Baby Rose Dragon

Cinderwing3D Baby_Rose_Dragon.stl

USB Cable organizer storage bin - Gridfinity

Cable storage bin with 10 18mm wide compartments, to fit various size USB or other cables. Fits USB cables up to 10ft length depending on diameter. Base is Gridfinity compatible 42mm squares (2x4), but top is not stackable.

Took about 12hrs to print in PLA on an Ender 5. No supports needed.

Bumbling Bee Articulated Fidget Bee - Keychain - Ludo 3D Printed Flexi

Bumbling Bee .stl

Tail Keychains

CoralTail.stl

6.25 mm - Quad Snaps (DS Part A) - Small Command Strip Mount

Quad Snaps (DS Part A) - Small Command Strip Mount.stl

Master Chief Bust - Halo (Pre-Supported)

MasterChief.stl

Totodile - Pokemon - Fan Art

Eagle - Wall Decoration

EAgle.stl

8x8 Legacy Tiles - 3x3 Board - Multi-Material Stack

8x8 Tiles - 3x3 Board - Multi-Material Stack.stl

Tray “waterdrop”

tray.stl

Tiny Egg Spider

Cinderwing3D Tiny Egg Spider_ColorEaster.3mf

Baby Koi Dragon

Cinderwing3D Baby Koi Dragon Colors Alt.3mf

Small Swamp - With Free Dragon  - 5e DnD Inspired for RPG and Wargamers

Swamp 7x4 Small.stl

Gemstone Tadling

gemstone-tadling-keychain.stl

Mini Print-in-Place Vise

**Print-in-Place Mini Vice**
This mini vise prints vertically as one piece using no supports. There are small pads on the moving jaws that reduce the clearance required in order to print it in place.  The risers under the vise allow the handwheel to be turned while sitting on a flat surface. The knob on the hand wheel should swivel as well.  The jaws are 64mm wide and  open to 80mm.  It has an overall printing height of 164mm.

**Print Instructions**
The moving jaws form on top of the serrations of the stationary jaw and as a result it’s important that you use a .4mm nozzle x .45mm line width, and .2mm layer heights if printing at 100%.  To free the jaws after printing I pried slightly with a screw driver on each side of the jaws before opening it with the screw.

The hardest thing about this print is probably the overhangs and bridging as a result of the weight saver holes.  If these hole are causing people issues I can make a version without them but I think most printers have adequate cooling to handle it. 

Printed on the [Muldex](https://github.com/3dprintingworld/MULDEX) rep-rap IDEX printer.

Printed with [3D Fuel Silver PLA]( https://www.3dfuel.com/collections/175ppla)


Print-in-Place Mini Vice

Cute Flexi Pets Pig (Keychain & Magnet)

Flexy pig_original.stl

Screw-On Cleat

Screw-On Cleat.stl

Type 1, Big Thread Holes, 2x2 Inside Bracket

Type 1, Big Thread Holes, 2x2 Inside Bracket.stl

Printer Health Check - quick print torture test

This is a quick print printer health check.
It takes just over half an hour to print.
It has overhangs, holes, curved recesses, strings, posts, thin walls and surface details and part of the base is one layer thick so that you can check first layer quality.

Print at 0.3mm layer height with the 'print thin lines' box checked

8x8 MU - Simple Bolt-Locked Shelf

4x4 Bolt-Locked Shelf.stl

R

Most Downloaded of All Time

Categories

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Baby Rose Dragon

USB Cable organizer storage bin - Gridfinity

Bumbling Bee Articulated Fidget Bee - Keychain - Ludo 3D Printed Flexi

Tail Keychains

6.25 mm - Quad Snaps (DS Part A) - Small Command Strip Mount

Master Chief Bust - Halo (Pre-Supported)

Totodile - Pokemon - Fan Art

Eagle - Wall Decoration

8x8 Legacy Tiles - 3x3 Board - Multi-Material Stack

Tray “waterdrop”

Tiny Egg Spider

Baby Koi Dragon

Small Swamp - With Free Dragon - 5e DnD Inspired for RPG and Wargamers

Gemstone Tadling

Mini Print-in-Place Vise

Cute Flexi Pets Pig (Keychain & Magnet)

Screw-On Cleat

Type 1, Big Thread Holes, 2x2 Inside Bracket

Printer Health Check - quick print torture test

8x8 MU - Simple Bolt-Locked Shelf