This bracket is for mounting a Blackmagic ATEM Mini Extreme onto a Penn Elcom R1290/1U Sliding Rack Tray.  Use 10-24 bolts and square nuts.  (Washers also advised.)  The left bracket is provided - just mirror it in the slicer to get the right bracket.  It prints without supports on its outside face - you will need to rotate it in the slicer for print orientation.  This may work with other ATEM Mini models, but it was developed specifically for the ATEM Mini Extreme and hasn't been tested with any others.  The geometry of the mount points is simple enough that if you need to mount your ATEM Mini in a different way, it should be straightforward to edit the STL in modeling software.  I am also uploading the FreeCAD (version 0.20) model for any that would like to edit it in CAD.

Thank you to:
- Spudd1 [ATEM Mini & Mini Pro mounts](https://www.thingiverse.com/thing:4435878)
- richardhuss [ATEM Mini Extreme mount](https://www.thingiverse.com/thing:4803526)
whose designs I referenced in creating this model.


Blackmagic ATEM Mini Extreme mount bracket

This bracket is for mounting a Blackmagic ATEM Mini Extreme onto a Penn Elcom R1290/1U Sliding Rack Tray.  Use 10-24 bolts and square nuts.  (Washers also advised.)  The left bracket is provided - just mirror it in the slicer to get the right bracket.  It prints without supports on its outside face - you will need to rotate it in the slicer for print orientation.  This may work with other ATEM Mini models, but it was developed specifically for the ATEM Mini Extreme and hasn't been tested with any others.  The geometry of the mount points is simple enough that if you need to mount your ATEM Mini in a different way, it should be straightforward to edit the STL in modeling software.  I am also uploading the FreeCAD (version 0.20) model for any that would like to edit it in CAD.

Thank you to:
- Spudd1 [ATEM Mini & Mini Pro mounts](https://www.thingiverse.com/thing:4435878)
- richardhuss [https://www.thingiverse.com/thing:4803526](https://www.thingiverse.com/thing:4803526)
whose designs I referenced in creating this model.


Continuing my series of dryerase supply holders for Gridfinity, this is a 1x1x6 Gridfinity block that packs in drops for 5 U Brands dryerase markers. These markers have an oval cross section, allowing us to just fit 5 drops into one Gridfinity square. As a nice bonus, if you get the 10 pack of markers, this allows you to fit the whole pack into just 2 gridfinity squares. The 4 outer drops are  19x15 mm ovals. The inner drop is a 19 mm diameter circle.

Gridfinity 1x1x6 ubrands dryerase markers holder.stl

Continuing my series of dryerase supply holders for Gridfinity, this is a 1x1x6 Gridfinity block that packs in drops for 5 U Brands dryerase markers. These markers have an oval cross section, allowing us to just fit 5 drops into one Gridfinity square. As a nice bonus, if you get the 10 pack of markers, this allows you to fit the whole pack into just 2 gridfinity squares.

This is a 2x1 Gridfinity block with drops sized to fit an Expo Dryerase Eraser and one marker.

Gridfinity 2x1 Dryerase Eraser and Marker Holder

This is a Gridfinity 1x1 block with drops for 4 markers. It was specifically made for the fat Expo dry erase markers, about 18.5mm diameter, but could be used for other markers of similar or slightly smaller size.

Gridfinity 1x1 4-marker holder

This is a Gridfinity 1x1 block with drops for 4 markers. It was specifically made for the fat Expo dry erase markers, about 18.5mm diameter.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

jjfoerch

Blackmagic ATEM Mini Extreme mount bracket

Gridfinity 1x1x6 ubrands dryerase markers holder.stl

Gridfinity 2x1 Dryerase Eraser and Marker Holder

Gridfinity 1x1 4-marker holder