Totodile - Pokemon - Fan Art

Eagle - Wall Decoration

EAgle.stl

6.25 Offset - Small Hole Center Marking Tool

6.25 Offset - Small Hole Center Marking Tool.stl

8x8 Legacy Tiles - 3x3 Board - Multi-Material Stack

8x8 Tiles - 3x3 Board - Multi-Material Stack.stl

6.25 mm - Quad Snaps (DS Part A) - Small Command Strip Mount

Quad Snaps (DS Part A) - Small Command Strip Mount.stl

Ocean Tadling

ocean_serpent_tadling.stl

Tail Keychains

CoralTail.stl

Baby Rose Dragon

Cinderwing3D Baby_Rose_Dragon.stl

Mini Print-in-Place Vise

**Print-in-Place Mini Vice**
This mini vise prints vertically as one piece using no supports. There are small pads on the moving jaws that reduce the clearance required in order to print it in place.  The risers under the vise allow the handwheel to be turned while sitting on a flat surface. The knob on the hand wheel should swivel as well.  The jaws are 64mm wide and  open to 80mm.  It has an overall printing height of 164mm.

**Print Instructions**
The moving jaws form on top of the serrations of the stationary jaw and as a result it’s important that you use a .4mm nozzle x .45mm line width, and .2mm layer heights if printing at 100%.  To free the jaws after printing I pried slightly with a screw driver on each side of the jaws before opening it with the screw.

The hardest thing about this print is probably the overhangs and bridging as a result of the weight saver holes.  If these hole are causing people issues I can make a version without them but I think most printers have adequate cooling to handle it. 

Printed on the [Muldex](https://github.com/3dprintingworld/MULDEX) rep-rap IDEX printer.

Printed with [3D Fuel Silver PLA]( https://www.3dfuel.com/collections/175ppla)


Print-in-Place Mini Vice

Small Swamp - With Free Dragon  - 5e DnD Inspired for RPG and Wargamers

Swamp 7x4 Small.stl

Cute Flexi Pets Pig (Keychain & Magnet)

Flexy pig_original.stl

Tray “waterdrop”

tray.stl

Eevee (Easy Print No Supports)

Eevee_STL.stl

Type 1, Big Thread Holes, 2x2 Inside Bracket

Type 1, Big Thread Holes, 2x2 Inside Bracket.stl

Printer Health Check - quick print torture test

This is a quick print printer health check.
It takes just over half an hour to print.
It has overhangs, holes, curved recesses, strings, posts, thin walls and surface details and part of the base is one layer thick so that you can check first layer quality.

Print at 0.3mm layer height with the 'print thin lines' box checked

|

Most Downloaded of All Time

Categories

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Totodile - Pokemon - Fan Art

Eagle - Wall Decoration

6.25 Offset - Small Hole Center Marking Tool

8x8 Legacy Tiles - 3x3 Board - Multi-Material Stack

6.25 mm - Quad Snaps (DS Part A) - Small Command Strip Mount

Ocean Tadling

Tail Keychains

Baby Rose Dragon

Mini Print-in-Place Vise

Small Swamp - With Free Dragon - 5e DnD Inspired for RPG and Wargamers

Cute Flexi Pets Pig (Keychain & Magnet)

Tray “waterdrop”

Eevee (Easy Print No Supports)

Type 1, Big Thread Holes, 2x2 Inside Bracket

Printer Health Check - quick print torture test

Screw-On Cleat

Tiny Egg Spider

Gemstone Tadling

8x8 MU - Simple Bolt-Locked Shelf

ATAT kit card 1 framed final.stl