Corner brackets for simple square corner

HMG7.2 ADXL345 22.5mm Horizontal Mount.stl

This STL is a component of the Hero Me Gen7 Printhead assembly for 3D printers.

**Hero Me Gen7 is a modular printhead platform for 3D printers with excellent part cooling and the most compatibility across printers, hotends, extruders, ABLs, and other components.**


 The Hero Me Gen7 is all about choice and personal preference. If you have been upgrading your 3D printer, you've made choices about what is important to you, Your choices are likely going to be different from everyone else. When choosing a hotend, extruder, and ABL combo (not to mention fans and accelerometers), where are you going to find a printhead platform that will accommodate all your selected components (which could be a rare combo), for your specific 3D printer AND provides part cooling that gives you great print results. **This is what the Hero Me Gen7 is all about!**


Think of the Hero Me platform as lego blocks for printheads, there are mounting parts for each component (hotend, extruder, fans, ABLs, etc.) that stack and mount to a core Base. Component specific mounting parts can be interchanged for another of the same type. So, should you change your component selection(s) in the future, you do not have to start over, you simple replace the single STL mount that is matched to the new component. There is no need to yet again go looking for a new set of mounting hardware that was not likely to have been designed to work with each other in the first place.


So to give you choice and fulfill your personal preferences in 3D printing, the Hero Me Gen7.3.2 now supports over 100 3D Printer models (plus clones), 46 Hotends, 34 Extruders (over 45 mount options), 17 ABL Sensors (34 mount options), 35 Part Cooling Duct options, 12 Cable Management options, 11 ADXL345 mounts, and 4 LED bar mounts (among many other options). Gen7.3.2 supports most of the popular 3D printers and components available. 


If you know your 3D printer model, hotend, fans, and optionally an extruder, ABL sensor, ADXL345 accelerometer (for Klipper), and any other options for your printhead assembly, you can scan through the Hero Me Gen7 Release 3.2 folder, or use the Thangs Advanced Search.  Be sure to set the creator filter to: ‘MediaMan3D’ then search for ‘HMG7’ which should bring up all the STLs. You can refine your search from there by component, brand, etc.


If you find that you have a 3D printer model or component that is not yet supported, send me information and preferably a STEP or STL (or link) if you know of one for the X carriage of that printer or the component and I will create a mount for it. Send to: MediaMan3D@gmail.com


If you want Hero Me documentation… The Hero Me Gen7.3.2 folder of STLs on Thangs is organized into sub-folders by component category, with sub—sub-folders for type and brand with well defined filenames to make it easy to find what you need. If you want documentation to help you select and assemble the Hero Me Gen7 for your specific 3D printer, you can get a membership plan here on Thangs.  You will get a detailed 56 page parts selection and illustrated assembly guide along with assembly videos, private Discord server access (with over 2,000 Hero Me users), technical support, and much more, You also get exclusive access to new STL releases 30 days before being posted to Thangs, and other STL libraries. Check out the membership plans here:  [https://thangs.com/designer/mediaman3d](https://thangs.com/designer/mediaman3d)

Sharper Image Massage Gun Wall Mount

Sharper Image Massage Gun Wall Mount (v2) - Mount.stl

Creality Water Cooler Reservoir Bracket

Two of these brackets will hold a Creality Water Cooling Tank to the top of an Ender 3, or any other printer with a similar extruded aluminum bar, 

Corner bracket for 2020 section.stl

2x2 Corner bracket

WIP corner brace for outer corner bracket.

Ender5 Plus Brace

I made this brace for my E5P, but really it will work with any corner on aluminum extrusion that is compatible with the 2020 profile.

To attach them to my printer I used M5x16mm bolts and a t-slot nut like the ones found here: https://a.co/d/ajzrpvo . I used these so I could put them on my printer without having to take the whole thing apart.

Toolholder for ender bracket

tool holder .STL

Ring 4 Bracket (45 Degree)

Ring Bracket Right.stl

NEMA 17 Bracket

Has two holes for m5 screws that can be used to attach the bracket to V-Slot bar, using T nuts.

hd corner safety bracket v1.stl

I made this safety braket to secure a large cabinet to the wall so my boy wouldnt pull it on top of himself somehow.
it is 4.5'' on each angle side with .165'' holes for large deck screws

Anycubic Mega X LED Strip Mounting Brackets

RGB mount6.stl

fan ductL.3mf

fan duct for acrylic sunhokey prusa 3d printer. for 50x50 fan. left



Pi 4 water cooler mount v1.3.1.stl

Mount / Holder for water cooling block for rasberry pi 4b

[https://www.aliexpress.com/item/32810596518.html](https://www.aliexpress.com/item/32810596518.html)

Using it in my cyberdeck project
[https://hackaday.io/project/187632-skantdeck](https://hackaday.io/project/187632-skantdeck)

Shelves Brackets

shelf for bags p1.stl

Ten Top Opt Shelf Brackets

Top Opt Brackets Display Only Do Not Print.stl

Parametric Intel XF SR PCIe Bracket

intel_xf_sr_pci_bracket_dualport.stl

2-Way Parametric Shelf Bracket

This is a Parametric Shelf Bracket that can be used in either a classic underneath the shelf style or as an over the shelf hanging down style bracket (see pics). The parameters that can be accessed in Fusion 360 are:

Board Thickness: How thick is the board you plan to put in the slot for use in the 'over' style. A lumber yard 1x6 will measure approximately 18.5mm by 140mm due to sanding and facing losses. Enter 19mm in this case for a snug fit around a 1x6.

Board Width: As above a 1x6 will measure approximately 140mm wide. A 1x8 would be 191mm etc. The supplied model fits a standard 1x6 at 140mm. 

Bracket Thickness: How thick do you want the perimeters of the bracket to be? I've chosen 5mm which works well. This measurement drives some other measurements  so tinker at your own risk.

Bracket Height: The length of the "other side" of the bracket when used as an overhanging bracket. Ideally this should be as close to the width of the board as possible given the available height of the bracket. 120mm for a 1x6 is a nice compromise for using in both directions. 

Please enjoy!

 Intel Pro 1000 4 Port Full Height Bracket 

 Short Story Time. Had this card with a low profile bracket....didn't want to buy a full length bracket. 

The PCI-E Bracket is for the Intel Pro/1000 4 Port Ethernet card

This bracket is strong enough to plug and pull. Printing with PLA is fine, if you print in another material let me know please, would love to hear the results. 

Instructions to print 

    You must generate supports! If you are using Cura I recommend setting your print settings to advanced. 

    Support structure must be Tree
    Touching build plate
    the rest of the settings are up to you for supports (default worked for me)
    infill was set to 20% but that is only a recommendation*

    Let me and everyone know if any settings have better results.
    the hole is for a M3 insert. It is not entirely necessary to be screwed in but recommended 

PC Microphone Holder - Clip on to Newer Mic Holder

This is a mounting bracket to clip a PC Micorophone onto a Mic hlder made by Newer.

bracket

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Corner brackets for simple square corner

View 510 new models

Sharper Image Massage Gun Wall Mount

Creality Water Cooler Reservoir Bracket

Corner bracket for 2020 section.stl

2x2 Corner bracket

Ender5 Plus Brace

Toolholder for ender bracket

Ring 4 Bracket (45 Degree)

View 40 new models

hd corner safety bracket v1.stl

Anycubic Mega X LED Strip Mounting Brackets

View 40 new models

Pi 4 water cooler mount v1.3.1.stl

Shelves Brackets

Ten Top Opt Shelf Brackets

Parametric Intel XF SR PCIe Bracket

2-Way Parametric Shelf Bracket

Intel Pro 1000 4 Port Full Height Bracket

PC Microphone Holder - Clip on to Newer Mic Holder