Works with Sony remote RMF-TX500U or similar.

Sony TV remote holder for RMF_TX500U or similar

This headset hanger has a base that blends into the Dual Sense charging station. There is a hole in the the back to pass through the power cord to the charging station. 

Print the base as it sits. Print the hanger arm laying on its side. The two pieces should fit together without and adhesive, but printing results vary with printers.  I split this into pieces that would fit on my printer. If you need this split differently, please let me know.

Note: the image shows the PlayStation logo near the top of the hanger, but I moved it down to the middle in the uploaded model.

PS5 headphone hanger and base for Dual Sense charging station

Headphone stand v32.stl

Bathroom sink screen

This bracket goes into an empty 28mm hole where a 12v accessory outlet would be. 
Designed for the Kan Pas V39 ball compass. 
The offset version was created for my specific need to fit on my Honda CB500X.

Compass mount for  Kan Pas V39

CompBase.3mf

A simple holder for shower door frame to hang a squeegee. 

Shower squeegee / scraper hook

Hook for shower door frame to hang my shower squeegee. 

Squeegee hook.3mf

Put under kickstand for more surface area on softer ground. Printing is much less expensive than the bolt-on parts.  You can always print more if you lose it.

Motorcycle kickstand extender

Desk stand for Jabra Speak 410 or 510. Made this for home use of the conference speaker.

Jabra stand.3mf

Simple frame for motorcycle license plate. 

Fits Michigan and more. Check the guide below to see if compatible with your plate.  If you want something other than Honda logo, or a different size, please contact me. 

License plate size guide: https://www.webbikeworld.com/motorcycle

Motorcycle License Plate Frame

Holder for Sony TV remote.  Designed a holder for my Sony X900F TV remote. Works with other similar Sony TV remotes.

Sony TV remote holder for RMF-TX310U or similar

Sony TV remote holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5145285.

Radiator splash guard I designed for my 2021 Honda CB500X motorcycle. Should fit 2019-2021 models. 

The intent is to prevent water and debris coming off the front tire from hitting the radiator. 

I included the f3d file for those that want to remove the Honda powersports logo.

I printed with PLA+ and it is holding up fine.  That said, you may want to uses PETG or something better than PLA. This is somewhat close to the exhaust and will be subject to some heat in addition to rocks and such coming off the wheel. 

Honda CB500X Radiator splash guard

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5145993.

Mushroom stem for the Home Mini to make it look like a mushroom.

Two piece base and top that do not need supports to print. Print stem standing and top flat.  I did not need to glue mine together, but it depends on the accuracy of your printer. 

There is a one piece version if you prefer to print that way. 


At some future point, I may add a couple of smaller mushrooms to hide the cord.

Google Nest Mini mushroom stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4851260.

A stand put the Google Nest Mini in an upright position on a desk or shelf.  A small print, but fairly stable. The g2 has a notch to retain the cord.

I have printed this model standing without support, but you may wish to use support for the hook at the top that holds the mini in place. 

-------
Uploaded new 3mf files of revised versions. Revisions are only to some of the filleting and to the arc at the back of the g3 base.

Google Nest Mini stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4851242.

Created this to improve the sound coming out of my 55" Sony X900F television.  TV is wall mounted and speakers face down. This is a horn to redirect the sound forward. 

No science here, just something I whipped up in Fusion 360. 

The file is for one side; Left, if you are facing the TV. Mirror for the other side. Clips on to existing speaker grill. 

-----
Updated. Cleaned up the radiusing a bit. 

Sony XBR-55X900F speaker horn

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4860706.

A double remote holder from my single design.

Single remote: https://www.thingiverse.com/thing:4851387

Remote control holder - Double

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

johnco1126