Leap_Motion_20mm_Tube_Mount.STL

A mount for the Leap Motion Camera designed for attaching to tubular support structures with 20-21mm diameters. Attachment to the tubular support is done via standard hose clamps (ideally 8mm wide) running through the curved groove in the camera mount. Cutouts on either side allow the USB connector to be placed on either side of the mount, supporting both possible camera orientations.

Printed in PLA with the following settings (see also preview image):
20% triangular infill (not that important as infill is minimal)
0.2mm Layer height
6 solid top layers, 4 bottom layers
3 perimeters
with supports

Requires approx. 1.5h print time and 15.26g of material

BOSE Headset stand

bose head stand.STL

Mecanismo para pantalla de proyector

Pin.STL

Gridfinity 2x1 gopro 8 holder.STL

Gridfinity holder made for gopro hero 8. 
Uses a 2x1 base and is stackable. 
I printed it with base down, no support, otherwise close to default settings for pla. 

Gridfinity2x1 gopro holder.STL

Drone Brackets

it will fit most of the drones
You can see how i made it here https://youtu.be/SjO8qSh65Q8

Jak and Daxter - Scatter Gun

This is the Scatter Gun from Jak 2 and Jak 3. It's a WIP so it's not intended to be 3D Printed yet, but it's at a stage where I'm ok with folks having a play with and seeing if they can make it real.

Headphone Hook for Corsair x000D Series PC Case

one-piece-hook.stl

HEADSET STAND.STL

Blackmagic ATEM Mini Extreme mount bracket

This bracket is for mounting a Blackmagic ATEM Mini Extreme onto a Penn Elcom R1290/1U Sliding Rack Tray.  Use 10-24 bolts and square nuts.  (Washers also advised.)  The left bracket is provided - just mirror it in the slicer to get the right bracket.  It prints without supports on its outside face - you will need to rotate it in the slicer for print orientation.  This may work with other ATEM Mini models, but it was developed specifically for the ATEM Mini Extreme and hasn't been tested with any others.  The geometry of the mount points is simple enough that if you need to mount your ATEM Mini in a different way, it should be straightforward to edit the STL in modeling software.  I am also uploading the FreeCAD (version 0.20) model for any that would like to edit it in CAD.

Thank you to:
- Spudd1 [ATEM Mini & Mini Pro mounts](https://www.thingiverse.com/thing:4435878)
- richardhuss [https://www.thingiverse.com/thing:4803526](https://www.thingiverse.com/thing:4803526)
whose designs I referenced in creating this model.


Portable LCD Adapter

Long story short, I wanted a way to put my portable LCD in my backpack. I also wanted a way to set it up on my desk. 

I found an unused phone holder and used it. https://www.amazon.com/gp/product/B074PDJ6M8/ to hold my 15" screen: https://www.amazon.com/gp/product/B07TWGBG3P/

This mount allows you to use the VESA mount to connect it to the phone mount. Its likely you can use it with other things as well. Because it is so small of a mount I Can pack everything up in my backpack. A quick couple of turns and I'm good to go. 

Previously I used magents, but the screen was too heavy for it. The alternative are some mounts that must stay attached to the LCD which are not great for sticking in the backpack. 

Nintendo Joycon Keychain

Playstation Controller Keychain

Nintendo Switch joycon Guard

small guard to protect nintendo joycons while in a bag.

Switch joycon Guard

Finger Knob for Gopro Suction Cup.stl

This is a finger knob for an amazon brand suction cup attachment for a gopro 

iPad mini yoke mount C152_172, height adjustable

full design.stl

HexFire HexaCopter

HexFire_V1_-_Exploded_v1.stl

3D Printed Bluetooth Headphones

Headband - V5.1.stl

Phantom Drone Legs Extended

GoPro 130mm Straight Extension

I needed to mount my Akasa Action Sport Camera above and beyond my underseat bag so that the Power Bank battery could be placed in the rear pouch of the bag and a short USB cable could be run from the battery to the camera. So I designed this simple 130 mm extension that connects GestoPlastico's (https://www.thingiverse.com/thing:2598431) seat rail clamp to the camera mounting hardware. The extension rests on the bag for added support.

Gridfinity phone holder

Fits phones up to 15mm thicc

Templates: https://github.com/KptnAutismus/KptnAutismus

consumer electronics

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Leap_Motion_20mm_Tube_Mount.STL

BOSE Headset stand

Mecanismo para pantalla de proyector

Gridfinity 2x1 gopro 8 holder.STL

Drone Brackets

Jak and Daxter - Scatter Gun

Headphone Hook for Corsair x000D Series PC Case

View 11 new models

Blackmagic ATEM Mini Extreme mount bracket

Portable LCD Adapter

Nintendo Joycon Keychain

Playstation Controller Keychain

Nintendo Switch joycon Guard

Finger Knob for Gopro Suction Cup.stl

iPad mini yoke mount C152_172, height adjustable

View 10 new models

3D Printed Bluetooth Headphones

Phantom Drone Legs Extended

GoPro 130mm Straight Extension

Gridfinity phone holder