Safely grab the right tool with the Gridfinity modular workshop storage system!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at https://www.youtube.com/watch?v=ra_9zU-mnl8
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Nipper Holder: https://a360.co/37jchw3
- Stripper Holder: https://a360.co/3Erq2oV

These racks pack tons of hand tools into a small area, positioned so you can safely see and grab the business ends. These work great for nippers, flush cutters, wire strippers, pliers, scissors, crimpers, nibblers, cutters, and punch-down tools.

*These storage blocks are extra-big and tend to curl! Use a brim and ensure good bed adhesion.* 

**Nipper Holder**: Holds six tools about 80mm from handle to handle. If the tool is spring-loaded, the undercut will keep it from falling out. This can be mounted sideways to store five tools.

**Stripper Holder**: Holds two wire strippers or other long, slim hand tools up to 18mm thicc. I've prepared two sizes - 200mm is your usual multi-hole wire stripper, and 160mm fits many crimpers and termination tools. Both should fit on most printers.

**Gridfinity Tips!**
- Use any filament with an 0.6mm or smaller nozzle. 
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Nippers + Strippers + Pliers Racks

Nipper Holder x6.stl

Socket organizers and ratchet holders for the Gridfinity modular workshop storage system!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- 1/4" Imperial holder: https://a360.co/37cdZPW
- 1/4" Metric holder: https://a360.co/3vgUAFq
- Mulwark ratchet holder: https://a360.co/3OiHhNJ

These holders store your socket sets and ratchet drivers. They orient the tools to make them easier to find and grab the bit you need!

**1/4" Imperial and Metric Holders**: Designed for Harbor Freight 10-piece 1/4"-socket kits, but should fit many others.

**1/4" Universal Holder**: Has ten 20mm-diameter slots. Note that this is five slots wide, while the Imperial and Metric versions are four slots wide.

**Mulwark Holder**: Fits the [Mulwark-brand low-profile ratchet driver](https://amzn.to/3v6BPEw), the 20pc bit kit, and has slots for 13 more hex bits. I strongly recommend buying the bit kit - a low-profile ratchet needs low-profile bits!

Print the ones that work with your stuff!

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners!

Gridfinity Ratchet + Socket Holders

Socket Holder, Metric, Non-Stackable.stl

Socket Holder, 0.25in, Universal, Non-Stackable.stl

2x3x7.4mm Gridfinity Drawers.

Tested in PLA, printed with body cavity facing upwards and with only tiny supports between the gridfinity rows on a Elegoo Neptune 2 model.

Suggest minimal cubic infill (5-10%) with 3-4 outer walls.

 * Added drawer model with thicker walls.
* Refined drawer model for a better fit into the slots horizontally.
* Added two-compartment drawer model.
* Added drawer with a tighter horizontal fit.
* Added double-height drawer model.
* Added Minifinity drawer model.

* Organize your Gridfinity Drawers with Minifinity!
https://social.thangs.com/m/195636

Gridfinity concept by Zack Freedman

Gridfinity Drawers

Gridfinity_Drawers_2x3_Chest.stl

Gridfinity_Drawers_Drawer_Thicker.stl

Gridfinity_Drawers_Drawer_Thicker_Two_Compartment.stl

Gridfinity_Drawers_Drawer_Thicker_Tighter_Fit.stl

Gridfinity_Drawers_Drawer_Double_Height.stl

Drawers_Minifinity_4x6.stl

Explore an intricately designed 3D model of a desk organizer at thangs.com under the category of devices. Crafted with great precision by the talented designer Henryshop3dforu, this 3D model represents a perfect balance between functionality and aesthetics. This model is an ideal inspiration for anyone interested in adding a touch of organization and style to their workspace. This desk organizer 3D model offers a user-friendly organized system to keep all your essentials like stationary, papers, and devices at arm's reach, reducing clutter, and aiding in productivity. The images provided give a comprehensive view of the Space-friendly, compact design, sophisticated look, and clean lines. This impressively detailed 3D model of a desk organizer is a testament to the limitless possibilities of 3D modeling. For a closer look at this desk organizer 3D model, visit our website thangs.com, and discover the limitless possibilities of 3D modeling today.

Desk organizer

Desk organizer A.stl

A 1x1 set of Gridfinity bins, sized so that they line up to form tiered rows when arrange by height.

Suggest standard printing profiles.

Gridfinity by Zack Freedman.

Gridfinity | Tiered Bins

Gridfinity_tiered_1x1_sm.stl

This is similar to other parametric models, but this is OpenSCAD based.

Turns out its hard to fit a grid of a different dimension inside another grid of a different dimension reliably without relative alignment. But it's been done, so here you go.

This is a gridfinity 1x2 with 2x3 tray routes for six total trays.

There is also a lid that can be printed should you want to keep your parts contained and separated.

~If I find a bigger use for this I will fix the code to be properly parametric.~ It has been done.

https://doslabelectronics.com/
https://ko-fi.com/mrcbax


Parametric Gridfinity Small Parts Containment Tray 

gridfinity_small_parts_containment.stl

**Check my Profile for more sizes!**
These USB Cable Storage Organizers are designed to print easily and store your USB cables securely in an optional magazine, or Gridfinity compatible magazine included. Deep plug area allows you to place your USB plug end in, wrap your cable and insert the end into the same area.




Big thanks to DC_Sublime for his work on scaling the Gridfinity, his models can be found here: https://thangs.com/designer/dc_sublime
Although designed 95% from scratch, this model was inspired/remixed from the TotallyRidiculous great Cable Keeper model found here: https://www.printables.com/model/520851-cable-keepers



USB Cable Storage Organizers (SMALL)

USB_Cable_Storage_75mm.stl

USBCableMagazine_Flat_v2.stl

Gridfinity_USBCableMagazine_1x5.stl

Gridfinity_USBCableMagazine_1x6.stl

A 2x2x1u Can holder for your Gridfinity setup.  Short and Tall versions available.

Suggest printing using standard profiles using no supports.

Gridfinity by Zack Freedman

Gridfinity | Can Holder

Gridfinity_Canholder_Tall.stl

A 1x3x3 Drawer in a looooong format, based upon the Gridfinity framework developed by Zack Freedman.

Suggest standard printing profiles for the chest, printed with body cavity facing upwards (tall and skinny-like), and printing the drawer piece with the body cavity facing upwards (trough-style) as well.

Gridfinity |  Long Drawer

Gridfinity_LongDrawer_2_Compartment_Drawer.stl

Gridfinity_LongDrawer_3_Compartment_Drawer.stl

Gridfinity_LongDrawer_Drawer.stl

Designed to interface with Zack Freedman's #Gridfinity system. Dedicated spots for bulk AA, bulk AAA, AAAA, 2032 (CMOS battery), A97/LR44/Other (Calipers, etc.), 18650 and 9-volt batteries. Prints well with 0.4 or 0.6 nozzle. 

Supports not necessary unless you're using the magnet holes in the bottom, in which case you'll want supports on "touching buildplate" mode. Tolerances are tight at ~0.5 mm due to the sizes of the batteries and needing to stick to 3-unit-wide model, but this should be achievable with pretty much any printer. For best printing, only adjust horizontal expansion if necessary to fit the batteries since the walls are all modeled to multiples of 0.4mm. Changing horizontal expansion will likely increase print time and reduce quality.

Gridfinity 3x5 Ultimate Battery Holder (AA, AAA, AAAA, 2032, LR44, A97, 18650, 9v)

This item is for use with the [#GridFinity system](https://www.youtube.com/watch?v=ra_9zU-mnl8) by Zach Freedman.

This is a 3x4 stepped paint shelf compatible with AK and Vallejo 24mm squeeze bottles.

UPDATE
Added requested sizes 1x4 and 3x5.

UPDATE

Added the source file and also a 3x3 version in STL. Increased the hole size slightly as it was a bit tight.

UP-UPDATE
One file was broken, it's fixed now. Also added a 2x3 version.

#Gridfinity Paint Shelf

This item is for use with the [#GridFinity system](https://www.youtube.com/watch?v=ra_9zU-mnl8) by Zach Freedman.

This is a 3x4 stepped paint shelf compatible with AK and Vallejo 24mm squeeze bottles.

Paint Shelf 1x4.stl

Paint Shelf 2x3.stl

Paint Shelf 3x3 Fixed.stl

Paint Shelf 3x5.stl

A 3x3x32cm Paper Towel Roll holder for your  Gridfinity arrangement.

Suggest standard profiles with 25%-50% infill. There is a thicc area at the bottom of the dowel for increased strength.

Gridfinity concept by Zack Freedman

Gridfinity | Paper Towel Roll

Need a desk organizer and a best friend? Look no further! Desk buddy will always be there for you when you need a pencil or to help you through that existential crisis!

**Print Settings**
I printed my Desk Buddy at .2mm layer height with 15% infill. I needed to use supports on the arms.

Happy Printing!

Desk Buddy

Desk Buddy.STEP

Based on my original small Rugged Desktop Organizer, now biggie sized and GRIDFINITY COMPATIBLE 2x3!

**Includes Bambu Studio single and 2 color .3mf files.**

Rugged Organizer LARGE Gridfinity 2x3

Rugged_Organizer_LG_Gridfinity2x3.stl

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](https://www.youtube.com/watch?v=ra_9zU-mnl8)

**UPDATE**
_Hole sizes increased by 0.2mm to allow better tolerance._

 A 1 wide by 2 deep by 2 unit high Standard Sharpie holder MAXIMIZED to hold an outstanding 14 Sharpies or other 12mm cylindrical items. The wells are 65mm deep. Also available in a pathetic 1x1 version holding a meager 5 items.

Contrary to Zach's instructions, I've been printing all my modules with a 0.8 nozzle, which seems to work just fine. This was printed with black eSun PLA at 75mm speed on an ender 3 pro with 0.8 nozzle and 0.32 layer height without support. 

#Gridfinity Sharpie Holders

1x2x2 Sharpie.stl

This is a from-the-ground-up reimplementation of Zack Freedman's divided Gridfinity boxes using CadQuery instead of Fusion 360. See this video for further information about the project:

https://www.youtube.com/watch?v=ra_9zU-mnl8

This version is customizable in CadQuery so you can generate custom sized divided boxes, including ridiculously large ones like 10x10 boxes etc. I have included a random selection of grid sizes from 1x1x2-high up. These should be fully compatible with the official boxes/grids. You can also fully customize the X Y and Z unit sizes AND the number of dividers on X and Y separately!

I re-implemented this because it seems like a perfect fit for an open source CAD software like CadQuery. With that in mind I have also released the source code python script that was used to generate the STLs. I would love for others to help me create new organizer bins and/or re-implement organizer bins in open source CAD software like CadQuery or OpenSCAD.

I used CadQuery/CQ-Editor to design this with a recent version checked out from github on April 13th, 2022. Unfortunately CadHub.xyz does not have a recent enough version of CadQuery to render this properly (n.b. the issue is with lack of a combine argument in the older version of the eachpoint method).

CQ-Editor is available from here, but please check out a 0.30dev version or newer to be able to compile the included CadQuery source code:
https://github.com/CadQuery/CQ-editor

f you are interested also check out all of my gridfinity models for baseplates and boxes here:
https://www.printables.com/social/107343-jdegs/collections/154274

And my related model for undivided gridfinity boxes here:
https://www.printables.com/model/174715-basic-undivided-gridfinity-boxes-cadquery-customiz

Source Code is available here since Thangs doesn't allow CadQuery python files:
https://www.printables.com/model/179040-divided-gridfinity-boxes-cadquery-customizable

REVISION HISTORY:

220427: Revision #1
- Fixed issue where the bottom thickness of the box was only 1.0mm above the top of the magnet/bolt holes, but was intended to be 2.0mm. Re-rendered all models and released revised python source code.

Divided Gridfinity Boxes (CadQuery Customizable)

divided box 1x4x3-hi and 1x3-divs.stl

A 3x3x1u Gridfinity Swing-Out Drawer.

Suggest printing with the drawer with body cavity facing upwards, and no supports.  Suggest printing body vertically, with the angled bridge pieces near the bottom, and no supports.

Gridfinity concept by Zack Freedman.

Gridfinity | Swinging Drawer

Gridfinity_Swinging_Drawer_Drawer.stl

I just bought my first printer, and as I was sitting here thinking about where to stuff all of the bits and bobs that came with it, and realized the printer had a built in drawer, it hit me, I could just make an organizer for it!

This is that organizer.

Ender 3 S1 Plus Drawer Organizer.stl

Based on the “sturdy and stylish” small and scalable Rugged Desktop Organizer is now **GRIDFINITY COMPATIBLE**  to offer more storage locations for more of your things.  New Single print to offer a nice finished look for your gridfinity storage.

Rugged Organizer Gridfinity 2x2

A 2x2x5.36cm Gridfinity container with a door that swings downward.

Suggest printing with standard profile, body piece with body cavity facing upward, and the door vertically with the fat, pegged part on the bottom, using generated supports, touching buildplate only at 1% support density.

organizer

Most Popular of All Time

Categories

Popular

Personalize

Trending