Starburst Christmas Ornament

**ABOUT THE DESIGN**
This is a new variation on my Christmas Balls with Integrated Stems and diamond patterns.

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**RESIZING**
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

**PRINT TIME**
About 4.5 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height. I decreased the print temp from my usual 200 to 190 for this, decreased the flow from 115 to 105, and increased the outer wall speed from 20 to 30 mm/sec. That was enough to go from stem that was molten goo to one that printed perfectly.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 – 0.8 mm.

I had the best results using Cura setting the default width to 0.4 mm with an alternate extra wall. 

*Infill*
This does not need any infill. JUST DON'T DO IT.

*Speed*
* Outer Wall: 30 mm/sec
* Inner Wall: 30 mm/sec
* Top/Bottom Speed: 30 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I relied on the supports for build plate adhesion. 

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. 

* Support Structure: Normal
* Support Placement: Touching Buildplate
* Support Overhang Angle: 49 Degrees

I added a support blocker 75 mm x 75 mm x 110 mm set 15 mm above the build plate so that the supports would only be added to the bottom of the ornament.

Diamond Lattice Christmas Ball

Double Diamond Christmas Ball

###About the Design
This is a new variation on my Christmas Balls with Integrated Stems and diamond patterns.

###Not To Be Sold
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

###Resizing
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

###Print Time
About 4.5 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height. I decreased the print temp from my usual 200 to 190 for this, decreased the flow from 115 to 105, and increased the outer wall speed from 20 to 30 mm/sec. That was enough to go from stem that was molten goo to one that printed perfectly.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 – 0.8 mm.

I had the best results using Cura setting the default width to 0.4 mm with an alternate extra wall. 

*Infill*
This does not need any infill. JUST DON'T DO IT.

*Speed*
* Outer Wall: 30 mm/sec
* Inner Wall: 30 mm/sec
* Top/Bottom Speed: 30 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I relied on the supports for build plate adhesion. 

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. 

* Support Structure: Normal
* Support Placement: Touching Buildplate
* Support Overhang Angle: 49 Degrees

I added a support blocker 75 mm x 75 mm x 110 mm set 15 mm above the build plate so that the supports would only be added to the bottom of the ornament.

Diamond Christmas Ball Design 2

**ABOUT THE DESIGN**
This is a new variation on my Christmas Balls with Integrated Stems. It may be a little challenging to print. The key is to get the speed, temperature and flow right for your particular printer/filament combo so the stem prints cleanly at the narrowest point.

I printed this in Matterhackers Translucent Red. It's a nice balance between translucency and reflectivity. For an opaque filament, I'd use a multi-color PLA (like Matterhackers Quantum) or a medium toned silky PLA (gold, red, just use anything that's not really light or dark). Either type of filament would show off the facets nicely.

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**RESIZING**
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

**PRINT TIME**
About 4 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height. I decreased the print temp from my usual 200 to 190 for this, decreased the flow from 115 to 110, and increased the outer wall speed from 20 to 30 mm/sec. That was enough to go from stem that was molten goo to one that printed perfectly.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 – 0.8 mm.

I had the best results using Cura setting the default width to 0.4 mm and adding custom settings for the base of the ball that printed it 0.8 mm thick. You can do this by adding a support blocker to the bottom and giving it custom settings of 0.4 mm. Cura adds the two and prints the area within the blocker at 0.8 mm.

*Infill*
This does not need any infill. JUST DON'T DO IT.

*Speed*
* Outer Wall: 30 mm/sec
* Inner Wall: 30 mm/sec
* Top/Bottom Speed: 30 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I really relied on the supports for build plate adhesion. I used a brim, but I set it to 3.2 mm gap from the print so it would touch the supports but not the ornament.

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. 

* Support Structure: Normal
* Support Placement: Touching Buildplate
Support Overhang Angle: 45 Degrees

I added a support blocker 75 mm x 75 mm x 110 mm set 15 m above the build plate so that the supports would only be added to the bottom of the ornament.

Stocking Hook

Just a simple mantle hook for hanging stockings that I designed shortly before Christmas. Tested with up to 25lbs of weight. Easy print, no supports; I used PETG, 3 walls and 30% infill. Enjoy!

Fhw_ @Build_over_Bot edit (Blitzen) h left.stl

Hello Tribe,

Another of my eight tiny robot reindeer.

Cheers
Maker Millwright

Acorn - Screw It Yourself

exploded_view_DO_NOT_PRINT.stl

2023 glasses

Glasses to celebrate the new year, be the coolest of New Year's Eve. 

They are printed directly (they need support in the joint above the nose) and their assembly is very simple.

With a 1,75mm filament, you cut a piece and insert it between the sidepieces of the glasses and the support of the glasses and then you can use a spot heat or glue to fix it on the sides.

Santa Claus Sleigh Christmas Tree Decoration

This is a plain Christmas Tree Ball with the Santa Claus Sleigh silhuette and some different snowflakes designs.
It's designed to be printed in different colors to achieve the final result, if you want you can print it in one color and paint later.
This is the filament color change configuration if you print with 0.2mm layer using Cura "Pause at Height":
0 to layer 15 (0 to 3mm) = Red
16 to 19 (3.2 to 3.8mm) = White

ALL Frikarte3D designs are protected by the Copyright Law. By downloading, YOU HAVE NO RIGHT to sell any digital files or print models of my designs without my explicit written consent.

To sell them legally, message me so we can work out a deal.

Hope you like it! Any advice, or recommendation is welcome! Happy Printing!

I would be very grateful if you print it and put it on social networks to tag me at [@Frikarte3D](https://www.instagram.com/frikarte3d/)

Santa Claus Sleigh Christmas Tree Decoration 🎅🛷🎄

John McClane Christmas Tree Decoration

This is a John McClane (Bruce Willis) from Die Hard Christmas Tree Decoration. 
Die Hard is an action movie from the 90's and is considered as a Christmas Movie, then what's better to have that iconical character in your Christmas Tree?

It's designed to be printed in different color changes to achieve the final result, if you want you can print it in one color and paint later.
This is the filament color change configuration if you print with 0.2mm layer with Cura Slicer:
0 to layer 13 (0 to 2.6mm) = Light Skin
14 to 17 (2.8 to 3.4mm) = Black
18 to 21 (3.6 to 4.2mm) = White
22 to 25 (4.4 to 5mm) = Red

ALL Frikarte3D designs are protected by the Copyright Law. By downloading, YOU HAVE NO RIGHT to sell any digital files or print models of my designs without my explicit written consent.

To sell them legally, message me so we can work out a deal.

Hope you like it! Any advice, or recommendation is welcome! Happy Printing!

I would be very grateful if you print it and put it on social networks to tag me at [@Frikarte3D](https://www.instagram.com/frikarte3d/)

Hairify Remix of Frosty The Snowman

DISPLAY ONLY REMIXFROSTY.stl

Diamond Christmas Ball

After creating a bell with this pattern (see Diamond Christmas Bell, I wanted to see what it would look like as a ball. I loved it, so I had to share it with you. It printed easily for me with just a little support. It looks great with multi-color PLA, but it'll also look great in solid colored PLA (opaque or transparent).

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

***PRINT SETTINGS***
* Walls: 0.4 - 0.8 mm (I made the walls of the ball 2 lines thick and the walls of the stem 1 line thick).
* Layer Thickness: 0.15 mm recommended. Anything from 0.1 - 0.2 mm should look good.
* Infill: None. Seriously. It doesn't need it. It just adds weight and print time.
* Rafts/Brim: I didn't use either. 
* Supports: I added normal supports with an overhang angle of 56 degrees. It holds the ball to the printing plate and supports the extreme overhangs at the base without adding a lot of time to the print.

FHW: 2022 Modern Christmas Ornament ornament Ball 3

hello Tribe,
I think this is number 21 of this years ornaments.

Cheers
Maker Millwright

Snowman finger up

Remix of Estalactitas de hielo multi holder

Estalactitas de hielo decorativas.

Impresas sin relleno ni soportes.

Puedes añadirles luz led si lo deseas.

Estalactitas de hielo Decorativas

Steam Dock ( with cooling)

Cooling Dock - Complete.stl

Diamond Christmas Bell

This is the third in this year's Christmas bell series. It prints quickly ad easily. Use a nice medium toned silky, metallic or multicolored filament to show off the geometry - or use translucent filament to make it glow.

This is based on my closed lattice, spiral and open lattice bells. It's roughly the same size (slightly taller) with a new loop at the top and a new lattice pattern. 

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**PRINT SETTINGS**
* Walls: 0.4 - 0.8 mm (I used 0.4 mm for the clear bell and added an alternating extra line for the opaque bell)
* Layer Thickness: 0.15 mm recommended. Anything from 0.1 - 0.2 mm should look good.
* Infill: None. Seriously. It doesn't need it. It just adds weight and print time.
* Rafts/Brim: I didn't use either. However, the first layer is just a single width circle, so you may need to add a brim or raft.
* Supports: None. I designed this to print cleanly without them.

Elf (Little Big Head)

LBH-Elf.stl

Closed Lattice Christmas Bell

This is the third in this year's Christmas bell series. It prints quickly ad easily. Use a nice medium toned silky, metallic or multicolored filament to show off the geometry - or use translucent filament to make it glow.

This is based on my spiral and open lattice bells. It's roughly the same size (slightly taller) with a new loop at the top and a new lattice pattern. 

###Not to be Sold
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

*** PRINT SETTINGS***
* Walls: 0.4 - 0.8 mm (I used 0.4 mm for the clear bell and added an alternating extra line for the opaque bell)
* Layer Thickness: 0.15 mm recommended. Anything from 0.1 - 0.2 mm should look good.
* Infill: None. Seriously. It doesn't need it. It just adds weight and print time.
* Rafts/Brim: I didn't use either. However, the first layer is just a single width circle, so you may need to add a brim or raft.
* Supports: None. I designed this to print cleanly without them.

Candy Dispenser Planetary Snowman

Build your own Planetary Snowman

This Snowman has a planetary gear on the bottom so when you hold the center ball and spin the bottom ball his head rotates at 4 times the speed.  If you hold the center ball and spin the head, the bottom will rotate at 3 times slower. If you hold it by the head and spin the bottom or middle ball, it will spin freely, like a bearing. 

It is 133mm tall 100% and does not require supports. I used a .4mm nozzle at .2mm layer heights but a bigger nozzle or layers should work. If you scale it down it will make it more difficult to print but scaling it up will actually make it easier. I think it will scale up to at least 200% if not more without issue. 

Its hollow to save material, be sure not to add any details that extend to far into the inside as it could mess us the mechanics or create a part that should have supports. 


,christmas

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Starburst Christmas Ornament

Double Diamond Christmas Ball

Diamond Christmas Ball Design 2

Stocking Hook

View 13 new models

Acorn - Screw It Yourself

2023 glasses

Santa Claus Sleigh Christmas Tree Decoration

John McClane Christmas Tree Decoration

Hairify Remix of Frosty The Snowman

Diamond Christmas Ball

View 15 new models

Snowman finger up

Remix of Estalactitas de hielo multi holder

Steam Dock ( with cooling)

Diamond Christmas Bell

Elf (Little Big Head)

Closed Lattice Christmas Bell

Candy Dispenser Planetary Snowman

Hairify Santa Bust