#Gridfinity UPDATED 5/20/22! Hex Baskets

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](url)

 A 2 wide by 2 deep by 2 unit high basket with a hex mesh grid. I use this to store about 25 misc pens on a weighted base plate. 

Contrary to Zach's instructions, I've been printing all my modules with a 0.8 nozzle, which seems to work just fine. The basket was printed with silver PLA at 75mm speed on an ender 3 pro with 0.8 nozzle and 0.32 layer height without support. The basket is slightly spongy and flexible.

#Gridfinity 2x2x2 Hex Basket

Gridfinity IKEA ALEX Drawer Split 7x12 Frame for 220x220 Buildplates

Gridfinity_Alex_All.stl

Gridfinity 3x5 Ultimate Battery Holder (AA, AAA, AAAA, 2032, LR44, A97, 18650, 9v)

Designed to interface with Zack Freedman's #Gridfinity system. Dedicated spots for bulk AA, bulk AAA, AAAA, 2032 (CMOS battery), A97/LR44/Other (Calipers, etc.), 18650 and 9-volt batteries. Prints well with 0.4 or 0.6 nozzle. 

Supports not necessary unless you're using the magnet holes in the bottom, in which case you'll want supports on "touching buildplate" mode. Tolerances are tight at ~0.5 mm due to the sizes of the batteries and needing to stick to 3-unit-wide model, but this should be achievable with pretty much any printer. For best printing, only adjust horizontal expansion if necessary to fit the batteries since the walls are all modeled to multiples of 0.4mm. Changing horizontal expansion will likely increase print time and reduce quality.

#Gridfinity Wire Spool Holder

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](url)

This is a 4 unit wide by 1 unit deep by 1/4 unit high hook up wire spool holder. This is compatible with common wire hookup kits such as: [https://www.amazon.ca/CBAZYTM-Stranded-Gauge-Colors-Electrical/dp/B075M8DGYX/](url)

It will work with most common spool sizes, and uses a 6mm rod (as supplied with most kits). There are 6 threading holes at the front.

Contrary to Zach's instructions, I've been printing all my modules with a 0.8 nozzle, which seems to work just fine. The basket was printed with silver PLA at 75mm speed on an ender 3 pro with 0.8 nozzle and 0.32 layer height without support.

#Gridfinity Height Adaptive Spacers

2x2x025.stl

#Gridfinity Usb and SD Card Holder 

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](url)

 A 1 wide by 2 deep by 1/2 unit high USB thumb drive and SD card holder on a weighted base plate. 
 
Contrary to Zach's instructions, I've been printing all my modules with a 0.8 nozzle, which seems to work just fine. This item was printed with silver PLA at 75mm speed on an ender 3 pro with 0.8 nozzle and 0.32 layer height without support. The holder has slots for 4 USB Devices, 6 Standard SD cards and 6 Micro SD cards. The Standard slots are capable of holding 2 Memory Stick Duo's for all you PSP fans and even xD cards for you retro Fujifilm camera users. Tolerances are loose to allow the model to be printed easier on poorly configured printers that over extrude.

#Gridfinity Parametric Bit Holders

1x2 Bit Holder.stl

Gridfinity Baseplate Magnet Jig

#Gridfinity Parametric Lids

2x2.stl

Gridfinity File Holder.stl

#gridfinity small file holder is designed for keeping your small files or other small tools organised. Designed to fit into a common tool chest drawer.

#Gridfinity Paint Shelf

This item is for use with the [#GridFinity system](https://www.youtube.com/watch?v=ra_9zU-mnl8) by Zach Freedman.

This is a 3x4 stepped paint shelf compatible with AK and Vallejo 24mm squeeze bottles.

#Gridfinity Sharpie Holders

1x2x2 Sharpie.stl

#Gridfinity Raspberry Pi Case

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](url)

Say hello to the GFpi, a 2x2x3/4 Gridfinity module that holds a Raspberry Pi Model 4. Now your Gridfinity system can surf the world wide web! Front and side I/O slots give you access for all your cool peripherals and doo-dads. 

The Case is 3/4 of a unit high, enough to give space for 4 integrated standoffs and room for the height of the I/O. It is still stack-able should you desire it stay tuned for a series of stacking ring spacers for Gridfinity to let you convert odd size units to match up on heights!

Print with 0.4 nozzle as some walls are thin enough that larger sizes would not slice correctly. 

Gridfinity Chisel Holder.stl

#gridfinity chisel holders is make for a few different common shapes of wood working chisels.

Gridfinity model paint organiser

For all you model makers / painters out there I've designed a 3x3 #gridfinity organiser to keep your model paints and paint brushes tidy. There are 3 different size of paint brush holders. Enjoy!

#gridfinity

Trending this Week

Categories

Trending

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

#Gridfinity UPDATED 5/20/22! Hex Baskets

Gridfinity IKEA ALEX Drawer Split 7x12 Frame for 220x220 Buildplates

Gridfinity 3x5 Ultimate Battery Holder (AA, AAA, AAAA, 2032, LR44, A97, 18650, 9v)

#Gridfinity Wire Spool Holder

#Gridfinity Height Adaptive Spacers

#Gridfinity Usb and SD Card Holder

#Gridfinity Parametric Bit Holders

Gridfinity Baseplate Magnet Jig

#Gridfinity Parametric Lids

Gridfinity File Holder.stl

#Gridfinity Paint Shelf

#Gridfinity Sharpie Holders

#Gridfinity Raspberry Pi Case

Gridfinity Chisel Holder.stl

Gridfinity model paint organiser

Gridfinity Allen Key Holder

Gridfinity Bin Covers, Mid Plates, and Top Plates

Trading Card Organiser v2

Gridfinity Crimper holder.stl

Gridfinity Handheld Game Cartridge Holders