Spiral Snow Man Tree Ornament

H2_Duct_BX_Version.stl

Luke (looxonline) 
https://www.thingiverse.com/thing:4864920
remixed the original from 
Phil (fhogphil)
https://www.thingiverse.com/thing:4789656

I just needed it to be 2mm further to the right to fit my H2. Perhaps my heatblock is rotated 180°.
Anyways, here it is, offset to the right by 2mm.

DuPont Wires Adapter(2×5)

Prusa-i3-MK3S+ Y Axis right shaft End Stop Bumper 36.2mm upgrade

**Prusa i3 MK3S & S+** the zero end stop setup is by forcing the X & Y carriage against the frame.

On the Y axis, only the left shaft bearing is abutting against the frame, with the belt in the centre of the bed, it is forcing sideways the whole plate at each startup. By doing this, it slowly bring some play into the bearings and plate increasing noise and play, what all users are facing after printing a few dozen hours.

To improve this excessive force onto the left bearing, adding a buffer on the right bearing to have a flat contact of the Y plate should reduce this unwanted lateral effort on the bearings.

This easy upgrade only works when installed on a new machine, or revised Y bed bearing axis.

Size of the bumper varies from one machine to another. Between two original Prusa machines, I have values for the bumper from 34mm to 36.5mm, check yours! 

One is 44 days print time, and the other one is 7 days print time. Play and noise of the 44 days printer is high and not pleasant.

Once your bumper installed, pushing the bed all the way back, the bed should not be able to move more on one side than the other. If it does, **check the length of your bumper and adapt it accordingly**.

Swiss3Dc Prusa-i3-MKS+ Y Axis right shaft Bumper 36.2mm upgrade

3D Printed Queen Box (Optimized)

Used to transport a single queen bee. Sugar paste is placed in the hole at the end of the cage and allowed to dry before use. Once the queen is place inside, the lid is pressed in place and the four small posts are smashed down with a hot object to permanently seal the cage.

Ornate Baroque Desk Organizer - Victorian Office Caddy with Phone Stand & Sticky Note Holder

Borg3.stl

Aesthetic Tuxedo & Bow Makeup Organizer - 3D Printed Vanity Brush Holder

GirlSuitOrg.stl

Sliding lamp

Logitech Streamcam Mount with Joint (Remix)

Yet another flux Dispenser

Candy Helicopter with Movements

XT90 Plug Safety Cover

desk organizer box .stl

Phone holder with gears - Without supports

Modular Desk Organizer

Drawer.stl

LATIN SMALL LETTER T, nestable box (v1)

LATIN CAPITAL LETTER C, nestable box (v1)

LATIN CAPITAL LETTER Q, nestable box (v1)

HP LaserJet 100 color MFP M175 back door lock bracket

One time I open the back door and this part fell out. Then I lost the part.
Without this part, the back door can not close properly, and it will not print because it thinks the door is open.
Thankfully I have another identical printer, and I made a model of the bracket (for the left side). The printer works just fine now with this replacement part.

Hexagonal, nestable box (v1)

Office supplies

Most Downloaded of All Time

Categories

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Spiral Snow Man Tree Ornament

H2_Duct_BX_Version.stl

DuPont Wires Adapter(2×5)

Prusa-i3-MK3S+ Y Axis right shaft End Stop Bumper 36.2mm upgrade

3D Printed Queen Box (Optimized)

Ornate Baroque Desk Organizer - Victorian Office Caddy with Phone Stand & Sticky Note Holder

Aesthetic Tuxedo & Bow Makeup Organizer - 3D Printed Vanity Brush Holder

Sliding lamp

Logitech Streamcam Mount with Joint (Remix)

Yet another flux Dispenser

Candy Helicopter with Movements

XT90 Plug Safety Cover

desk organizer box .stl

Phone holder with gears - Without supports

Modular Desk Organizer

LATIN SMALL LETTER T, nestable box (v1)

LATIN CAPITAL LETTER C, nestable box (v1)

LATIN CAPITAL LETTER Q, nestable box (v1)

HP LaserJet 100 color MFP M175 back door lock bracket

Hexagonal, nestable box (v1)