Printception Large Vase

large-vase.stl

Circular Hygrometer snap on 2020 extrusion

Since I did a design for the rectangular hygrometer, I thought it was not much more effort to do for a circular version.

Print in place with no supports, no additional mounting hardware required.

Orientate however you like!
*****
Want to buy me a coffee?
https://www.buymeacoffee.com/zer0s

Clicking on my affiliate links below will give me a small kickback if you purchase something. (at no extra cost to you)

AliExpress affiliate link:
Hygrometer Thermometer
https://s.click.aliexpress.com/e/_DlQxosf

*****
Consolidated affiliate links of other 3D printing-related items:
https://wp.me/peMLu6-j

For Amazon affiliate links
https://wp.me/peMLu6-2C

Rectangular Hygrometer snap on 2020 extrusion

Simple bracket to snap on hygrometer to any 2020 extrusion.

*****
Want to buy me a coffee?
https://www.buymeacoffee.com/zer0s

Clicking on my affiliate links below will give me a small kickback if you purchase something. (at no extra cost to you)

AliExpress affiliate link:
https://s.click.aliexpress.com/e/_DeAZr9P

******
Consolidated affiliate links of other 3D printing-related items:
https://wp.me/peMLu6-j

For Amazon affiliate links
https://wp.me/peMLu6-2C

Printception Square Container

square-dish.stl

Manual Filament Feeder Extruder Gear Knob Mod for CR-10 and other Bowden 3D Printers

extruderknob-v2.stl

Creality K1 Extruder motor heat shield with air vents

K1 - ExtruderHeatShieldVented.stl

Creality K1 Extruder motor heat shield

K1 - ExtruderHeatSheild.stl

2020 Extrusion - Pivot/Hinge - Midspan

2020 Tee Connector - 4way - Full

2020 Extrusion 4-way Tee

2020 Extrusion - 3-way Tee

2020 Extrusion Pivot/Hinge - 90deg

2020 Extrusion Pivot/Hinge

Corner Bracket for 2020 Square Corner

Extrusion Mount Spool Holders

2020Arms.stl

Flush Cutter Holder for 20x20 Extrusion, Ender 3

flush cutter holder rounded edges.STL

Fanatec SQ1.5 4040 Aluminium Mount Bracket.stl

**Fanatec SQ1.5**
_4040 Aluminium Mount Bracket_

Existing solutions available on the market either put the shifter too far away, too close, or encroached into the seated area of the rig. These brackets put the shifter directly over the 4040 extrusion. 

You'll need to print two - one for the front and one back. Should slide nicely onto a bit of extrusion with a width of 40mm. Print with the two prongs facing upward - no supports should be necessary.

**Other hardware required:**
* 4 M6 x 20mm bolts with head diameter of less than 12mm to hold the brackets to the shifter. The 20mm is important here to ensure that the screws don't go more than 15mm into the shifter, as per the Fanatec drilling guide for the unit.
* 4 M8 x 20mm socket cap bolts to attach brackets to profile.
* 4 M8 Slide nuts.


**This is for a 0.4mm nozzle, adjust as appropriate to your printer:**

* Increase the number of walls to 8, this creates a solid block where the bolts connect to the shifter
* If possible in your slicer, set the infill or number of walls in such a way that it creates a solid (100% infill) for the holes that the bolts go through for the profile.

These settings ensure you can tighten up the bolts plenty, without risk of crushing the plastic easily.

Extrusion

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

View 78 new models

Circular Hygrometer snap on 2020 extrusion

Rectangular Hygrometer snap on 2020 extrusion

View 72 new models

Manual Filament Feeder Extruder Gear Knob Mod for CR-10 and other Bowden 3D Printers

Creality K1 Extruder motor heat shield with air vents

Creality K1 Extruder motor heat shield

2020 Extrusion - Pivot/Hinge - Midspan

2020 Tee Connector - 4way - Full

2020 Extrusion 4-way Tee

2020 Extrusion - 3-way Tee

2020 Extrusion Pivot/Hinge - 90deg

2020 Extrusion Pivot/Hinge

Corner Bracket for 2020 Square Corner

Extrusion Mount Spool Holders

Flush Cutter Holder for 20x20 Extrusion, Ender 3

Fanatec SQ1.5 4040 Aluminium Mount Bracket.stl