Modular SMD Storage Plates - Stackable

WenTaiBoxPlate.stl

Soldering Fume Extractor

FumeExtractor1.3mf

Dewalt Soldering Station

Dewalt Soldering Station Top.stl

Magnetic PCB/Circuit Board Clamp

PCB Clamp Base.stl

Gridfinity bin for pinecil and included tip

PinecilGridfinity-Magnets.stl

Multiboard Soldering Iron Holder

Multiboard Soldering Iron Holder.step

FNIRSI HS-01 Soldering Iron Case with Electric Screwdriver

case1.stl

TS100 Soldering Station Setup

Station de soudage.3mf

Modular Filter Box for 120mm fan - laser engraver, soldering etc.

Charcoal Filter Insert.stl

Soldering Base Only

solder plate final.stl

Gridfinity MG Chemicals.step

Gridfinity Solder Holder Station - Refined

Gridfinity Solder Holder Base

Hakko Soldering Station Multiboard Multiconnect

Hakko Side Mount Multiconnect.stl

GridFinityPinHeaderSolderingAid.stl

simple 80mm Soldering Fume Extractor

top part.stl

T18 tip station

T18 tip station v6.stl

Pinecil Soldering Iron Carry Case and Portable Solder Station

Pinecil Carry Case - Bottom Half.stl

Gridfinity 1x1x6 Chipquik flux pen holder.stl

This model is a holder for a Chipquik flux pen, on Zack Freedman's Gridfinity organization system. It is on a 1x1 base, and is 5 units in height.
This could be considered overkill for one pen, but I am eternally setting my flux pen down and losing track of it. I printed it in Cherry Blossom Silk PLA, but any old filament should do. No supports necessary.

Soldering wire stand (Print in place)

Really proud of this one. Soldering wire stand with print in place hinge and metal shaft slid into a hole. supports most sizes of soldering wire spools, many spools can be installed at once. If you want to access the spools, just lift the metal shaft up. If a small wire spool is installed, there is always more room for insulation tape, scotch tape etc
it works incredibly smoothly and is very strong. the bottom of the stand is corrugated so it grips nicely to a rough desk but there are also round holes for rubber pads.
The middle section has all the main lead exposure health hazards noted down for when you'll inevitably forget about them from all the lead fumes you have been inhaling. The sides have tin and lead elements decals.

_The model is supposed to be printed laying down with the hinge's shaft touching the build plate. The orientation here is very important so that the hinge works properly. I printed mine with .6mm nozzle at .14mm layer height and 10% infill. it's very strong and the letters & decals and perfectly readable. No brim and only one support for the shaft slot on the left side.
After printing, a ~10cm long, 10mm wide shaft is supposed to be pushed into the hole above the hinge. If you dont have a metal shaft, you can always 3d print one though it wont look as neat._

Gridfinity Flux Holder v2.stl

V2 of my soldering flux holder for standard sized cans of flux. It fits the Gridfinity grid.
V1 isn't online yet but I will upload it if you guys want it. It's the same as V2 but with a smaller diameter for those small cans.

Soldering

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Modular SMD Storage Plates - Stackable

Soldering Fume Extractor

Dewalt Soldering Station

Magnetic PCB/Circuit Board Clamp

Gridfinity bin for pinecil and included tip

Multiboard Soldering Iron Holder

FNIRSI HS-01 Soldering Iron Case with Electric Screwdriver

TS100 Soldering Station Setup

Modular Filter Box for 120mm fan - laser engraver, soldering etc.

Soldering Base Only

Gridfinity MG Chemicals.step

Gridfinity Solder Holder Station - Refined

Hakko Soldering Station Multiboard Multiconnect

GridFinityPinHeaderSolderingAid.stl

simple 80mm Soldering Fume Extractor

T18 tip station

Pinecil Soldering Iron Carry Case and Portable Solder Station

Gridfinity 1x1x6 Chipquik flux pen holder.stl

Soldering wire stand (Print in place)

Gridfinity Flux Holder v2.stl