Adapter for Sun filter sheet. Print two covers and locks. The cutting guide can be used to cut the sheet to size (round). The sheet should be handled with care.

Looking into the Sun is dangerous for the eyes. I used the Thousand Oaks 8" Sun filter which came with two sheets. Half of one is enough for the binoculars.

Celestron 80mm binoculars filter adapter

Celestron 80mm filter cover.stl

Wall mount for the newer version of Legrand power strips.

Video of me using the mount: [https://youtu.be/jN9Z--7o4N0?t=785](https://youtu.be/jN9Z--7o4N0?t=785)

Derived from https://www.printables.com/model/117247-support-multiprise-legrand

Legrand power strip mount

Wall mount for the newer version of Legrand power strips.

Derived from https://www.printables.com/model/117247-support-multiprise-legrand

For mounting heat guns on the wall. Fits the Einhell heat gun. Small radius 63mm, large radius 68mm. I printed mine in PETG and mounted it to the side of an Ikea cabinet.
Check out [the video](https://youtube.com/shorts/gfbUjfd7MeE?feature=share). 

Heat gun holder

For mounting heat guns on the wall. Small radius 63mm, large radius 68mm. I printed mine in PETG and mounted it to the side of an Ikea cabinet.
Check out [the video](https://youtube.com/shorts/gfbUjfd7MeE?feature=share). 

Relatively quick purge tuning for multi-color 3D printing. For Bambu Lab 3D printers or other single-nozzle multi-material solutions (MMU, ERCF, Palette).

Less accurate than [my Z-stacks](https://bit.ly/purge-zstacks), but does only one color change per color combination (vs 3.5 for the Z-stacks) and is faster to print. Usage is very similar to the Z-stacks model, using the same print settings.

I use this first to get a rough idea of which purge volumes need increasing. Then I print the Z-stacks model for further fine-tuning and better color checking.

**How to calibrate all colors**
- Calibration is needed every time filaments are changed, even when replacing a spool with another similar color.
- Pick the files for the specific number of colors to calibrate. The first digit in the file name represents the number of colors. Example: for 3 colors pick the files named 3-1, 3-2, and 3-3. Ignore files named "manual" unless you're testing specific transitions only (see next section). Only one tower can be printed at a time.
- Load the files in the slicer all at once (Bambu Studio or Prusa Slicer) Click YES to load them all as a single object with multiple parts (just like you would do for loading multi-part color models).
- Assign one color to each part. (In Bambu Studio, with the filament list loaded, look on the left side, under Process, and switch to Objects view. Then click the first part (eg 3-1) and press number 1. Click the next part (eg. 3-2) and press number 2 and so on). The model should show up colored.
- Make sure the material colors in the slicer resemble the actual filament colors somewhat and that they are synchronized with the printer.
- Prepare initial flushing volumes. One way to start is to use the Auto-Calc button on the Flushing Volumes window and reduce the multiplier to something like 0.5. Lower values will require more work, while higher values produce more waste.
- Print the model to check the transitions. See recommended print settings below.
- Carefully check all transitions on the printed tower. Each 4mm tall section should have a uniform color. If there is a color gradient, it means there's color bleeding. For all transitions showing color bleeding, increase the purge volumes. The 4mm sections use 400 mm³ of material, so a transition that uses half of the length would be 200 mm³. You'll have to eyeball it and it's sometimes difficult to tell whether or not the transitions are perfect. Use whichever side is easier to "read" for you. Note that Bambu Studio always rounds values up to at least 100mm³ when using a purge tower.
- To further tune and more accurate checks, continue printing the [Z-stacks model](https://bit.ly/purge-zstacks) which works in a similar way.
- Save as project to not lose the purge volumes. It's easy to have them reset. This way you can load the project with the values when using these specific filaments.

**How to calibrate selected color transitions** when only a few transitions require checking
- instead of loading the entire tower, decide how many color transitions you need to check, then load files called "manual". They include up to 22 transition pairs. You can load more than needed and remove the excess later.
- color each part with the colors needed for each transition you want to check.
- delete any pairs that are not needed.
- print the tower and adjust flushing volumes as explained in the previous section.

**Print settings**
Either use the settings below or import the [Bambu Studio print profiles](https://mihaidesigns.com/p/purge-optimization/bambu-studio-purge-test.zip).
- switch process to Global in Bambu Studio
- start with the standard print profile
- switch to advanced mode
- under Quality, use layer height 0.4mm
- first layer height 0.4mm
- all line widths: 0.55mm
- under Strength: 0 top shell layers
- 1% sparse infill density
- aligned rectilinear sparse infill pattern
- infill direction 90 (infill settings needed to support internal walls)
- under Speed: outer wall 25 mm/s
- inner wall 25 mm/s (needed to allow for enough layer cooldown and avoid speed changes between transition layers and single-color layers so they don't look different)
- under Others: set brim-object gap to 0
- disable prime tower (important!). Also, make sure all values in the Flushing volumes window are 100 or higher. I'll publish a printer profile that does this automatically, but it's not fully ready at this time.

Files for up to 8 colors included. For up to 16 colors check my [Patreon](https://www.patreon.com/mihaidesigns).


Purge calibration flat stacks for Bambu Lab and other single extruder multi-color 3D printers

sample.3mf

For use with Bambu Lab 3D printers or other single-nozzle multi-material solutions (MMU, ERCF, Palette).

This is the most accurate solution I found for tuning filament purge length, but also a bit annoying: it tells which purge lengths are too low, but doesn't say by how much the value is off. It takes a while as you have to run it multiple times. I also use a custom printer profile which I will publish once it's ready. This can still work without it.

There are 7 color changes for every two color combinations.

Thangs won't let me upload .zip files with a folder structure, so the files are all mixed up.

[Short video introduction](https://youtube.com/shorts/nNSx8B30cp0?feature=share).

**How to calibrate all colors**
- Calibration is needed every time filaments are changed, even when replacing a spool with another similar color.
- Pick the files for the specific number of colors to calibrate. The first digit in the file name represents the number of colors. Example: for 3 colors pick the files named 3-1, 3-2, and 3-3. Ignore files named "manual" unless you're testing specific transitions only (see next section). Only one tower can be printed at a time.
- Load the files in the slicer all at once (Bambu Studio or Prusa Slicer) Click YES to load them all as a single object with multiple parts (just like you would do for loading multi-part color models).
- Assign one color to each part. (In Bambu Studio, with the filament list loaded, look on the left side, under Process, and switch to Objects view. Then click the first part (eg 3-1) and press number 1. Click the next part (eg. 3-2) and press number 2 and so on). The model should show up colored.
- Make sure the material colors in the slicer resemble the actual filament colors somewhat and that they are synchronized with the printer.
- Prepare initial flushing volumes. One way to start is to use the Auto-Calc button on the Flushing Volumes window, and reduce the multiplier to something like 0.5. Lower values will require more work, while higher values produce more waste.
- Print the model to check the transitions. See recommended print settings below.
- Carefully check all transitions on the printed tower. For all transitions showing color bleeding, increase the purge volumes. I consider value 100 minimal, and Bambu Studio always rounds values up to 100mm3 when using a purge tower. By how much to increase the values is difficult to say. Perhaps add 20-30% if there's a bit of color bleed and 40-60% if there's a lot.
- Repeat printing the tower as needed, or only print specific color transitions (see instructions later using manual pairs).
- Save as project to not lose the purge volumes. It's easy to have them reset. This way you can load the project with the values when using these specific filaments.

**How to calibrate selected color transitions** when only a few transitions require checking
- instead of loading the entire tower, decide how many color transitions you need to check, then load files called "manual". They include up to 22 transition pairs. You can load more than needed and remove the excess later.
- color each part with the colors needed for each transition you want to check.
- delete any pairs that are not needed.
- print the tower and adjust flushing volumes as explained in the previous section.

**Print settings**
Either use the settings below or import the [Bambu Studio print profiles](https://mihaidesigns.com/p/purge-optimization/bambu-studio-purge-test.zip) and enable prime tower if you normally print with the default profile (width 35mm, volume 45mm3)
- switch process to Global in Bambu Studio
- start with the standard print profile
- switch to advanced mode
- under Quality, use layer height 0.4mm (to reduce the number of color changes)
- first layer height 0.4mm
- all line widths: 0.55mm
- under Strength: 0 top shell layers
- 1% sparse infill density
- aligned rectilinear sparse infill pattern
- infill direction 90 (infill settings needed to support internal walls)
- under Speed: outer wall 25 mm/s
- inner wall 25 mm/s (needed to allow for enough layer cooldown and avoid speed changes between transition layers and single-color layers so they don't look different)
- under Others: set brim-object gap to 0
- when it comes to prime tower, I disable it for this test because I normally print with a slim tower and custom printer profile. If disabling the prime tower, make sure all values in the Flushing volumes window are 100 or higher. I'll publish a printer profile that does this automatically, but it's not fully ready at this time.

Files for up to 8 colors included. For up to 16 colors check my [Patreon](https://www.patreon.com/mihaidesigns).

Purge Calibration Z-stacks for Bambu Lab and other single extruder multi-color 3D printers

3-2.stl

I designed this back in 2019 to split 2kg spools into 1kg spools.
Used to transfer filament between two spools:
- Spool ID down to 12mm
- Spool OD up to 300mm
- Maximum spool height/thickness depends on the inner diameter (at least 110mm for most spools)

👉 [YouTube Video](https://youtube.com/shorts/99-BicFGMBY?feature=share)

**Print** all parts once. They are pre-oriented with built-in supports. Outer brim can help for the standing parts. You can use 3 perimeters for the vertical columns, but 2 is probably enough. No other special settings. I printed in PETG.

**Sourced parts**
- M3x30mm screw (or longer)
- 4x 6001 bearings
- power drill
- piece of 4x2mm PTFE tube, 20-30cm long
- small pieces of filament for assembly (I use nylon filament, but PETG or TPU are also good options). PLA may work as well but is more brittle

No detailed assembly instructions. Just a few glimpses in the video above.

**Operation**
This device can be dangerous. Use it at your own risk.
**Do not use high speeds and avoid sudden stops!** The source spool has no braking system and will continue to unwind and can tangle the filament.
Do not touch the filament with an empty hand/skin while it's being transferred between spools (always use the PTFE tube). Do not try to stop a spool rotating at high speed with bare hands.

More projects at [mihaidesigns.com](https://mihaidesigns.com/)

Supportless, support free.

Tape Machine - filament rewind / respooling

assembly preview.obj

Designed for the 10 kg AzureFilm spool (230mm thick x 300mm diameter). No additional parts requred.

Video https://youtube.com/shorts/iIYbpCjPMmY?feature=share

**Printing**
Parts are pre-oriented and with supports included.
Choose the 230mm version (230mm thick spools) if you can print 246mm tall pieces, otherwise choose the 190mm version (prints 206mm tall)

Parts to print:
- 1 roller (230mm or 190mm)
- 2 connectors (same size as roller)
- 1 roller cap
- 2 sides

Recommended stronger than normal settings. Perhaps 3-4 perimeters/walls, at least 20% cubic or grid infill. The roller and cap are the most sensitive parts. I printed in Fiberlogy Vertigo PETG.
I print at the higher end of the recommended temperature range for better layer adhesion.
To avoid roller seam, I suggest printing the roller separately with random seam position.

**Assembly**
Requires no screws, but is a bit tricky to assemble and can use some help from a second person.
Screw in the connectors to one side without tightening.
Hold the second side at the other end of the connectors.
Unscrew the two connectors while continuing to hold the sides at the ends of the connectors.
Screw in the two connectors at the same time to both sides and gently tighten. Spool holder is now assembled.
Screw the roller cap into the roller.
Place the roller on top of the spool holder. it should rotate easily. Make sure it's centered. For heavy spools, use a bit of grease at the contact points.

Handle with care and avoid shocks or dropping heavy spools on it. For direct-drive extruder use a reverse Bowden tube (PTFE) connected to the 3D printer frame to avoid jerk.

CAD files for further customization (different spool sizes) available for Patreons https://www.patreon.com/mihaidesigns.

10 kg Spool Holder

assembled view.stl

3D printed AMS stacking stand. Fits the Bambu Lab AMS (for P1P and X1 series 3D printers)

> [Quick presentation video](https://www.youtube.com/shorts/__9SEiFJhKI)

**Compatibility (updated)**
Fits the 3 different versions of the AMS units. However, the fit for the older version (3 large gaps on the sides instead of 4) is slightly offset and the bottom box will protrude out a bit.

**Materials**
- about 500g of filament
- optional 10x404mm metal rod/pipe (such as an aluminum pipe) cost me about $2 at the hardware store
- optional two M3 grub screws 6-12mm long and compatible Allen (hex) key (you can find them in sets on Amazon for $10-20), OR use long normal M3 screws, like M3x30 or M3x40 and only screw in a quarter of the length
- optional felt pads for the bottom AMS unit for easier sliding

**Printing**
There's an optional small test-fit part that can be printed first for checking potential fitting issues. Let me know so I can add more files with different clearances or different rod diameters.
Pick either the decorated version or the plain version. 2 files need to be printed and they are pre-oriented, no supports required.
I prefer PETG, 2 perimeters, 12% cubic infill, and a good amount of brim. Takes close to 15 hours to print with the Generic PETG profile.

**Assembly**
Cut the metal rod to 404mm long, then insert it in both printed parts.
Fit the AMS unit at the top.
Screw in the two grub screws at the back alongside the rod to lock it in place.

If you like CAD modeling, I posted a [90-minute video with the entire workflow for creating this model](https://youtu.be/lQgtJk67J3Q).

Licensed under [CC BY-NC-SA 4.0](https://creativecommons.org/licenses/by-nc-sa/4.0/) (in short: you may use, adapt, and share these files non-commercially with attribution and under this same license).

AMS stacking stand for Bambu Lab P1P and X1 #ThangsBambuContest

AMS Stand 10mm rod - decorated left.stl

A railway track for turning the [Love Bug](https://bit.ly/lovebug-thangs) into a train. Curves, branches, intersections, semaphores.

I enjoyed printing the [Love Bug Caterpillar](https://bit.ly/lovebug-thangs) by @ChaosCoreTech and turned it into a train on tracks 😄 I printed the Love Bugs in [coextrusion filament from 3DJake](https://www.3djake.de/3djake/magicpla).

If having issues with clearances, try printing the tracks 1-2% larger.

Check out my larger projects at [mihaidesigns.com](https://mihaidesigns.com/) and be awesome!

Love Bug Railway

curve.stl

Helper tool for 3D printer E-steps calibration.

Print either tool (larger one provides more accuracy) and use with [my calibration wizard](https://mihaidesigns.com/esteps/).

[Video on YouTube](https://www.youtube.com/watch?v=8RqS5cAt_GQ).

Tools feature filament marking points and a built in ruler for measuring the error. The larger tool includes adhesion supports that need to be removed before use.

Check my other projects at [mihaidesigns.com](https://mihaidesigns.com/).

Extruder E-steps calibration tool

E-steps calibration tool 100mm.stl

Connector housings for the Mill Max 4-pin 4mm connectors. I used to run these for hotend wires in order to swap hotends on my PitStop 1 extruder.

**BOM** (for each connector)
- 2x 8x5 cylinder magnets
- 2x 10-12mm M3 screw (countersunk screws are safer)
- 2x slim zip ties
- 1 Mill Max pogo connector (mare or female as needed).
[More details on the connectors here.](https://mihaidesigns.com/pogo-connectors/)

My wiring order was: heater, thermistor, thermistor, heater.

Check my other projects at [mihaidesigns.com](https://mihaidesigns.com/).

Magnetic 4 Pin Pogo Connector

Male pogo connector

Makes hotend tubes 25mm to 55mm long.

Print with 0.4mm nozzle and typical settings.

[Step-by-step instructions](https://mihaidesigns.com/ptfe-tube-jig/).

**BOM:**
- 1 M3 square nut (thick or thin)
- 1 40mm M3 screw (socket head, fully threaded)
- Printed parts (typical printing settings)
- 4mm OD, 2mm or 1.9mm ID (Capricorn XS)

**Tools:**
- Cutter
- Power drill
- Small Philips (+) screw bit or screwdriver

Pre-supported, pre-oriented, built-in supports.

Check my other projects at [mihaidesigns.com](https://mihaidesigns.com/).

Universal PTFE Tube Jig

Length and widen

Fits ANY spool. Up to 1Kg as is (see photos), scale up for larger spools (see "Larger spools" section).

Can be printed on a Mini 3D printer. Prints in one piece, pre-oriented, zero assembly.

Option to pass the filament through a guiding hole.

**Print settings**
3-4 perimeters
20-30% infill
Material: PLA is more rigid with less friction, while PETG is less brittle.

**Larger spools**
Scale up depending on printer and spool size:
For 2-3Kg spools (up to 300mm diameter) scale up to 128%. If it won't fit your printer, try scaling it less on the Y axis (using non-uniform scaling). Scaling Y to 125% will fit an Ender3, while keeping X and Z scaled at 128%.

I prefer storing all filament in dry boxes, but this is my next best option.

No supports required. Support free. Supportless.

Check my other projects at [mihaidesigns.com](https://mihaidesigns.com/).

Universal Spool Holder, Fully 3D Printed

Fits ANY spool up to 1Kg.
Can be printed on a Mini 3D printer.
Option to pass the filament through a guiding hole.

I prefer storing all filament in dry boxes, but this is my next best option.

No supports required. Support free. Supportless.

Universal spool holder fully 3D printed in one piece

**3D printed containers for Brother TZe label tape storage**

- 3 different sizes, for housing 5, 10, or 12 TZe tapes.
- separate or shared compartments for housing extra thick tapes.
- lid with window option to quickly see the tape types inside.
- clip on lid that stays firm, yet is easy to take off.

[Check out the video!](https://www.youtube.com/watch?v=GUjdS9XwGNM)

**Printing**
- choose one size (5, 10, or 12) and print one of the lids and one of the bases.
- print with 0.4mm or 0.6mm nozzle at layer heights up to 0.3mm and 0.4mm respectively for fast printing
- enable "detect thin walls" if using 0.6mm nozzle
- to save material, you can use 10% rectilinear infill with 0 degree fill angle. With a 0.6mm nozzle you can print only 1 perimeter

**Where to get the labels?** (affiliate links)

**Brother P-Touch Cube label maker**: [US](https://amzn.to/3b1zNfo), [EU/DE](https://amzn.to/3E6XaRh), [UK](https://amzn.to/3E6gKNu), [Canada](https://amzn.to/3juDHlK). Often on sale! Requires batteries or charger. Prints on up to 12mm or 1/2" wide tape. Get the **Plus** version to print wider labels.

**TZe labels**: [US](https://amzn.to/3G88gXY), [EU/DE](https://amzn.to/3C8sChz), [UK](https://amzn.to/3vAnfoQ), [Canada](https://amzn.to/3b91XoE).

**More US labels**: [color labels](https://amzn.to/3dTINEM), [more colors](https://amzn.to/3oY1FsN), [iron-on fabric labels](https://amzn.to/3EZwdj8), [ribbon fabric labels](https://amzn.to/322G1ur).

**More EU labels**: [color labels](https://amzn.to/3oW1P3D), [pastel and glitter](https://amzn.to/325EkfK), [iron-on fabric labels](https://amzn.to/31YyGMG), [ribbon fabric labels](https://amzn.to/30qhD5g).

**Asia labels** (worldwide shipping): [label packs](https://s.click.aliexpress.com/e/_ATgSwe), [FX labels](https://s.click.aliexpress.com/e/_9zlelc), [various size labels](https://s.click.aliexpress.com/e/_9gvBAi) (up to 12mm wide work on both label makers), [iron-on fabric labels](https://s.click.aliexpress.com/e/_9A7cxY), [ribbon fabric labels](https://s.click.aliexpress.com/e/_ABlJMO).

**Troubleshooting**
For the lid clip to work, printer needs to be well calibrated, with a flat and leveled build plate and extrusion calibration. If the lid is still difficult to take off, try filing the lid clips. If the lid releases by itself, try increasing XY Size Compensation.
For safety precautions, I don't recommend holding the full box by the lid.

Check my other projects at [mihaidesigns.com](https://mihaidesigns.com/).

TZe Label Tape Canister

10 base.stl

3D printed caster wheel adapter for Ikea Adils table legs.

[See it in action (video)](https://youtu.be/5-J3KBxTkZ0)

Recommended print settings: 4+ perimeters, 30%+ infill. No supports needed.

Requires caster wheels and screws. I recommend heavy duty caster wheels with a locking mechanism that prevents swivel.

Distance between screws measured diagonally: 51mm. Let me know if you need a different size.

If you want to pick up the table, add a bit of double sided tape to prevent the wheels from falling off.

Warning: risk of injury. Do not use with heavy load.

Check my other projects at [mihaidesigns.com](https://mihaidesigns.com/).

Supportless, FDM.

Ikea table caster wheel adapter

3D printed caster wheel adapter for Ikea Adils table legs.

Recommended print settings: 4+ perimeters, 30%+ infill. No supports needed.

Check my other projects https://mihaidesigns.com/

Supportless, FDM.

Ikea table caster wheel adapter.stl

3D printed stand for the Yamaha GL1 Guitalele.

Watch the video https://youtu.be/B4aPmMSBe0Y

Printed on MK3S in Galaxy Black. Fits Ender 3 if positioned diagonally. No supports needed.

Designed for 70mm thick instrument. Scale up/down for other guitar or ukulele (as long as you can fit it on the build plate).

Guitalele GL1 (affiliate links): [Amazon US](https://amzn.to/3ib6LOr), [EU](https://amzn.to/3idf2BA), [CA](https://amzn.to/2ZA8Ywt), [UK](https://amzn.to/3m2G9Aj).

Check my other projects at [mihaidesigns.com](https://mihaidesigns.com/).

Supportless, FMD, musical instrument.

Guitalele Stand

3D printed stand for the Yamaha GL1 Guitalele.

Printed on MK3S in Galaxy Black. Fits Ender 3 if positioned diagonally.

Guitalele Stand.stl

__3D printed filament dry box__


An enclosure for one spool of filament featuring desiccant cages and hygrometer for reducing and monitoring moisture on hygroscopic filament. Rewind system with locking mechanism for when the spool is not in use. Check out [the videos](https://www.youtube.com/watch?v=rsfHs_I52mk&list=LLMvNnP9oAQl5IApL8XBQIkQ)!

Make sure to check the advantages and disadvantages first, and follow instructions on [the project page](https://mihaidesigns.com/drybox/).

__Printing:__
>* Print one base (filename starting with "print one base.")
>* Print one lid (filename starting with "print one lid.")
>* Print all 40 shared files (some are identical)


DXF files included for laser cutting windows.


See the [BOM list](https://docs.google.com/spreadsheets/d/1ia3ImaCrxpdLvES7OI8j2lGvnmtfEvpncn1Ds7_c1f0/edit#gid=0) for required parts.

Licensed under CC https://creativecommons.org/licenses/by-nc-sa/4.0/


If you like my projects, you can support my work on [Patreon](https://www.patreon.com/mihaidesigns)! 😎

No supports needed, supportless, FDM.

Mihai's DryBox

pick one base. front and side angled windows (default).stl

front_panel.dxf

side_panel.dxf

Learn and develop your design and 3D printing skills
- Download up to 10 paid models per month
- Private Discord access to Superfan Group
- How to design (Live, Q&amp;As)
- Project polls
- All benefits in the previous tier

Superfan 😍

Instant access to everything
- Unlimited downloads
- Private Discord access to Superfan Group
- All benefits in the other tiers

To the Moon! 😎

Interact with an awesome group of 3D printing enthusiasts
- Download up to 4 paid models per month
- Private Discord access to Live Group
- Early access to beta STLs and some dev files
- Live Q&amp;As
- Exclusive project updates
- Early access to most long-form YouTube videos
- My everlasting gratitude 🧡

Live 😃

AMS Stand 10mm rod - test fit part.stl

AMS Stand 10mm rod - decorated right.stl

AMS Stand 10mm rod - plain left.stl

AMS Stand 10mm rod - plain right.stl

For a 62mm round cutout in an 18mm thick horizontal or vertical surface. Also [available for 60mm cutout](https://thangs.com/designer/MihaiDesigns/3d-model/Cable%20desk%20grommet%2060mm-919354?manualModelView=true&source=All+Files).
Multiple assembly combinations possible: flat, turret, mushroom.

Message me on Discord for other sizes or improvement ideas.

Cable desk grommet 62mm

Desk grommet 62mm assembly preview.stl

Desk grommet 62mm front.stl

Desk grommet 62mm back.stl

Desk grommet 62mm cover.stl

Desk grommet 62mm turret.stl

Desk grommet 62mm mushroom.stl

Updated transition model for my extruder test to detect a range of issues in a single print (the preview above is broken). For details see my [inconsistent extrusion articles](https://mihaidesigns.com/inconsistent-extrusion/).

PrusaSlicer and Bambu Studio files with all custom settings provided for easier printing. Do keep all settings when switching to another printer profile.

Further discussions on Discord.

Extruder test transition

Extruder test transition PrusaSlicer.3mf

Extruder test transition Bambu Studio.3mf

Join my awesome group and let me help you enhance your 3D printing skills!
Use code AWESOME for 50% off the first month!

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

MihaiDesigns

Achievements

Novice Maker

Sapling

Voyager

Fan Favorite

Pinned models

AMS stacking stand for Bambu Lab P1P and X1 #ThangsBambuContest

Cable desk grommet 62mm

Extruder test transition

Celestron 80mm binoculars filter adapter

Legrand power strip mount

Heat gun holder

Purge calibration flat stacks for Bambu Lab and other single extruder multi-color 3D printers

Purge Calibration Z-stacks for Bambu Lab and other single extruder multi-color 3D printers

Tape Machine - filament rewind / respooling

10 kg Spool Holder

AMS stacking stand for Bambu Lab P1P and X1 #ThangsBambuContest

Love Bug Railway

Extruder E-steps calibration tool

Magnetic 4 Pin Pogo Connector

Universal PTFE Tube Jig

Universal Spool Holder, Fully 3D Printed

TZe Label Tape Canister

Ikea table caster wheel adapter

Guitalele Stand

Mihai's DryBox