Modular Filament Swatch (Sample) System

FilSwaSys 1v00b card.3mf

Hero Me Gen7 Release 4 ZIP

**This STL is an example of a completed Hero Me Gen7 printhead mounted to the X carriage of a 3D printer.**

Hero Me Gen7 is a modular printhead platform for 3D printers with excellent part cooling and the most compatibility across printers, hotends, extruders, ABLs, and other components.

 The Hero Me Gen7 is all about choice and personal preference. If you have been upgrading your 3D printer, you've made choices about what is important to you, Your choices are likely going to be different from everyone else. When choosing a hotend, extruder, and ABL combo (not to mention fans and accelerometers), where are you going to find a printhead platform that will accommodate all your selected components (which could be a rare combo), for your specific 3D printer AND provides part cooling that gives you great print results. **This is what the Hero Me Gen7 is all about!**

Think of the Hero Me platform as lego blocks for printheads, there are mounting parts for each component (hotend, extruder, fans, ABLs, etc.) that stack and mount to a core Base. Component specific mounting parts can be interchanged for another of the same type. So, should you change your component selection(s) in the future, you do not have to start over, you simple replace the single STL mount that is matched to the new component. There is no need to yet again go looking for a new set of mounting hardware that was not likely to have been designed to work with each other in the first place.

So to give you choice and fulfill your personal preferences in 3D printing, the Hero Me Gen7.3.2 now supports over 100 3D Printer models (plus clones), 46 Hotends, 34 Extruders (over 45 mount options), 17 ABL Sensors (34 mount options), 35 Part Cooling Duct options, 12 Cable Management options, 11 ADXL345 mounts, and 4 LED bar mounts (among many other options). Gen7.3.2 supports most of the popular 3D printers and components available. 

If you know your 3D printer model, hotend, fans, and optionally an extruder, ABL sensor, ADXL345 accelerometer (for Klipper), and any other options for your printhead assembly, you can scan through the Hero Me Gen7 Release 3.2 folder, or use the Thangs Advanced Search.  Be sure to set the creator filter to: ‘MediaMan3D’ then search for ‘HMG7’ which should bring up all the STLs. You can refine your search from there by component, brand, etc.

If you find that you have a 3D printer model or component that is not yet supported, send me information and preferably a STEP or STL (or link) if you know of one for the X carriage of that printer or the component and I will create a mount for it. Send to: **[MediaMan3D@gmail.com](mailto:MediaMan3D@gmail.com)**

The Hero Me Gen7.3.2 folder of STLs on Thangs is organized into sub-folders by component category, with sub—sub-folders for type and brand with well defined filenames to make it easy to find what you need. 

But If you want documentation to help you select and assemble the Hero Me Gen7 for your specific 3D printer, you can get a membership plan here on Thangs. 

by becoming a member you will get a detailed 56 page parts selection and illustrated assembly guide along with assembly videos, private Discord server access (with over 2,000 Hero Me users), technical support, and much more, You also get exclusive access to new STL releases 30 days before being posted to Thangs, and other STL libraries. Check out the membership plans here:  [https://thangs.com/designer/mediaman3d](https://thangs.com/designer/mediaman3d)

Hero Me Gen7 Example Model 1.stl

GEN2 Decor Filament Drawer - 185 (STANDARD)

prusaslicer-filament-chip-dividers.3mf

FuzzyRing (Easy Print .3mf) - Fuzzy Skin Sample *by RNDM3D*

FuzzyRing_0.8_v1.0_PRECONFIG.3mf

Variety Sampler

Base - x3.stl

GEN2 Filament Drawer - STANDARD

Drawer Stoppers.stl

GEN2 Classic Filament Drawer - 240-1W-05H

240-1W-05H Filament Classic Drawer.stl

Tippi Tree Test Piece

Here's the test piece for [Tippi Tree](https://than.gs/m/933018). You can use it to make sure your printer settings are well-tuned for printing your Tippi Tree without using too much time or material.


Recommended: PLA 0.4mm nozzle, 0.16mm layer height, 11% infill, 2 shells, 5 top/bottom layers

GEN2 Decor Filament Drawer - 240-1W-05H

240-1W-05H Decor Filament Sample Drawer.stl

Flexi Fila Swatch (filament samples made fun - flexible calibration)

Astronaut Head.stl

Microscope Slide Holder

A microscope slide holder for 26 x 76 x 1mm (1" x 3" x 3/64") microscope slides. It can hold up to 3 slides, makes comparing slides easier. Sometimes I have to check 20+ samples and also compare them at times. This helps me do it without swapping slides each and every time.

The microscope slide holder dimensions are:

86 x 128 x 3 mm

The slide holder fits on our Olympus inverted microscope with linear rail holders.

Infill percentage doesn't really matter, 100% will increase print time slightly compared to lower percentages. I did mine 100%.

Automated Water Sampling Carousel

1. Assembly.stl

Filament Samples and Box

Filament Sample.stl

Floppy Disk Filament Swatch

Floppy disk swatch.stl

COLOR SWATCH

SAMPLER.3mf

Tiny Spool

This tiny spool is really handy when you need to divide down a large spool so that many printers can use that filament at once or even just to use up small samples you may have.

The design prints without support and is press fitted together. Catches hold the two parts securely together. 

The inner diameter of the spool is designed to friction fit to the end of a drill to enable speedy spooling!

The STL files contain solid models but if you'd like the hexagonal pattern shown in the pictures use the 3mf files. They apply settings which make the first 2mm print without top or bottom layers and with 10 perimeter walls.

sample

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Modular Filament Swatch (Sample) System

Hero Me Gen7 Release 4 ZIP

GEN2 Decor Filament Drawer - 185 (STANDARD)

FuzzyRing (Easy Print .3mf) - Fuzzy Skin Sample by RNDM3D

Variety Sampler

GEN2 Filament Drawer - STANDARD

GEN2 Classic Filament Drawer - 240-1W-05H

Tippi Tree Test Piece

GEN2 Decor Filament Drawer - 240-1W-05H

Flexi Fila Swatch (filament samples made fun - flexible calibration)

Microscope Slide Holder

Automated Water Sampling Carousel

Filament Samples and Box

Floppy Disk Filament Swatch

COLOR SWATCH

Tiny Spool

Filament swatch

Microscope Sample/Slide Holder - Fixator edition