My asst Gridfinity Models, either other peoples that I Use, or ones I created

Gridfinity holder for the loctite super glue squeeze bottle. Zack's glue stick holder was too small by about a millimeter or two so I made this.

Gridfinity Super Glue Squeeze Bottle Holder

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](https://www.youtube.com/watch?v=ra_9zU-mnl8)

This is a 4 unit wide by 1 unit deep by 1/4 unit high hook up wire spool holder. This is compatible with common wire hookup kits such as: [https://www.amazon.ca/CBAZYTM-Stranded-Gauge-Colors-Electrical/dp/B075M8DGYX/](url)

It will work with most common spool sizes, and uses a 6mm rod (as supplied with most kits). There are 6 threading holes at the front.

**UPDATE**

I added the source file as per request, but it isn't parametric so heads up.

_I removed the raised front panel as it was pushing the spools back too far, the holes are in the gridfinity body now._

Contrary to Zach's instructions, I've been printing all my modules with a 0.8 nozzle, which seems to work just fine. This was printed with Black eSun PLA PLA at 75mm speed on an ender 3 pro with 0.8 nozzle and 0.32 layer height without support.

#Gridfinity Wire Spool Holder

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](url)

This is a 4 unit wide by 1 unit deep by 1/4 unit high hook up wire spool holder. This is compatible with common wire hookup kits such as: [https://www.amazon.ca/CBAZYTM-Stranded-Gauge-Colors-Electrical/dp/B075M8DGYX/](url)

It will work with most common spool sizes, and uses a 6mm rod (as supplied with most kits). There are 6 threading holes at the front.

Contrary to Zach's instructions, I've been printing all my modules with a 0.8 nozzle, which seems to work just fine. The basket was printed with silver PLA at 75mm speed on an ender 3 pro with 0.8 nozzle and 0.32 layer height without support.

"Time to tap out some holes!" you think. "I'll just grab my tap and... oh. It's not where I left it. I'll just tap the holes with the screw instead, that always works!"

------------------

Here's a 1x1 Gridfinity tap holder for this specific tap:
https://www.amazon.com/gp/product/B077HTXVR1

It may very well hold similar taps, but you'll have to try it for yourself!

#Gridfinity

Gridfinity 1x1 Thread Tap Holder

This Gridfinity compatible holder has four spaces in a 1x1 holder. The front two are 8 units high and the back two are 12 units high - perfect for a few pairs of tweezers and a feeler gauge - these tools are always right beside my printer, so I made my own storage just for them. 

Other makers have found these useful for assorted tools like cotton swabs (q-tips) and toothpicks as well! 

Gridfinity Dual-Height Tweezers & Feeler Gauge Holder

Don't want sawdust filling your open-top Gridfinity window bins?  Tired of screws and nuts spilling everywhere because you accidentally tipped over a bin?  Wouldn't it be great if the bins could have easily removable lids?

Here is my take on Zack Freedman's amazing Gridfinity window bins, 
https://thangs.com/designer/ZackFreedman/3d-model/Gridfinity%20Window%20Divider%20Bin-60754
but with lids!  

I started by remixing MaybeItsLesotho 's version 
https://thangs.com/designer/MaybeItsLesotho/3d-model/Gridfinity%20Window%20Divider%20Bin%20-%20no%20tape-229651
that has a slot for the mircroscope slide (no tape required!), then made a few custom modifications.

1. Created a lid for each size compartment.  Each lid has one or more magnets to hold it in place.
2. Added a slight overhang to the back of the bin to capture the lid.  Each id has a chamfer to slip under this overhang.
3. Added magnet pockets to the front plate that mate with the magnets in the lids.
4. Added small bumps to the back of the bin and the front plate, to help hold the lids in place side-to-side.

The design uses the same 6mm x 2mm magnets that are used to hold the bins in the grids.

Edit: By request, I've added the Fusion 360 files.  I didn't have access to the original Fusion 360 files, so I imported the STL, deleted some faces to clean them up, and then made my modifications.  They are not fancy parameterized files, so there is one file per model.  Maybe someday I'll rework them to combine with parameters.  In the meantime, I hope they are helpful!

Gridfinity Window Bin with Lid

Window Bin - 1 Compartment.stl

Window Bin - 3 Compartment.stl

Keep an eye on your VERY important notifications while topping up your battery! This phone charger fits the Gridfinity modular storage system, and is designed to hold [a particularly powerful Qi wireless charger](https://www.amazon.com/dp/B09HBFNQBR?psc=1&ref=ppx_yo2ov_dt_b_product_details). I designed it for my iPhone 14, but it should fit nearly any phone, even in an EXTRA THICC case.

To prevent damage, the adapter DOES NOT friction-fit. You will need a thin double-sided tape like carpet tape, or a removable adhesive like E6000.

Magnets or screws are VERY STRONGLY RECOMMENDED! Your phone wants to faceplant. It was born to die.

Fusion source: https://a360.co/3uoOinb

Gridfinity is the ultimate organizer for your whole workshop! Learn more at

Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Gridfinity Tips!

All storage blocks are compatible with all baseplates!
You can add [6x2mm magnets](https://amzn.to/3UuuJV9) to the corners!
You can also use [M3 screws](https://amzn.to/3VRrS9T) to secure the corners.

Gridfinity was inspired by Alexandre Chappel's ModuBOX system, which is found at https://www.alch.shop/shop/assortment

MagSafe Phone Dock.stl

Keep an eye on your VERY important notifications while topping up your battery! This phone charger fits the Gridfinity modular storage system, and is designed to hold [a particularly powerful Qi wireless charger](https://www.amazon.com/dp/B09HBFNQBR?psc=1&ref=ppx_yo2ov_dt_b_product_details). I designed it for my iPhone 14, but it should fit nearly any phone, even in an EXTRA THICC case.

To prevent damage, the adapter DOES NOT friction-fit. You will need a thin double-sided tape like carpet tape, or a removable adhesive like E6000.

Magnets or screws are VERY STRONGLY RECOMMENDED! Your phone wants to faceplant. It was born to die.

Fusion source: https://a360.co/3uoOinb

Gridfinity is the ultimate organizer for your whole workshop! Learn more at

Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Gridfinity Tips!

All storage blocks are compatible with all baseplates!
You can add [6x2mm magnets](https://amzn.to/3UuuJV9) to the corners!
You can also use [M3 screws](https://amzn.to/3VRrS9T) to secure the corners.

A 1x3x3 Drawer in a looooong format, based upon the Gridfinity framework developed by Zack Freedman.

Suggest standard printing profiles for the chest, printed with body cavity facing upwards (tall and skinny-like), and printing the drawer piece with the body cavity facing upwards (trough-style) as well.

Gridfinity |  Long Drawer

Gridfinity_LongDrawer_2_Compartment_Drawer.stl

Gridfinity_LongDrawer_3_Compartment_Drawer.stl

Gridfinity_LongDrawer_Drawer.stl

This is a remix of the Gridfinity Modular Drawer System that fits onto the Multibpard. I created a Peg with a slider on it and added slots to the back of the Gridfinity MDS so it can slide on and off the pegs easily. 

Gridfinity MDS Remix for Multiboard

Gridfinity-Modular-Case.3mf

A 1x1 unit that has 6 slots in it, 2.5 mm width, for holding rulers vertical in a drawer using the #gridfinity system. 

***Note**, This unit is can be stacked on top of other units, but can't be stacked on top of!

Gridfinity Ruler Holder

At the risk of having my nerd card revoked, I'll admit that I just don't need space for 6 nippers, strippers, and/or pliers. 

Rather than waste space with unused bays, I chopped Zack's original file down into this 2x2 Three-Bay Rack!

#Gridfinity

Gridfinity 2x2 Three-Bay Nipper, Stripper, Plier Rack

At the risk of having my nerd card revoked, I'll admit that I just don't need space for 6 nippers, strippers, and/or pliers. 

Rather than waste space with unused bins, I chopped Zack's original file down into this 2x2 Three-Bay Rack!

#Gridfinity

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5960760.

#Gridfinity RaspberryPi 4 Holder
Stores 3 x RaspbverryPi4 in a 2x2 grid

Fusion360
File included to mix sizes to your own requirements.

Other models
Check out my other models https://www.printables.com/@Micah_754861

Gridfinity - Raspberry Pi 4 (x3) holder + Fusion File

Straighten out your workshop with Gridfinity modular storage - deploy these plates anywhere you need some order!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Frame: https://a360.co/3ccHbsg
- Weighted Plate: https://a360.co/3uCJ2gR

The foundation of every Gridfinity setup is a baseplate, and these let you drop storage where you need it most.

**Frame**: The absolutely minimal no-frills baseplate. No room for screws or magnets, but saves filament and headroom. If your storage unit is on a steel surface, you can still put magnets in the storage blocks to keep them from sliding.

**Weighted**: Heavy, sturdy baseplate perfect for desktops, shelves, and other places where knocking stuff over is a big problem. 

Secure blocks permanently with [M3 screws,](https://amzn.to/37IaXTg) or temporarily with [6x2mm magnets](https://amzn.to/37Ihopq). Add [rubber feet](https://amzn.to/3LZv4v5) to keep the whole shebang from sliding, and [metal tire weights ](https://amzn.to/3uAzH9f)to drop the center of gravity and prevent wipeouts. You don't need to install every magnet, foot, and weight! Just use enough for your needs.

A Prusa i3 Mk3 can print up to a 5x5 grid. No matter what you use, make sure your bed adhesion and release is dialed in - these love to curl, and their high surface area can make them challenging to remove.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider plates can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity was inspired by Alexandre Chappel's ModuBOX system, which is found at https://www.alch.shop/shop/assortment

Gridfinity Baseplates

Weighted Baseplate 3x2.stl

Frame 1x4.stl

Frame 1x5.stl

Frame 1x6.stl

Frame 1x7.stl

Frame 2x2.stl

Frame 2x3.stl

Frame 1x2.stl

Frame 1x3.stl

Frame 2x7.stl

Frame 3x3.stl

Frame 3x4.stl

Frame 3x5.stl

Frame 3x6.stl

Frame 3x7.stl

Frame 4x4.stl

Frame 4x5.stl

Frame 4x6.stl

Frame 4x7.stl

Frame 5x5.stl

Frame 5x6.stl

Frame 5x7.stl

Frame 6x6.stl

Frame 6x7.stl

Frame 2x5.stl

Frame 2x6.stl

Weighted Baseplate 1x3.stl

Weighted Baseplate 1x4.stl

Weighted Baseplate 1x5.stl

Weighted Baseplate 1x6.stl

Weighted Baseplate 1x7.stl

Weighted Baseplate 2x2.stl

Weighted Baseplate 1x1 (super cute).stl

Weighted Baseplate 1x2.stl

Weighted Baseplate 2x4.stl

Weighted Baseplate 2x5.stl

Weighted Baseplate 3x6.stl

Weighted Baseplate 3x7.stl

Weighted Baseplate 4x4.stl

Weighted Baseplate 4x5.stl

Weighted Baseplate 4x6.stl

Weighted Baseplate 4x7.stl

Weighted Baseplate 5x5.stl

Weighted Baseplate 5x6.stl

Weighted Baseplate 5x7.stl

Weighted Baseplate 6x6.stl

Weighted Baseplate 6x7.stl

Weighted Baseplate 7x7.stl

Weighted Baseplate 2x7.stl

Weighted Baseplate 3x3.stl

Weighted Baseplate 3x4.stl

Weighted Baseplate 3x5.stl

This is a 2x1 **gridfinity** parts bin for **storing drill bits.**

I designed it for my small collection of masonry bits with a few spare places for expanding in the future.


**D.I.Y. TINKERER**
[https://www.youtube.com/c/diytinkerer](https://www.youtube.com/c/diytinkerer) - please visit my channel if you like this print :-) Thanks!

Gridfinity concept by [Zack Freedman](https://www.youtube.com/c/zackfreedman) 

Gridfinity 2x1 Vertical Drill Bit Holder(1).stl

A somewhat simple compartment to organize your quarter inch screwdriver bits. Fits up to 16, but I recommend storing 8 at most for quick access, or you'll end up fat fingering super hard when trying to reach the one you want

Gridfinity 16pcs ¼in Screwdriver Bit Holder 1x1x3.stl

A simple 2x5 design for the HOTO Precision Screwdriver kit. Wanted to keep the nice magnetic cover carrying case it came in, so designed one for it. Fits in an ikea Alex drawer.

Printed at 20% infill, 0.2mm layer height

Gridfinity Hoto Precision Screwdriver (Electric)

2x5 Gridfinity Hoto Precision Screwdriver.stl

Gridfinity

Activity related to collaborating with others on models

Likes, comments, and activity from your community

New content from your premium memberships

Emails and messages from designers you follow

Get notified when someone purchases your models or memberships

josefmistal

Achievements

Voyager

Seedling