Straighten out your workshop with Gridfinity modular storage - deploy these plates anywhere you need some order!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Frame: https://a360.co/3ccHbsg
- Weighted Plate: https://a360.co/3uCJ2gR

The foundation of every Gridfinity setup is a baseplate, and these let you drop storage where you need it most.

**Frame**: The absolutely minimal no-frills baseplate. No room for screws or magnets, but saves filament and headroom. If your storage unit is on a steel surface, you can still put magnets in the storage blocks to keep them from sliding.

**Weighted**: Heavy, sturdy baseplate perfect for desktops, shelves, and other places where knocking stuff over is a big problem. 

Secure blocks permanently with [M3 screws,](https://amzn.to/37IaXTg) or temporarily with [6x2mm magnets](https://amzn.to/37Ihopq). Add [rubber feet](https://amzn.to/3LZv4v5) to keep the whole shebang from sliding, and [metal tire weights ](https://amzn.to/3uAzH9f)to drop the center of gravity and prevent wipeouts. You don't need to install every magnet, foot, and weight! Just use enough for your needs.

A Prusa i3 Mk3 can print up to a 5x5 grid. No matter what you use, make sure your bed adhesion and release is dialed in - these love to curl, and their high surface area can make them challenging to remove.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider plates can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Baseplates

Weighted Baseplate 3x2.stl

Frame 1x4.stl

Frame 1x5.stl

Frame 1x6.stl

Frame 1x7.stl

Frame 2x2.stl

Frame 2x3.stl

Frame 1x2.stl

Frame 1x3.stl

Frame 2x7.stl

Frame 3x3.stl

Frame 3x4.stl

Frame 3x5.stl

Frame 3x6.stl

Frame 3x7.stl

Frame 4x4.stl

Frame 4x5.stl

Frame 4x6.stl

Frame 4x7.stl

Frame 5x5.stl

Frame 5x6.stl

Frame 5x7.stl

Frame 6x6.stl

Frame 6x7.stl

Frame 2x5.stl

Frame 2x6.stl

Weighted Baseplate 1x3.stl

Weighted Baseplate 1x4.stl

Weighted Baseplate 1x5.stl

Weighted Baseplate 1x6.stl

Weighted Baseplate 1x7.stl

Weighted Baseplate 2x2.stl

Weighted Baseplate 1x1 (super cute).stl

Weighted Baseplate 1x2.stl

Weighted Baseplate 2x4.stl

Weighted Baseplate 2x5.stl

Weighted Baseplate 3x6.stl

Weighted Baseplate 3x7.stl

Weighted Baseplate 4x4.stl

Weighted Baseplate 4x5.stl

Weighted Baseplate 4x6.stl

Weighted Baseplate 4x7.stl

Weighted Baseplate 5x5.stl

Weighted Baseplate 5x6.stl

Weighted Baseplate 5x7.stl

Weighted Baseplate 6x6.stl

Weighted Baseplate 6x7.stl

Weighted Baseplate 7x7.stl

Weighted Baseplate 2x7.stl

Weighted Baseplate 3x3.stl

Weighted Baseplate 3x4.stl

Weighted Baseplate 3x5.stl

Get the new Extra Fast Cura Profile from Filament Friday. This Filament Friday Extruder top 3D print is just a fun example for using the new Filament Friday Extra Fast Cura Profile that is part of the .3mf file. This print took 37 minutes with the CHEP4.12_ 0.28(Rough) profile. The FF_0.28(Extra-Fast) Profile only took 23 minutes on Ender 3 Pro.
Just download this, unzip the files and then load the .3mf project file. When the project loads it will automatically add it to Cura for you to use.

Filament Friday Extra Fast Cura Profile

FFExtruderTop_ExtraFastProfile.3mf

Versatile open-top storage blocks for the Gridfinity modular workshop storage system - multiple sizes for infinite options!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at  
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source file: https://a360.co/3vbu9B5

These are perfect for storing small parts and long, thin objects like needle files, and you can stack them as high as you want! The inner surface has a generous scoop to make retrieving parts easy, and the tab fits 12mm label-maker tape.

I've provided a selection of different sizes and divider counts, to give you OPTIONS! Note that none of the compartment sizes overlap - there isn't a two-compartment 4x1 bin because you can just use two one-compartment 2x1 bins.

Dimensions in file names are Width x Depth x Height. Width and Depth units are 42mm grid slots, Height is in 7mm units. A Prusa i3 Mk3S can fit a five-unit-wide bin on its plate.

Note that two-unit-high bins don't have labels - they would cut too far into the usable storage area.

Brims and support are not required, and these can be printed in any filament with an 0.6mm or smaller nozzle. Wider bins can curl, so maximize your bed adhesion if you're going big!

**Gridfinity Tips!**
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Divider Bins

Divider Box 2x1x6 5-Compartment.stl

3D printing accessories for the Gridfinity modular workshop system - store tools, nozzles, and more!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Caddy: https://a360.co/3KzVx2a
- Bottle Holder: https://a360.co/3LVjAsC
- Magigoo Holder: https://a360.co/3KzVEe6
- Nozzle Holder: https://a360.co/3KxGS7y
- Volcano Nozzle Holder: https://a360.co/3JLhKJz
- Revo Nozzlebreak Holder: https://a360.co/3xmVPpk
- Glue Sticc Holder: https://a360.co/3vapCiq

This assortment of 3D printer organizers is perfect for printing what you love to print - accessories for your printer!

**3D Printer Caddy**: Puts emergency supplies within reach! Holds scraper, nippers, tweezers, acupuncture needles, brass brush, adjustable wrench, and nozzle wrench

**Bottle Holder**: Designed to hold Nano Polymer high-temperature bed treatment, but also fits many small spray bottles. Bottles should not shake loose.

**Dual Bulk Nozzle Holder**: Holds eight copies of two different nozzle sizes. Can stack when loaded with E3D or Creality-style nozzles.

**Quad Revo Holder**: Holds four E3D RapidChange Revo nozzle-heatbreak nozzlebreaks. Can stack.

**Triple Volcano Holder**: Holds three extended E3D-style holders, like those included with the Anycubic Vyper and Kobra. Can stack.

**Glue Stick Holder**: Holds multiple sizes of icky sticky horsey bois, particularly Elmer's small and regular, and Kores.

**Magigoo Holder**: Holds four-piece Magigoo bed treatment assortment pack, and should not allow them to jiggle loose.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity 3D Printing Bundle for Nerds

3D Printer Caddy.stl

Pen, pencil, and marker storage blocks for the Gridfinity modular workshop storage system - multiple options to fit your machine shop!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Regular Version: https://a360.co/37EP2we
- Chisel Version: https://a360.co/3E49liU
- EXTRA THICCCCCC: https://a360.co/3jqmzx4

These holders were designed to securely store Sharpie markers, but should fit many other brands of markers and other roughly marker-shaped objects. I won't judge, you do you.

These are tall enough to keep the pens from falling out, but securing with magnets or screws is **strongly** recommended!

**Regular version**: Fits standard Sharpie markers and other round, slim objects with a diameter of 12mm or less, like brushes and test tubes.

**Chisel version**: Fits chisel-tip Sharpies, paint pens, and other stuff with a cross-section that fits a 16x22mm ellipse.

**Magnum version**: Fits the girthiest of Sharpies and other extra-thicc 27mm rods. Careful where you point that thing.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Pen, Pencil, and Marker Holders

Sharpie Holder, Chisel.stl

This includes a .stl and my FF_Good_0.2(PETG).curaprofile as part of the .zip download.

Filament Friday PETG Good 0.20 Cura Profile

This includes a .stl and my FF_EF_0.20(PETG).curaprofile as part of the .zip download.

Glass-front open-top storage blocks for the Gridfinity modular workshop storage system - yes, real glass!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at  
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source file: 
https://a360.co/3v8mtzG

These modified divider bins have one wall replaced with a glass microscope slide! Glass is more scratch-resistant than acrylic, and microscope slides come pre-cut to size. 

Each bin is made of two parts, the Compartment and the Faceplate. You'll also need:
- 1x3" Microscope slides: https://amzn.to/3O6qjBO
- 2mm Repair Tape: https://amzn.to/3M1D9zF

How to assemble:
1. Apply two strips of tape to the microscope slides, touching the short edges.
2. Stick that slide to the faceplate.
3. Apply two strips of tape down the short sides of the faceplate, over the glass.
4. Apply a third strip along the bottom. It will curl a little around the bottom.
5. Slap that crap onto the divider bins. Press hard.

These are perfect for storing small parts, especially if you plan to stack 'em up. The big window makes it easy to check what's inside and monitor your supply levels.

The inner surface has a generous scoop to make retrieving parts easy, and the tab fits 12mm label-maker tape.

I've provided a selection of different divider counts, to give you OPTIONS! Because microscope slides are only available in one size, only 2-unit-wide bins are possible.

Brims and support are not required, and these can be printed in any filament with an 0.6mm or smaller nozzle. 

**Gridfinity Tips!**
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Window Divider Bin

Window Box 2x1x6 3-Compartment.stl

This includes a .stl and my FF_Best_0.12(PETG).curaprofile as part of the .zip download.

Filament Friday PETG Best 0.12 Cura Profile

Filament Friday PETG Extra Fast 0.20 Cura Profile

This file download includes a 06 Nozzle Profile for Cura 5.2.1 and later. It can print very Good quality small prints. 
More details in the video: https://youtu.be/c6w1tkP9RxY

Filament Friday 06 Nozzle Good Profile

This includes a .stl and my FFV5.1_EF(0.12).curaprofile as part of the .zip download so you can just load the profile into Cura instead of a .3mf.

Filament Friday Extra Fast (0.12) Cura Profile

This includes a .stl and my FF_EF_0.28(PETG).curaprofile as part of the .zip download.

Filament Friday PETG Extra Fast 0.28 Cura Profile

Filament Friday PETG EF 0.28 Cura Profile

__3D printed filament dry box__


An enclosure for one spool of filament featuring desiccant cages and hygrometer for reducing and monitoring moisture on hygroscopic filament. Rewind system with locking mechanism for when the spool is not in use. Check out [the videos](https://www.youtube.com/watch?v=rsfHs_I52mk&list=LLMvNnP9oAQl5IApL8XBQIkQ)!

Make sure to check the advantages and disadvantages first, and follow instructions on [the project page](https://mihaidesigns.com/drybox/).

__Printing:__
>* Print one base (filename starting with "print one base.")
>* Print one lid (filename starting with "print one lid.")
>* Print all 40 shared files (some are identical)


DXF files included for laser cutting windows.


See the [BOM list](https://docs.google.com/spreadsheets/d/1ia3ImaCrxpdLvES7OI8j2lGvnmtfEvpncn1Ds7_c1f0/edit#gid=0) for required parts.

Licensed under CC https://creativecommons.org/licenses/by-nc-sa/4.0/


If you like my projects, you can support my work on [Patreon](https://www.patreon.com/mihaidesigns)! 😎

No supports needed, supportless, FDM.

Mihai's DryBox

pick one base. front and side angled windows (default).stl

front_panel.dxf

side_panel.dxf

Mount storage right to your printer with the Gridfinity modular workshop storage system - whatever machine you use!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Anycubic Sidecar: https://a360.co/3xonYw4
- Anycubic Top: https://a360.co/3jy22GN
- Lulzbot: https://a360.co/3xobNzx
- Prusa: https://a360.co/3Jzfp47
- Snapmaker: https://a360.co/37Om65m
- E3D Toolchanger: https://a360.co/3rlmn6K

These brackets mount to your 3D printer and allow you to put Gridfinity storage blocks right where you need them! These work especially well for the [Gridfinity 3D-printer accessory kit](https://bit.ly/3jtTfWu).

If you need more adjacent slots, just print multiple baseplates and butt them up against each other. *I STRONGLY recommend magnets or screws so you don't knock stuff into your printer!*

**Anycubic Vyper/Kobra**: Also fits any printer made of extrusion with 6mm slots. Mount to your printer's frame with [M5 hammer nuts for 6mm slots](https://amzn.to/3jzbOZb) and [M5x12mm countersunk screws](https://amzn.to/3xoGLHV). Remember to measure countersunk screws from the TOP OF THE HEAD!

The **sidecar** baseplate mounts to the base frame, parallel with the floor, a lot like the included filament holder. The **top-mount** baseplate mounts on the Z axis crossbeam or base frame. *Make sure the gantry, extruder, and plate don't collide with your Gridfinity!*

**Lulzbot**: Fits the upward-facing edges of the top crossbars. This one is a real pain in the butt to install.

**Prusa**: Slides on over the steel frame, no fasteners required. *THE BASEPLATE AND EXTRUDER MUST BE ON OPPOSITE SIDES OF THE FRAME!*

**Snapmaker**: Mount to the optional enclosure with [M5 hammer nuts for 6mm slots](https://amzn.to/3jzbOZb) and [M5x12mm countersunk screws](https://amzn.to/3xoGLHV). Remember to measure countersunk screws from the TOP OF THE HEAD! I didn't make one for the printer itself, sorry!

**Toolchanger**: Mount to the top of the printer with three button head M3x5 screws. *Don't use longer screws! They won't fit!*

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Printer-Mounted Baseplates

Anycubic Baseplate, Sidecar.stl

This includes a .stl and my FF_EF_0.12(PETG).curaprofile as part of the .zip download.

Filament Friday PETG Extra Fast 0.12 Cura Profile

CNC bit storage blocks for the Gridfinity modular workshop storage system - multiple options to fit your machine shop!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Jewel Case: https://a360.co/3Jw4Bnd
- Bulk Holder: https://a360.co/37IQCgV
- Tubes: https://a360.co/3rFWH4X

These holders securely store CNC tools, drill bits, and other things with 1/8", 1/4", and 3mm shanks.

The 1/8" and 1/4" Bulk versions hold up to 77 and 21 bits, respectively. These point the bits straight up, so you can't stack on top! Be careful not to hurt yourself!

The Tube version holds 12 bits in their protective packages. You can stack other blocks on top of this.

The Jewel Insert version holds four detachable sleeves from snap-together jewel case packaging. These usually hold 10 bits. You can stack other blocks on top of this.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity CNC Tool Holders

CNC Tool Holder, Tubes.stl

This includes a .stl and my FFV5.1_EF06NOZ(0.44).curaprofile as part of the .zip download so you can just load the profile into Cura instead of a .3mf.

Filament Friday Extra Fast 0.6 Nozzle Cura Profile

V5.1-ExtraFast-0.44_0.6Nozzle.stl

Helper tool for 3D printer E-steps calibration.

Print either tool (larger one provides more accuracy) and use with [my calibration wizard](https://mihaidesigns.com/esteps/).

[Video on YouTube](https://www.youtube.com/watch?v=8RqS5cAt_GQ).

Tools feature filament marking points and a built in ruler for measuring the error. The larger tool includes adhesion supports that need to be removed before use.

Check my other projects at [mihaidesigns.com](https://mihaidesigns.com/).

Extruder E-steps calibration tool

E-steps calibration tool 100mm.stl

This Filament Friday Extruder top 3D print is just a fun example for using the original Filament Friday Extra Fast Cura Profile that is part of the .3mf file. This print took 37 minutes with the CHEP4.12_ 0.28(Rough) profile. The FF_0.28(Extra-Fast) Profile only took 23 minutes on Ender 3 Pro.
Just download this, unzip the files and then load the .3mf project file. When the project loads it will automatically add it to Cura for you to use.
I've also added the .curaprofile for those who cannot load the .3mf

More details here: https://youtu.be/t_9ADBZVCoA

Extra Fast Cura V4.x Extra Fast Profile 

This is my CHEPCUBE design ready to test with the included Cura V5.4 0.16 Beta profile I just released. Download all to get all the files. Use a Creality Ender 3 Machine profile to load it and adjust the machine settings to match your printer. You can rename the machine profile to eliminate confusion.

Filament Friday Cura V5.4 0.16 profile beta

Office Supplies

Most Popular of All Time

Categories

Popular

Personalize

Trending