A simple charging base for the 5th gen Ipod Classic (model A1136) that uses a 2 piece friction fit clamp to hold the cable in as the Ipod is inserted in and out. I have been using this for well over a year and it still has yet to loosen up even a little. Once you print off all three pieces the two smaller clamp pieces just go around the charging cable, no glue or anything is needed to hold it on, just hold it together with your fingers and line it up with the bottom of the base and press into the base, both halves should be fairly tight. The cable clamp only goes in one way so make sure you line it up as well as the charging cable itself before pressing in. Once it is pressed in check to see if it moves by inserting your ipod and if it does adding a little bit of hot glue on the underside should help, then just route the cable through the channel on the underside of the base and add some rubber feet if you like. Happy Printing!

Ipod Classic (5th Gen) Charging Base

Ipod Classic 5th Gen Base.stl

A keychain accessory in the shape of a SNES controller, it comes quite large but you can scale it to any size you like, just be aware that anything below 40% size may be too small to attach a keyring. I would also recommend not changing the Z height to be any thinner than it is, just scale your x and y so it is thick enough to not bend and break. Happy Printing!

SNES Controller Keychain

Keychain SNES Controller 1.stl

A set of bins made for smaller solderless breadboards, of which the standard sizes for them are usually around 54-56.5mm wide, around 82mm long and 9mm thick. If your breadboard is that size or smaller it should fit just fine as most breadboards follow the same standard sizes. There are 3 bins included with one that has text on the side, one with text on the front and one with text on three sides, so no labels are even needed. Happy Printing!

Gridfinity Breadboard Bins 2x1

Gridfinity 2x1 Breadboard Bin Front Text.stl

This is a Gridfinity compatible 2x2x12 set of bins that just like my quad, penta and hex windowed models this one uses microscope slides all around so you can easily see from any side what is in the bin. There is a model with a spot above each slide for a standard 0.5"/12mm label, and one without the labels. Happy Printing!

Gridfinity Octa Windowed Bins 2x2x12

Gridfinity 2x2x12 Octa Windowed.stl

This is a pair of Gridfinity compatible bins that fit Ryobi 4V batteries, one is short if you do not plan on stacking and the other is tall to allow for stacking them. Happy Printing!

Gridfinity Ryobi 4V Battery Bins

Gridfinity 1x1 Ryobi 4V Bin.stl

This is basically the same thing as my 1x1x12 quad window bin, however i have added a center diagonal divider to make it a 2 compartment bin. The center piece has a slight recess that allows the microscope slide to go into the base plate so there is no gaps at the bottom between the slide and the base plate. There are two versions, one with room at the top for standard 0.5"/12mm labels and one without. All you need is about 30 grams of pla and 5 microscope slides. Happy Printing!

Gridfinity Penta Windowed Bin 2 Compartment 1x1x12

This is basically the same thing as my 1x1x12 Quad window bin, however i have added a center diagonal divider to make it a 2 compartment bin. The center piece has a slight recess that allows the microscope slide to go into the base plate so there is no gaps at the bottom between the slide and the base plate. There are two versions, one with room at the top for standard 0.5"/12mm labels and one without. Happy Printing!

Gridfinity 1x1x12 Penta Windowed Divided Bin.stl

A Gridfinity compatible 2x2 holder for Milwaukee batteries that even lets the batteries lock into the model. If you use the standard 6mmx2mm magnets in the holes provided they should be strong enough to hold this in place on the base plate while the battery slides out, provided that you push the release buttons on the battery all the way in as you take it off. There is an overhang towards the top of the model that not all filaments will handle well, with PLA it did bridge okay for me and a hobby knife makes short work of any small drooping pieces.  Happy Printing! 

Gridfinity Milwaukee Battery Holder 2x2

I needed something to hold a couple of grocery bags as I use them as trash bags in my smaller trash cans, so I came up with this. Compatible with the gridfinity system and fits in a 2x2 slot, to load bags simply push some bags through the hole in the back one at a time and use your finger to push each bag as high as it will go. Happy Printing!

Gridfinity Grocery Bag Dispenser Bin 2x2

This is a 3x1 Gridfinity compatible enclosure for the DSO138 oscilloscope. It comes with two covers with one that has text and another without, the only three non 3d printed things this requires are the DSO138 itself, 4x M3x20mm bolts, and 4 M3x5mm diameter threaded inserts that are either 4 or 5mm long. You will need to use a soldering iron to press these 4 inserts into the holes on the base. You will also have to modify the screen pcb slightly by using a pair of nippers to cut the tips of all the pins on the upper display board so the display will sit flush with the cover. Then press on all three of the switch covers on the switches and make sure they are as flush with the switch housing as you can get them so they will not wobble on the switch stem. After that turn the cover upside down, put in all the button covers and press the main pcb against the cover and button covers tightly. Hold the pcb tight against the cover while you screw the cover into the base plate, if you hold it tight the button covers should not move. Once screwed together check all buttons and switches are working correctly. Happy printing!

Gridfinity DSO138 Enclosure 3x1

Gridfinity DSO138 1x3 Base.stl

Much like my 1x1 quad window model this is also pretty much all glass. It helps get rid of the extra microscope slides you have lying around while looking great and letting you see from any side what is stored in your bins. Happy Printing!

6/12/23 Update- A second model has been added that adds labels to the sides of the bin much like my quad and penta window bin models.

Gridfinity 6 Windowed 1x1x12 Bin (Updated)

Much like my 1x1 quad window model this is also pretty much all glass. It helps get rid of the extra microscope slides you have lying around while looking great and letting you see from any side what is stored in your bins. Happy Printing!

Gridfinity 6 Windowed 1x1x12 Bin

Gridfinity 1x2x12 Hex Windowed With Labels.stl

You know all those microscope slides you bought for all your gridfinity bins? Well if you are like me you have way too many of them just laying around taking up space on your desk. Well it's time to use them up and that is where this comes in handy as it uses 4 slides and hardly any filament at all. The end result is a tall bin that lets you see whatever you put in it no matter what orientation you put it in on the baseplate all while looking absolutely fantastic. Check out my 2x1 version as well and if there is enough interest I'll be happy to make a 2x2 as well. Happy Printing!

Update 6/7/23- Includes a version with 4 label slots at the top of the model, compatible with standard 0.5"/12mm labels.

Gridfinity Quad Window Bin 1x1x12

You know all those microscope slides you bought for all your gridfinity bins? Well if you are like me you have way too many of them just laying around taking up space on your desk. Well it's time to use them up and that is where this comes in handy as it uses 4 slides and hardly any filament at all. The end result is a tall bin that lets you see whatever you put in it no matter what orientation you put it in on the baseplate all while looking absolutely fantastic. Check out my 2x1 version as well and if there is enough interest I'll be happy to make a 2x2 as well. Happy Printing!

Gridfinity 1x1x12 Quad Windowed With Labels.stl

This is a gridfinity compatible spring loaded component holder. It comes with two arm versions, one with a printed head on it and the other with a hole to thread an M3 bolt in.  For the hinge an M3x12mm bolt is used although a longer one can be used as well, in order to ensure the hinge is smooth you can drill one side of the base (not both, one side the bolt has to be able to thread into) and the arm hole with a 3mm bit. As for the spring anything within the following parameters will work, spring strength is mostly based on user preference. Spring ID should be at least 3mm, the OD no more than 10mm and the length at minimum 25mm. Happy Printing!

Gridfinity SMD/Component Handy Holder

Gridfinity 2x1 SMD Handy Holder Base.stl

This is an gridfinity compatible enclosure for the LCR-T4 component testers that you often find on Amazon or Ebay, it is a rather cheap piece of hardware that tends to be handy for identifying transistors and other components. You can either use threaded inserts and just drill the holes in the base a little larger to set the threaded inserts or you can thread the holes directly with 4 M3x16mm screws. I also made this to accept a dc barrel jack in the bottom of the base which is linked below, if you decide to use this enclosure you will need to cut off the 9v battery adapter if your model has one and solder directly to the barrel jack. Once you have done that just place the pcb over the holes on the base, line up the face plate and put in the screws in the front plate and tighten. Happy Printing! 

Link to dc barrel jacks used-
https://www.amazon.com/gp/product/B091PS6XQ4/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

Gridfinity LCR-T4 2x1 Enclosure

Gridfinity 2x1 LCR-T4 Base.stl

This is a Gridfinity 2x1 compatible bin that holds a variety of 3D printer accessories such as 2 nozzle wrenches, 2 tweezers, 2 wire brushes, nozzle cleaning needles, and 5 sizes of allen wrenches from M2 to M6. Cheap accessory kits like the one in the model pic can be found on amazon, here is the one I used. https://www.amazon.com/dp/B0BPNMV6ZY?psc=1&ref=ppx_yo2ov_dt_b_product_details
In case you already have a kit and are wondering if yours will fit the sizes of the part cutouts are as follows, 12mm diameter for cleaning needle tubes, 13mmx19mm for the wire brushes, 11mmx3mm for tweezers, and 11x2 for the nozzle wrenches. Happy Printing!

Gridfinity 3D Printer Accessories 2x1 Bin

This is a collection of Gridfinity compatible bins that hold all of your tiny CR style lithium cells. I have a variety of sizes so far and am currently making more. In the future I will add some mixed ones that can hold multiple types of button cells at once. Happy Printing!

Gridfinity CRXXXX Battery Bin Collection

Gridfinity 1x1x2 CR927 x21 Battery Bin.stl

A handy little set of solder fingers that rest in a 2x1 Gridfinity slot. It has a large variety of slits that allow wires up to 4.5mm in diameter to be placed in it. Happy Printing!

Gridfinity Solder Fingers 2x1

Holds three 25mm diameter glue sticks and fits in a 2x1 grid slot. Happy printing!

Gridfinity X3 25mm Glue Stick Holder.stl

Made to be used with the Gridfinity system, takes up a 2x1 slot and fits 45 4mm bits. Instead of the normal hexagonal cutouts for the bits this uses 4.5mm holes to make it easier for lower quality prints to fit your bits and allow them to slide in and out easily without excessive sanding or feeling like you are press fitting your bits into your print. With this it is much simpler, if the hole is too tight just ream it out with a 4.5mm drill bit and you're done. Happy Printing!

Gridfinity 4mm Bit Holder 

Do you want to store all your wall adapter chargers on a handy modular storage system? Well this has you covered, it now holds 1, 2 or 3 wall chargers and fits in a 2x1 gridfinity space. Happy Printing!

Gridfinity 2x1 Wall Charger Tower (Updated)

Do you want to store all your wall adapter chargers on a handy modular storage system? Well this has you covered, it holds 3 wall chargers and fits in a 2x1 gridfinity space.

Gridfinity 2x1 Wall Charger Tower

Gridfinity 2x1 Wall Adapter Tower 1 High.stl

Gridfinity 2x1 Wall Adapter Tower 2 High.stl

This is a holder for Hard hats that either zip ties, glues or velcros to your hard hat to allow you to store a normal sized sharpie and a carpenters pencil. Both the pencil and sharpie can be slid in or popped into place, to pop the pencil into place stick the side closest to the sharpie in first then twist the top of the pencil towards the holder to lock in the pencil. 

Hard Hat Sharpie and Pencil Holder

A handy little base for your Miniware MHP30 hot plate that makes it compatible with the Gridfinity system while still allowing access to both buttons and the power port and making it more stable than before. Requires no supports and holds the hot plate in via a single M3x5mm screw on the bottom, also works with button or socket head screws. Fits in a 2x1 Gridfinity slot.

Gridfinity MHP30 Base 2x1

Just a young Engineer who like to make things in my free time. Now that gridfinity is around it looks like i'll be making stuff to organize literally everything, thanks Zach Freedman.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Landrum Engineering

Pinned models

Gridfinity 2x1 Wall Charger Tower (Updated)

Gridfinity Quad Window Bin 1x1x12

Gridfinity Milwaukee Battery Holder 2x2

Ipod Classic (5th Gen) Charging Base

SNES Controller Keychain

Gridfinity Breadboard Bins 2x1

Gridfinity Octa Windowed Bins 2x2x12

Gridfinity Ryobi 4V Battery Bins

Gridfinity Penta Windowed Bin 2 Compartment 1x1x12

Gridfinity Milwaukee Battery Holder 2x2

Gridfinity Grocery Bag Dispenser Bin 2x2

Gridfinity DSO138 Enclosure 3x1

Gridfinity 6 Windowed 1x1x12 Bin (Updated)

Gridfinity Quad Window Bin 1x1x12

Gridfinity SMD/Component Handy Holder

Gridfinity LCR-T4 2x1 Enclosure

Gridfinity 3D Printer Accessories 2x1 Bin

Gridfinity CRXXXX Battery Bin Collection

Gridfinity Solder Fingers 2x1

Gridfinity X3 25mm Glue Stick Holder.stl

Gridfinity 4mm Bit Holder

Gridfinity 2x1 Wall Charger Tower (Updated)

Hard Hat Sharpie and Pencil Holder

Gridfinity MHP30 Base 2x1