Cool Can Coozies (7 Designs)

scalesmini.stl

PCI low profile 4010 fan.3mf

I was looking for additional cooling for my slim case and liked don frechdachs' design (https://www.printables.com/model/363066-pci-fan-mount-for-40mm-fans) but it was for a normal height slot. So I created a new design for a low profile PCI slot.

Some differences in the design concept. I tried to keep it to a one piece design with no support but gave up. It is one piece but will need to add support and some filing to make it smooth enough to slide into the chassis at the tail end. 

40mm is slightly bigger than two PCI slot width so if the lower slot is occupied, do check if you have some clearance as the fan will encroach very slightly into the next slot.

If you want to do this, you'll probably know that a 12V fan is normally used for PC and can identify the 12V and ground on the fan header to tap to. I have plenty of spare 4010 fans from 3D printers so they are without PWM and of a different connector type (XH2.54).  

I have ordered some connectors (KF2510 3 pins) commonly used on motherboards and will do a interconnect to connect properly to the motherboard while preserving the original fan connector. 

You can also order a 40mm fan with 3 pins or 4 pins that will fit the motherboard fan header properly, or just go for Noctuas. 

Let me know in the comments if there is an interest in a normal height version and I will do it when I am able to.

*****

Want to buy me a coffee?
https://www.buymeacoffee.com/zer0s 

Clicking on my affiliate links below will give me a small kickback 
if you purchase something within 3 days. (at no extra cost to you)

AliExpress affiliate links:

KF2510 connector kits
https://s.click.aliexpress.com/e/_DmDtRxV
JST XH2.54 connector kits
https://s.click.aliexpress.com/e/_DFUeIRZ
40mm fans
https://s.click.aliexpress.com/e/_DC5YlPl

*****

Consolidated affiliate links of other 3D printing-related items:
https://wp.me/peMLu6-j

For Amazon affiliate links
https://wp.me/peMLu6-2C 

Universal High Airflow Aux Fan

AuxFan_Fan Shroud.stl

ARRMA Fireteam Dual 30mm Fan Mod.stl

Have an ARRMA Fireteam and the fan on the motor went out?  This print will replace the crappy 35mm 7.4v fan they used with two 5v 30mm fans.  Just need to wire up a buck converter and two 30mm fans.  This bolts into place and two bottom holes are available for zip ties to hold wires in place.

Buck Converter: https://amzn.to/42bAhYk
Fans I used (although any 5v 30mm would work) https://amzn.to/3WGxvJB


Was this model helpful for you? Consider supporting my work in any of the following ways!  Even the free options help the channel!

Consider dropping a tip https://koji.to/k/8E9J or
consider supporting my ongoing work https://www.patreon.com/makersmashup
Purchase anything on amazon after visiting our store page https://amzn.to/429HusI  Just click this link first!

No cost option to support my work?

- Subscribe to the YT channel
- Follow me on Thangs.com
- Watch videos on the channel!
- Share any of the videos on social media!
- Share my models with friends and family!



HMG7.2 ADXL345 22.5mm Horizontal Mount.stl

This STL is a component of the Hero Me Gen7 Printhead assembly for 3D printers.

**Hero Me Gen7 is a modular printhead platform for 3D printers with excellent part cooling and the most compatibility across printers, hotends, extruders, ABLs, and other components.**


 The Hero Me Gen7 is all about choice and personal preference. If you have been upgrading your 3D printer, you've made choices about what is important to you, Your choices are likely going to be different from everyone else. When choosing a hotend, extruder, and ABL combo (not to mention fans and accelerometers), where are you going to find a printhead platform that will accommodate all your selected components (which could be a rare combo), for your specific 3D printer AND provides part cooling that gives you great print results. **This is what the Hero Me Gen7 is all about!**


Think of the Hero Me platform as lego blocks for printheads, there are mounting parts for each component (hotend, extruder, fans, ABLs, etc.) that stack and mount to a core Base. Component specific mounting parts can be interchanged for another of the same type. So, should you change your component selection(s) in the future, you do not have to start over, you simple replace the single STL mount that is matched to the new component. There is no need to yet again go looking for a new set of mounting hardware that was not likely to have been designed to work with each other in the first place.


So to give you choice and fulfill your personal preferences in 3D printing, the Hero Me Gen7.3.2 now supports over 100 3D Printer models (plus clones), 46 Hotends, 34 Extruders (over 45 mount options), 17 ABL Sensors (34 mount options), 35 Part Cooling Duct options, 12 Cable Management options, 11 ADXL345 mounts, and 4 LED bar mounts (among many other options). Gen7.3.2 supports most of the popular 3D printers and components available. 


If you know your 3D printer model, hotend, fans, and optionally an extruder, ABL sensor, ADXL345 accelerometer (for Klipper), and any other options for your printhead assembly, you can scan through the Hero Me Gen7 Release 3.2 folder, or use the Thangs Advanced Search.  Be sure to set the creator filter to: ‘MediaMan3D’ then search for ‘HMG7’ which should bring up all the STLs. You can refine your search from there by component, brand, etc.


If you find that you have a 3D printer model or component that is not yet supported, send me information and preferably a STEP or STL (or link) if you know of one for the X carriage of that printer or the component and I will create a mount for it. Send to: MediaMan3D@gmail.com


If you want Hero Me documentation… The Hero Me Gen7.3.2 folder of STLs on Thangs is organized into sub-folders by component category, with sub—sub-folders for type and brand with well defined filenames to make it easy to find what you need. If you want documentation to help you select and assemble the Hero Me Gen7 for your specific 3D printer, you can get a membership plan here on Thangs.  You will get a detailed 56 page parts selection and illustrated assembly guide along with assembly videos, private Discord server access (with over 2,000 Hero Me users), technical support, and much more, You also get exclusive access to new STL releases 30 days before being posted to Thangs, and other STL libraries. Check out the membership plans here:  [https://thangs.com/designer/mediaman3d](https://thangs.com/designer/mediaman3d)

biqu b1 dual 5015 parts cooler with veiw port

This is a parts cooler for the Biqu b1 it holds 2 5015 fan blowers. It only uses 3 of the original 4 screws on each side. It also feature a nozzle vewport.

Cooling

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

View 78 new models

PCI low profile 4010 fan.3mf

Universal High Airflow Aux Fan

View 10 new models

View 510 new models

biqu b1 dual 5015 parts cooler with veiw port

Anycubic Mega Zero 2.0 5015 cooling fan duct

Steam Dock ( with cooling)

RBJ magnetic cooling system

Raspberry Pi & BigTreeTech Pico 40mm Fan Mount - Pi Zero 2W 3 4