Print in Place Collapsible Jedi Lightsaber Concept 11

STL - Handle .stl

Ghost Pop Beads

These “Ghost Pop Beads” snap together to form spooky chains or rings as long as you want! Use for decoration or to accessorize your costume.

See here for video: https://youtu.be/sqHG2kSpsd8 

The pieces are designed to be printed in “Vase” or “Spiralized” mode. The file is optimized for printing with a 0.4mm nozzle. Printing with different nozzle sizes is still possible but will affect the tightness of fit.

Each piece uses approximately 0.4g of material, making this a great design to use up the scraps of filament you have lying around! A full 1kg roll could print approximately 2500 beads, enough to make a chain 50m (164ft) long!

To connect pieces together, simply pinch the bottom end of one piece to open it up. Insert the oval end of the second piece inside and release. The pieces remain connected but can be separated again if needed. Create long chains or rings by adding as many pieces as you want.

Each piece takes approximately 5 minutes to print. It is, however, much more efficient to print multiple pieces sequentially! Setting up spiralized models to print “one at a time” takes a bit of planning as the pieces must be spaced and sequenced properly so that the hot end or gantry does not collide with the finished prints as it moves on to the next print. 

Make the bottom open by setting “bottom layers” to zero. Good build plate adhesion is essential, so ensure that your machine is well calibrated.

This design is entered in the 2023 HalloweenWearable Contest

Similar Designs: 
Pop Bead Garland: https://social.thangs.com/m/513337 
Skull Pop Beads: https://than.gs/m/943349 


Tickler SA-6 — Fully 3D-printable semi-automatic airsoft pistol

Housing Right.stl

Cup of Teeth - Teacup

Dual Colour Teeth Cup - Teeth.stl

Skull Pop Beads

These “Skull Pop Beads” snap together to form spooky chains or rings as long as you want!

See here for video: https://youtu.be/pCv3Yx5U_7k 

The pieces are designed to be printed in “Vase” or “Spiralized” mode. The file is optimized for printing with a 0.4mm nozzle. Printing with different nozzle sizes is still possible but will affect the tightness of fit.

Each piece uses approximately 0.4g of material, making this a great design to use up the scraps of filament you have lying around! A full 1kg roll could print approximately 2500 beads, enough to make a chain 50m (164ft) long!

To connect pieces together, simply pinch the top end of one piece so that the opening becomes oval-shaped. Insert the oval end of the second piece inside and release. The pieces remain connected but can be separated again if needed. Create long chains or rings by adding as many pieces as you want.

Each piece takes approximately 5 minutes to print. It is, however, much more efficient to print multiple pieces sequentially! Setting up spiralized models to print “one at a time” takes a bit of planning as the pieces must be spaced and sequenced properly so that the hot end or gantry does not collide with the finished prints as it moves on to the next print. 

Make the bottom open by setting “bottom layers” to zero. Good build plate adhesion is essential, so ensure that your machine is well calibrated.

Similar Designs: 
Pop Bead Garland: https://social.thangs.com/m/513337 


CPX-2 Prop Gun v2.1 (+Prop Mag, Silencer +Custom Grips)

lowPolyCPX2_Gv2.stl

Slime Pack

Slime Oblong 1.stl

Predator Ceremonial Dagger

Hilt.stl

FREE Real-size Prop - Abyssal Dagger

ceremonial-dagger.stl

AC Valhalla Axe

Axe Head.stl

VTR-01 // Ballistic Missile Wall Art 

01 PIN.stl

Buster Sword

FF7_Bustersword_Crossguard.stl

Ahsoka Tano Lightsabers

Ahsoka Tano Lightsaber Long.stl

Zombie Hand (Pre-Supported)

Zombiehand.stl

1.5GB Tangle of 260 Spiderwebs (Loose Strand Density)

Spiderweb-Dia254-Sect24-Span12.stl

Llama potion bottle

kuzco.stl

Calice Della Morte

Here is the file for “Calice della Morte” (the Chalice of Death)

The Calice della morte is an ancient artifact that was created by a powerful sorcerer named Lucius Malvolio during the Dark Ages. 

He became obsessed with finding the secret of immortality and performed many experiments on human subjects, using dark magic and alchemy. He discovered that by mixing the blood of a pure-hearted person with a rare potion, he could create a liquid that would grant him eternal life. 

He poured this liquid into a chalice that he had carved from the wood of a magical tree the location of which is known only to Lucius himself he then enchanted the cup with various spells. 

He named it the Calice della morte, as he believed that it would allow him to conquer death itself.

I printed mine in Fillamentum Timberfill Light Wood on my Prusa Mk3 with a 0.8mm nozzle with 0.5mm infill and zero support, 

I then gave it a sanding up with 180 grit before weathering with some coffee alcohol ink diluted with isopropyl, i then gave it a second sanding with 240 grit to re lighten the highpoints.

though if you wanted to print in plastic i would try dry brushing the model for a similar effect

I hope you enjoy, and Happy Halloween

Thanks

Bugman

If you like what I am doing please consider buying me a coffee or tipping.

https://www.buymeacoffee.com/bugman140

Prop

Most Downloaded of All Time

Categories

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Print in Place Collapsible Jedi Lightsaber Concept 11

Ghost Pop Beads

Tickler SA-6 — Fully 3D-printable semi-automatic airsoft pistol

Cup of Teeth - Teacup

Skull Pop Beads

CPX-2 Prop Gun v2.1 (+Prop Mag, Silencer +Custom Grips)

Slime Pack

Predator Ceremonial Dagger

FREE Real-size Prop - Abyssal Dagger

AC Valhalla Axe

VTR-01 // Ballistic Missile Wall Art

Buster Sword

Ahsoka Tano Lightsabers

Zombie Hand (Pre-Supported)

1.5GB Tangle of 260 Spiderwebs (Loose Strand Density)

Llama potion bottle

Calice Della Morte

Real-size Prop - Spectre’s Lantern

Working Create Mod Wrench

Batarang Ornaments - Batman - Christmas Day 12