I found that the headband of the stock Head(amame) headphones (https://shop.vectorfinesse.com) slid off fairly easily.  This modification uses M4 screws to lock the headband to the cones while allowing the cones to rotate from side to side.

This is a remix of a few components that were purchased from https://shop.vectorfinesse.com.  You will need to puchase the other 3D printed parts to build a pair of headphones.

Bill of Materials
2x M4 18mm - 20mm screws

Headphone Headband M4 Mount

Headband.stl

A 200% scale of the Brick Block Puzzle Box (https://www.prusaprinters.org/prints/81772-brick-block-puzzle-box) by 3D Printy.  I decreased the diameter of the screw holes because the screw holes were too big for the M6 screws.  For assembly detail go to: https://youtu.be/BTbMbkgMOT8

Bill of Material
- 3 M6 20mm screws
- 15 6mm x 6mm cylinder magnets
- Super glue

Brick Block Puzzle Box 200%

Level_1_200.stl

A shelf designed for the RepRack: Open Source Spool Holder And Storage System by Repkord (https://www.prusaprinters.org/prints/129024-reprack-system-by-repkord).  The shelf clicks on to the 1/2" electrical conduit.  If you print this without top or bottom layers you save a bunch of filament and you get a cool looking shelf.  I like the the look of the gyroid infill.

RepRack Shelf

A shelf designed for the RepRack: Open Source Spool Holder And Storage System by Repkord (https://www.prusaprinters.org/prints/129024-reprack-system-by-repkord).  If you print this without top or bottom layers you save a bunch of filament and you get a cool looking shelf.  I like the the look of the gyroid infill.

This is a remix of the M3 Wallet to integrate a Tile Pro.  This can be combined with Wallet M3 with Metal Money Clip (https://www.thingiverse.com/thing:4912312).
	
Description - Prusa
This is a remix of the M3 Wallet to integrate a Tile Pro.  This can be combined with Wallet M3 with Metal Money Clip (https://www.prusaprinters.org/prints/71823-wallet-m3-with-metal-money-clip).

Remixed From
https://www.prusaprinters.org/prints/66414-wallet-m3-my-daily-wallet

Wallet M3 with Tile Pro

wallet_m3_top.stl

This is the best 3D printable wallet I've found.  The only flaw is that there really isn't space for dollar bills.  The original design has a middle section for money but the pressure of the money interferes with the rotating lid.  Instead I put the slim Tile (https://www.thetileapp.com/en-us/store/tiles/slim) into the money section.
	
I created this remix to accept a thin metal money clip which is a lot stronger than trying to 3D print a clip to hold money.
	
There are two versions of this base:	wallet_m3_bottom_with_money_clip_slot_20mm 
2.47 by 0.79 inches (60mm x 20mm) Money clip		https://www.amazon.com/gp/product/B078YQMZXT
	wallet_m3_bottom_with_money_clip_slot_40mm
2.75" X 1.5 inches (71mm x 39mm) Money clip	https://www.amazon.com/Travelambo-Carbon-Pocket-Minimalist-Business/dp/B01N35XJXP

Remixed From
https://www.prusaprinters.org/prints/66414-wallet-m3-my-daily-wallet

Wallet M3 with Metal Money Clip

wallet_m3_bottom_with_money_clip_slot_20mm.stl

I used the Cap Generator by Ziv Botzer to create two 24mm and one 30mm sink faucet plugs for the Mustee 23-in x 23.5-in 1-Basin White Freestanding Laundry Sink with Drain (https://www.lowes.com/pd/Mustee-23-in-x-23-5-in-1-Basin-White-Freestanding-Polypropylene-Laundry-Sink-Drain-Included/50111058).  I've used these plugs for several years and they've held up well.

Utility Sink Faucet Plugs

30mm Sink Plug.stl

A model of the Tile Pro (https://www.thetileapp.com/en-us/store/tiles/pro).

Tile Pro Model

This is a model of the Tile Mate (https://www.thetileapp.com/en-us/store/tiles/mate).

Tile Mate Model

This is a thin plate that you glue to the wall to indicate that a telephone wire is behind the plate.  I'm renovating my basement and covering over the ugly telephone jacks (because who uses wired phones any more) but I wanted to make the wires findable for me or future owners so I created this indicator plate.  The plate is only 1mm thick and is designed to be painted over so that it's visible but doesn't stand out.  To glue it to the wall I used construction adhesive but most any glue should work.  The plate also covers up the hole in the wall so you don't need to patch it.

Telephone Wire Indicator

I remixed this puppy for the board game Stuffed Fables. I printed the large version because my daughter really wanted it. The card for Stuffed Fables that goes with this miniature can be found at: https://www.boardgamegeek.com/image/4012892/pdclose

Stuffed Fables Boardgame - Niko Puppy Piece

I remixed this with a 22 mm base to go with the board game Stuffed Fables. The card that goes with this miniature can be found at: https://www.boardgamegeek.com/image/4012888/pdclose

Stuffed Fables Boardgame - Giraffe Piece

Stackable puzzle trays for when you don't have enough space.

Stackable Puzzle Tray

Stackable Puzzle Tray.stl

I bought these speaker mounts, but the screw didn't fit my speakers so I created this so that I could use an M5 screw that did connect to my speakers.

Bill of Materials
	2x M5 35mm or longer
	4x M5 nuts
	Jumbl SINSB7B (or SINSB7W) ProGrip Ultra Stainless Steel Speaker Wall Mount Bracket - https://www.amazon.com/gp/product/B008J56UH0
	
Print Settings
Prints without supports if printed flat side down.

Speaker Ball Mount

I designed this tag to fit on the edge of the SimpleHouseware 6 Tier Wall Mount Document Letter Tray Organizer (https://www.amazon.com/gp/product/B06ZZD2DRQ) to indicate what should go in that slot.  I used a label maker is put the words on.

Printed without supports.

Shelf Tag

A simple name plate I created for my printer enclosure.

Replicator 2000 Name Plate

Body1.stl

I created this mounting bracket and remixed the case so that I could easily remove my Raspberry Pi 3b+ from my 3D printer.
	
Remixed From
https://www.thingiverse.com/thing:3892091

Raspberry Pi 3b+ Slide Mount Case

RPI_3B_Bottom_WithSupportEnforcers.3mf

A model of the Spark Fun's Qwiic pHat Extension device (https://www.sparkfun.com/products/17512)

I used these models to create it:
- https://grabcad.com/library/female-pin-headers-right-angle-1-40pos-1-2-rows-1/details?folder_id=7384766
- https://grabcad.com/library/pld-connectors-1/details?folder_id=8356202
- https://grabcad.com/library/headers-male-2-54mm-smd-dual-row-1	

Qwiic pHat Extension Model

Qwiic pHAT Extension.3mf

I merged the Base Support and the Assembly Tool into a base that has the assembly tool underneath.
	
Remixed
https://www.thingiverse.com/thing:2890931
https://www.thingiverse.com/thing:2825646

Puzzle egg base with assembly tool

A series of heart shaped cookie cutters that can be used to make a stacked Valentines cookie cake.

Progressive Heart Cookie Cutters

Hearts.3mf

I built this model of the Pi Supply Switch v1.1 (https://uk.pi-supply.com/products/pi-supply-raspberry-pi-power-switch?variant=1560088805396) so that I could build a case for it (https://www.prusaprinters.org/prints/58454-pi-supply-switch-case).

Pi Supply Switch Model

Pi Supply Switch.3mf

This is designed for v1.1 of the Pi Supply Switch (https://uk.pi-supply.com/products/pi-supply-raspberry-pi-power-switch?variant=1560088805396). The model I built to create this case can be found at https://www.prusaprinters.org/prints/58452-pi-supply-switch-v11  
-  Use 3 x M3 8mm screws to attach the board to the base.
-  Can also substitute longer M3 screws but the screws may stick out the back)  
-  Print the button model 3 times.

Bill of Materials
3 x M3 8mm screws (can also substitute M3 6mm screws)

Pi Supply Switch Case

Pi Switch Case Top.stl

This connects a HERCULES 3 Amp Corded 5 In. Variable Speed Random Orbital Sander (https://www.harborfreight.com/3-amp-corded-5-in-variable-speed-random-orbital-sander-56458.html) to a 1 7/8" (48mm) hose.  The specific vacuum I use is the Rigid 5 Gal. 5.0-Peak HP Portable Wall-Mountable Wet/Dry Shop Vacuum (https://www.ridgid.com/us/en/5-gal-stor-n-go-wet-dry-vac).  The sander end of this adapter has grooves which provide a locking connection to prevent separation.

Print Settings
Printed without supports with the small end down on the print bed.

Orbital Sander Adapter

Sander Adapter.3mf

A prototyping modular test bed for Arduino, Raspberry Pi, and a breadboard.  These panels are connected together with M3 10mm screws and M3 square nuts or a clip for being completely screw less.  I also made a modification to the Raspberry Pi panel to make changing the micro SD card easier.

Remixed From
https://www.thingiverse.com/thing:754078

Modular Test Bed - M3 or Screwless

Raspberry Pi - M2 Mounting Screws.stl

This print combines the Logitech K780 keyboard with a tablet to create a laptop computer by locking the keyboard and tablet together.  By locking them together you can use the tablet much more comfortably on your lap.  The back braces are set for the width of a Microsoft Surface tablet but the length of the braces can be easily modified for any tablet like an Ipad.

Assembly Instructions
- Print one copy of each model but print 2 copies of the Rear Brace [tablet] x2.stl and Connector x2.stl.
- Glue the one end of each Rear Brace [tablet] x2.stl to the Center Mount.stl.  
- Glue the other end of the brace into Top Mount.stl.  
- For glue I recommend using https://www.3dgloop.com/shop/pla-gloop.

Bill of Materials
	Logitech K780 Keyboard
	Tablet
	Bluetooth enabled mouse

Logitech K780 Laptop

Full Print.3mf

A webcam mount for the Logitech HD Webcam C270. This webcam mount has 3 parts; the base which is screwed down, the middle part slides on to the base, and the top part slots in and can rotate.

Remixed from https://www.thingiverse.com/thing:3272618

Logitech HD Webcam C270 Webcam Mount

Webcam Mount - All Parts.3mf

A mount for the Logitech Extreme 3D Pro Joystick (https://www.logitechg.com/en-us/products/space/extreme-3d-pro-joystick.963290-0403.html).

Remixed From
https://www.thingiverse.com/thing:4576519

Logitech Extreme 3D Pro Joystick Mount

Flight Stick Mount

- Made the slots for the square nuts a little bit smaller to prevent the nuts from spinning.
- Increased the size of the hole for the charging cable.

Remixed From
https://www.thingiverse.com/thing:3884431

Bill of Materials
	4x M3 6mm screws
	4x M3 square nut

iPad Mini Picture Frame Wall Mount

Back.stl

These devices mount glass to wood.  The grooves in the bottom allows glue to hold the mount to the wood better.  The holes allow nails or tacks to reinforce the bond.  I created this mount to attach a piece of fused glass to the bottom of a Crokinole board (as seen in the images).

These mounts are printed without supports and can be printed in 20 minutes.  These come in 4 sizes for 4 thicknesses of glass; 5mm, 6mm, 7mm, and 10mm glass.

Glass to Wood Mount

Glass Mount - 5mm.stl

I created this shelf to clip on to the $10 filament shelf (https://www.thingiverse.com/thing:465371) so that the filament shelf could hold more than filament. One of the cool ways to print this is without top and bottom layers (see image) and with 10% gyroid infill. Without these settings the shelf is a little bit flexible but still plenty strong and you save a lot of print time and filament. I've printed this in both PLA and PETG.

Filament Shelf - Shelf Attachment

Shelf for Filament Rack.stl

A magnetic latch designed to hold the door of an enclosure made with 2020 aluminum extrusion.  I've included the Fusion file so that you can modify the holes for the size of magnets you have.  The Enclosure Side Latch - Improved.stl provides better support for the door when shut.

Build of Materials
6x 8mm diameter by 3mm thick neodymium magnets 
Super glue to glue the magnets in
	
If attaching to 2020 extrusion:
4x M4 or M5 8mm screws
4x M4 or M5 T-nuts 

Enclosure Latch

Enclosure Side Latch - Improved.3mf

This is one of my first designs using Fusion 360. I wanted a hinge that was strong enough to hold a 54 cm door made up of 2020 aluminum extrusion and a Plexiglas pane. The hole for the 5 mm shaft is intentionally tight to prevent the door from sagging (you may need a hammer or mallet to insert the shaft). The hinge should be printed in PETG with 100% infill and "Support on Build Plate Only". With these settings the 54 cm long door only sags about 3 mm.

Build of Materials
2x 5 mm linear shaft 60 mm long (or you can get a longer one and cut it down to size) - https://www.aliexpress.com/item/5mm-linear-shaft-26mm-40mm-50mm-60mm-120mm-200mm-300mm-400mm-500mm-harden-linear-shaft-chrome/32884366852.html?spm=a2g0s.9042311.0.0.27424c4dw0PjDv

Enclosure - Hinge

A template to determine the location of the posts on a Crokinole board I'm building.

Crokinole Post Template

This case is designed for the DEWALT Countersink Drill Bit Set #6, #8, #10, 3-Piece (DW2535) (https://www.amazon.com/gp/product/B0000225OU/).  It also includes a slot for a standard countersink bit.
	
Remixed From
https://www.thingiverse.com/thing:3259395

Countersink Drill Bit Case

Top.stl

This leg for the Corsair P3 has a cutout for the power supply.

Remixed From
https://3dmakers.thermaltake.com/dwgallery.aspx?s=170

P3 Leg

For mounting the breakout box for my HTC Vive Pro inside of a Corsair P3 computer case.

Print Settings
No supports needed if printed with the front or back on the bed of the printer.

HTC Vive Breakout Box Mount

A vertically oriented dual 5.25 inch drive for the Corsair P3 computer case.
	
Print Settings
Print with the bottom side on the build plate (for orientation see P3 Dual Drive Bay.3mf).
Needs lots of supports

Corsair P3 5.25 Vertical Drive Bay

P3 Dual Drive Bay.3mf

This is a modified version of the Closetmaid Super Slider (https://www.amazon.com/ClosetMaid-5655-SuperSlide-Universal-Support/dp/B000KL4CGM) that I remixed to attach to 1 1/2 inch wire shelving.  See the original for instructions on how to install.
	
To be strong enough I printed in PETG with 10 perimeters.
		
Remixed From
https://www.prusaprinters.org/prints/47086-closetmaid-super-slider-for-generic-shelving

Closetmaid Super Slider for 1.5 Inch Generic Wire Shelving

Closet Maid Hook.3mf

An end cap for the Closetmaid rod (https://www.amazon.com/ClosetMaid-2051-SuperSlide-Adjustable-Hanging/dp/B00KZZ5JZQ).  This end cap is similar to the Closetmaid end cap (https://www.amazon.com/ClosetMaid-7563800-Hang-Endcap-Pack/dp/B000BQWUCE).

End Cap

I created this to defend my plants against the vicious new kitten we brought into our home named Loki. Loki enjoys stalking my helpless plants and devouring them before they've even had a chance to grow. I've included a photo of his trail of destruction. He might look cute but don't let his innocent looks fool you!

This model is printed in two parts and glued (crazy glue) together because it's too big for the printbed of my Prusa MK3s. I've included flanges to help in gluing the two halves together. Once your plants have matured you can flip the defender over and use it to raise up your Click and Grow device. The watering can in one of the pictures is this https://www.thingiverse.com/thing:871281 printed with Polyalchemy PLA Silver Elixir.

Plant Defender for Click & Grow

Plant Defender Part A.stl

Mounts the antenna for the ASUS TUF H370-PRO motherboard in the Corsair P3 computer case.

Remixed From:
https://www.thingiverse.com/thing:4216123

ASUS Antenna Mount

Another endcap for 2020 extruded aluminum

2020 End-cap

This case is designed to hold 4 standard sized nail punches.
	
Remixed From
https://www.thingiverse.com/thing:3259395

Nail Punch Case

Nail Punches Container.3mf

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

chking