Moto Morini 250 2c Carb to airbox rubber

Carburettor to airbox rubbers print in TPU. Join between carb and airbox rubber can be cut to size.

inlet airbox carb rubber with supports extended  v3 x115.stl

Onewheel XR Fender Spacers - Life Savers Compatible

XR_Fender_Spacer_No_Handle.stl

1985-90 Firebird Formula and Trans Am Aero Spoiler Wing Retainers

Retainer clips for 85-90 Firebird Formula and Trans Am equipped with the Aero Spoiler.

Print with ABS or something stronger. 6 pieces required.


D-Tool for Carburetor (Peugeot Kisbee)

F1 Tire Plant Pot

Tire valve cap- Heart 

Chinese Diesel Heater Muffler Collection

Chinese Diesel heater blower muffler

10th scale rc paddle tire

I designed this tire for snow, sand, and water. It is made for a 12 mm wheel hex and has an outer diameter of 10.5 centimeters to the tips of the paddles.

Tire Valve Cap and TPMS O-Ring

Garelli_rear engine mounts x4

Print in TPU (shore 95a a little too hard). Small mounts x 2 for front engine mount. Large x4 for rear

rear engine mounts x4 v2022.stl

Ignition plug for first gen Ford Bronco

Ignition plug for early Ford bronco.
A model I was commissioned to clone but never got paid for so here you go. 
Free for you to use, don't sell them or I'll kiss your dad on the mouth.

SUPORTE MICROFONES VOLANTE

SUP_MIC_VOL_P1.STL

spdway_leger_lite.STL

Solid tire for Minimotor Speedway leger / leger lite (and maybe more)

Printed in TPU:
4 walls / tops / bottoms
35% infill gyroid
support enabled

Printed @45mm/s with a biqu h2 (v1.0) with an 0.6mm nozzle.
The print took 33h 28m 27s !!!
And use almost 600g of filament !

I'm currently testing the new tire, I will update the description after few tests.

CrankShaft.stp

04.Esguicho_Motor_Shaft_Sleeve v1.step

TireBooster Mount to JoeBlow Track Pump

TireBooster_JoeBlow_TOP.3mf

Steering wheel center cap

Center cap for a steering wheel. I have used this as a template to make center caps with various logos, text, etc. 

Bolt pattern is 6 x 70mm. Holes are 5mm diameter.

Thule WingBar Profile

A replacement for the Thule Wing Bar rubber profile which might come loose and lost when driving at higher speeds.

The model is just updated to slide in easier, the standard length is just about 10cm so you need some to fully cover your bars.

Prints nicely in TPU95A standing upright with no supports, I recommend you use LostInTech's fine TPU cura profile (https://www.lostintech.co.uk/profiles/) to slice this particular model

vehicle parts & services

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Moto Morini 250 2c Carb to airbox rubber

Onewheel XR Fender Spacers - Life Savers Compatible

1985-90 Firebird Formula and Trans Am Aero Spoiler Wing Retainers

D-Tool for Carburetor (Peugeot Kisbee)

F1 Tire Plant Pot

View 22 new models

Chinese Diesel Heater Muffler Collection

10th scale rc paddle tire

View 23 new models

Garelli_rear engine mounts x4

Ignition plug for first gen Ford Bronco

SUPORTE MICROFONES VOLANTE

spdway_leger_lite.STL

CrankShaft.stp

View 22 new models

TireBooster Mount to JoeBlow Track Pump

Steering wheel center cap

Thule WingBar Profile

tire.obj

5speed transmission gearbox