The Fart Accordion Pha(r)t Edition

The bigger, longer and thicker version of [The Fart Accordion](https://than.gs/m/839352) for 57% more fun!

Depending on the size of your sausage shovels, this might be easier and sexier to play than the normal edition. Uses a bit more TPU of course (18,5g vs. 12g) but maybe it's worth it?

Check out the video of how it plays: https://youtu.be/JqhNWHeMRQU

The Fart Accordion

After years of intense R&D, I'm proud to present the perfect musical instrument: **The Fart Accordion**.

You need TPU to print this beautiful one piece musical instrument. Empirically tested to be a very good way to annoy your partner!

Check the video of how it plays: https://www.youtube.com/watch?v=vrLfxlpuedw

**How to print:**
Print the holey side on the print bed. I recommend printing it with 100% infill or enough top layers to get the finger side sturdy and airtight. Don't worry, it will still only take about 12g of TPU.

**How to play:**
Place the holey side on your palm so you get a nice seal. Wet the palm for extra juiciness. Then squeeze the instrument with your fingers. Alternate angles, rotation, position, speed, energy and sensuality to make it rain! The instrument and your fingers might need some loosening first before you start getting nice sounds. Keep practicing and try different palm positions! #sharethefart

UFO Abduction Illusion multi toy

UFO illusion assembled REF Only.stl

Lucky remix of Thor's Hammer Mk.II Keychain

shamrocks.stl

ZigZag Christmas Ornament

##Not to Be Sold
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

##About the Design
This is an elegant abstract sculpture masquerading as a Christmas ornament. It almost seems to change shape as you rotate it in different directions.

This ornament prints well with just a single perimeter. That makes it very light and lets the most light through is you use transparent/translucent filament. In fact, it positively glows. It also looks amazing printed with bichromatic or trichromatic filaments. 

The print shown in clear was printed with Matterhackers Transparent PLA. They were printed on an AnyCubic Mega S and sliced using Cura. I'll be adding pictures soon that show the ornament printed with Matterhackers Quantum Raspberry Gold and Translucent Blue printed on a Prusa MK3S+ sliced using PrusaSlicer.

##Resizing
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

##Print Time
About 5 hours

##Print Settings
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 mm.

*Infill*
Using PrusaSlicer, you won't need infill. Just set top and bottom to 1 layer and minimum shell thickness to 0.15 mm. That will keep the ornament light (about 13 grams) and will let the most light through if you use translucent/transparent PLA. 

If you use Cura, I would use support blockers set to 1-3 layers high to add infill just in those areas that are unsupported.

*Speed*
With PrusaSclier, I used the default speed settings for my printer and generic PLA. In cura, I used:
* Outer Wall: 35 mm/sec
* Inner Wall: 40 mm/sec
* Travel Speed: 60 mm/sec

*Build Plate Adhesion*
I used a brim. With the supports, you shouldn't need a raft.

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. If you get supports inside the ball, just add a support blocker.

* Support Structure: Normal
* Support Placement: Touching Buildplate
* Support Overhang Angle: 60 Degrees (Cura) and 67 (PrusaSlicer)

Arrow through the Heart

USB - Thumb Drive & SD Card Holder.stl

Created this because I found myself having way too many USB flash drives and needed them organized.

Fully Parametric Probe-Cable Wall Mounted Holder-Comb

cable_comb-12Teeth-6mmGap-30mmTeeth-2Holes.stl

Gridfinity 1x3 Universal Wrench Holder

Print two of these (one of them mirrored) and it should hold the majority of wrenches out there.  Fit two of mine easily.

FreeCAD model included.

Gridfinity 3x1 Universal Wrench Holder

PWM Servo HPS-0618SG

PWM Servo HPS-0618SG
*Full Assembly and Part file

Filacaster

Fused.stl

Mjølnir With Stand

Mjolnir1.STEP

Miku Hatsune - Vocaloid - 120 mm Fanart Model

Miku - Full AMENDED.stl

Contour Gauge

Contour Gauge Carrier and Nuts.stl

BIKE BMX .SLDPRT

QUADRO .SLDPRT

Guitar pick guitar keychain

Guitar pick guitar keychain. The name says it all xD. 
Check more projects on: https://www.youtube.com/channel/UCp3sDRwVkbm7b2M-2qwf5aQ/videos



musical instrument

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

The Fart Accordion Pha(r)t Edition

The Fart Accordion

View 31 new models

Lucky remix of Thor's Hammer Mk.II Keychain

ZigZag Christmas Ornament

View 22 new models

USB - Thumb Drive & SD Card Holder.stl

Fully Parametric Probe-Cable Wall Mounted Holder-Comb

Gridfinity 1x3 Universal Wrench Holder

PWM Servo HPS-0618SG

View 11 new models

Mjølnir With Stand

Miku Hatsune - Vocaloid - 120 mm Fanart Model

Contour Gauge

BIKE BMX .SLDPRT

Guitar pick guitar keychain

View 47 new models

Electric Guitar