Xbox Wifi Antenna Support

This print stabilizes the Xbox Wi-Fi Adapter antennas if the hinges are broken or you want to make sure the antenna is at a fixed 90 degree angle.

Ak47 Headphone Stand

AK-47.stl

Jarts Stylish headband/headphone mod

Stylish headband/headphone mod

Surface Wallmount

Wallmount.stl

gopro_9_v4.stl

dummy_gopro_body.stl

Degbit ‎EOS 100 bike light reflector lens

I lost the reflector from my bike light. The reflector keeps out water, and also ensures that the light points forward while also using the case as a heat-sink.

Printed with Prusa MK3S+

- Print with the bottom down, using base-plate supports only.
- Glue a piece of aluminium foil onto the slope as a reflective surface.
- Glue a piece of acrylic or other clear plastic to use as a lens cover. 
- Use thermal paste to connect the LED PCB to the casing
- I recommend gluing around the edge a little, to improve water-resistance



Headphone stand

I designed this Headphone stand up for some friends.  I printed  it in amazon basics PETG.  I have a .06 nozzle and printed at .02  I printed with supports touching the build plate only. 

Hedphone stand final_top v1.stl

Micro Camera Shelf

A small shelf for webcams that have a tripod screw thread. I use it to have my webcam stuck on the side of m enclosure for octolapses

Nintendo Switch Joystick (Aftermarket)

Sony TV remote holder for RMF-TX310U or similar

Holder for Sony TV remote.  Designed a holder for my Sony X900F TV remote. Works with other similar Sony TV remotes.

Sony TV remote holder

dji_mini_2 (1).stl

Speaker Ball Mount

I bought these speaker mounts, but the screw didn't fit my speakers so I created this so that I could use an M5 screw that did connect to my speakers.

Bill of Materials
	2x M5 35mm or longer
	4x M5 nuts
	Jumbl SINSB7B (or SINSB7W) ProGrip Ultra Stainless Steel Speaker Wall Mount Bracket - https://www.amazon.com/gp/product/B008J56UH0
	
Print Settings
Prints without supports if printed flat side down.

Cable guide

The hot end cables were dragging along the bed & pushing on the heated bed cables, causing the bed to move up and down during a print. (Ender 3 v2). 

So, I designed this little guide to hold the hot end cables up slightly so they don't interact with the bed. One side of the hook is chamfered so that the cables don't touch any sharp edges as they move. The guide slots into the frame of Ender/other 3d printers on the back left side. 

If you want to cable tie the cables into the guide, then just make sure it has enough slack for the hot end to reach the top right of the print area before tying it. 

It prints without supports, just make sure it's oriented with the long flat side down to the bed. Doesn't require supports.


Troy Lee Designs GoPro Chin mount

Simple chin mount for TLD Stage helmet. No Supports needed. Recommend using thin foam between mount and chin bar to prevent rubbing and vibrations.

troy lee designs GoPro Chin mount

Pi to Nikon Adapter

Raspberry Pi HQ Camera (C/CS Mount) to Nikon DX camera lens adapter.

Head phone Hanger v8.stl

camera mount vyper.stl

Mount for the Pi camera using the Pop apart lub tubes

wii controller Holder

Nintendo Labo VR Blaster Stand

This is an improved stand for the Nintendo Labo VR Blaster. I made this because the original stand for the blaster was quite small and weak and tended to fall over.

consumer electronics

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Xbox Wifi Antenna Support

Ak47 Headphone Stand

View 47 new models

Surface Wallmount

gopro_9_v4.stl

dummy_gopro_body.stl

Degbit ‎EOS 100 bike light reflector lens

Headphone stand

Micro Camera Shelf

Nintendo Switch Joystick (Aftermarket)

Sony TV remote holder for RMF-TX310U or similar

View 12 new models

View 38 new models

Cable guide

Troy Lee Designs GoPro Chin mount

Pi to Nikon Adapter

Head phone Hanger v8.stl

camera mount vyper.stl

wii controller Holder

Nintendo Labo VR Blaster Stand