden.

# Hutschienenhalter
Der Hutschienenhalter wird mit ganz wenig Support gedruckt. Der Support sollte beim ersten bewegen rausfallen.

RGBWW Controller Case v3

RGBWW_Controller_kleine_Version_v8.step

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5651047.

Print without support and with your choosen infill.
Walls 2-3.
Recommendet material: PETG

For easy alignment of a MGN12H Linearrail with aluminium extrusion profiles.

Linearrail Alignment for Aluminium Profiles 20x20 20x40

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4912488.

DE

(Happy) Filament Spulen Abroller.
(Happy, weil der Abstandshalter ein einen Smiley ähnelt.)

Materialliste:
4x 608er Kugellager
4x M2,5-3x8-16 Schrauben

Nach dem Drucken die Lager in die Rollen bis Anschlag einpressen und zusammenbauen.

Aktuellste Version unter folgendem Link Online als 3D Modell zu betrachten: https://a360.co/3ivj1sB


EN

(Happy) Filament Spool Dispenser.
(Happy because the spacer resembles a smiley face.)

Material:
4x 608 Bearing
4x M2,5-3x8-16 Screws

After printing, press the bearings into the rollers as far as they will go and assemble.

The latest version can be viewed online as a 3D model under the following link: https://a360.co/3ivj1sB

V1 - First release.

(Happy) Spool Holder

Rolle.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3678828.

# old Version - see new Designs!

# Controller Case for FHEM RGBWW Controllers V2

See also FHEM Forum:
https://forum.fhem.de/index.php/topic,69740.msg612566.html



# V1 Case

  - Holes for Wires and Screw Terminals
  - Wiring Info on Top
  - Click open/close - no Screws needed

RGBWW Controller Case - old Version

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5696277.

Mainbody need support.

Use Fusion Archive File for edit for your needs

Thread Insert Tool

Lötkolbenhalter v21.step

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5651190.

This is a Model of the new Cloudray Typ K 4060 V2 Laserhead.

Cloudray Typ K 4060 V2

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5653159.

Print with support for better overhang that holding the stripe.
100mm version.
Should work for all standart Stripes.
Designed with 5050 LED Stripe.

This is WIP and not printed yet.

LED 45° Halter - 100mm

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3693337.

# Led Halterung im 45° Winkel

Länge 220mm
Breite 17mm
Höhe 14mm

Der LED Streifen sollte eine Breite von 10mm haben was dem Standard entsprechen sollte.

Jeweils links und rechts sind Löcher zur Befestigung. Dazu den LED Streifen einfach verschieben.

An den Außenkanten sind Halbkreise damit das Kabel nach hinten geführt werden kann.

# V2 mit größerem Loch für die Schraube in der Schräge.

# V3 mit anderer Befestigung und etwas kürzer (200mm) sollte nun besser mit den LED Streifen passen


LED Holder 45°

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5650804.

For easy unscrew the mirror nut.

Spiegelhelfer

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5651228.

This is a simple model of a K40 MYJG-40W powersupply.
The model is not true to size, it is for demonstration purposes only.

K40 Powersupply

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

vr6syncro

Achievements

Seedling

Debutant