Tens 2X2 Pad Holder Tray

Tens2X2PadHolderV1.stl

Hoover Air Lift Pet Vacuum Top Handle UH72511

HooverVacHandleV1.stl

SentrySafe Cabinet Desiccant Tray

DesiccantTray.stl

Newair AI-100SS Drain Cap and Plug

Cap.stl

ES8266 D1 Mini 12VDC Garage Door Controller/Relay

GarageDoorController_BasePlate.stl

Paracord or String Spool

ConcaveParacordSpool.stl

Guy Line 550 Paracord Fastener

Based on an old model I printed years ago and now cannot find, I decided to recreate it from scratch with some optimizations of my own.

Cable Entry Seal

This is a 30mm long bushing (meant to be printed in TPU or flexible filament). The center diameter is 5mm and the outside diameter is 24mm. This is a perfect solution to plug the large holes required for Amcrest, Dahua, Hikvision, Uniview, and other manufacturers which use a water resistant cable cover assembly.

Drill your hole, insert everything, then feed this bushing onto the cable and stuff it into the hole. The bushing is slightly larger than a 7/8" drill hole (the size required to fit a cable head cover). As you fit it into the hole, it will squeeze the cable as well and seal up.

Kobra Max Lifecam 5000 Mount

MicrosoftCameraMount_45.stl

Anycubic Kobra Max SKR 3 EZ Adapter

SKR3_KobraMax_Mount.stl

Top mount Filament Sensor - fits Kobra Max and others

Kobra Max Top Mount Sensor Bracket.stl

Creality Sprite Volcano 5015 Fan Duct

High-Flow Modular 5015 cooling duct sprite extruder with Touch spacer VOLCANO.stl

Extrusion Mount Spool Holders

2020Arms.stl

PETLIBRO Pet Food Funnel

A funnel made to fit the PETLIBRO 5L automatic pet feeder. Filling it is messy and annoying, so I put a stop to that.

Print it in vase mode with 0.6 line width for a fast and easy print.

OrangePi Zero 2 Case w/ Fan and 2040 Extrusion Mount

OrangePiZero2_Case_FanShrouds.3mf

Kobra Max ADXL345

A quick mount I made for the Anycubic Kobra Max to put an Adafruit ADXL345 in place.

TPU Bed Screw Washers

Drop these washers between the bed screw and bed. Print with TPU for some grip. This will stop your screws from spinning without using glue/epoxy or making the surfaces rough with sand paper.

Print at 0.4 height with an 0.8 nozzle and these will be done in seconds.

Planter Marker for 0.8 Nozzle

0.64mm high planter marker (2 layers at draft quality). This was designed to be printed with an 0.8mm nozzle quickly. Allow to fully cool before removing from bed to eliminate warping.

Ender 3 Gantry Level Hook

A hook to level the Ender 3 (Pro) gantry. Raise Z to ~225 or so, slide the hook over the top and into the backside of the gantry. Lower it down until the gantry is forced straight on the hooks. You are now parallel with the top frame.

If you have dual-z motors, they are now level once you've heard them bind up and stop. If you are on belted dual-z, you'll have to take one of the cogs loose, force the gantry down onto the leveling hooks, and then tighten the cog into place. Tighten the belt before letting go of the gantry so it can't spring back up.

Rack Screw Washer

Bushing for large rack screws that use cage nuts.

Rack Screw Bushing

Print-in-Place Adafruit ADXL345 Bed Mount

Print in center of bed with brim, 50% infill, no supports. Screw the ADXL345 into place using (2) M3-6 screws. Land your wires and run your Input Shaper test.

Creality Sprite ADXL345 Mount

Adafruit ADXL345 mount for the Creality Sprite Pro Upgrade Kit. You will need an Adafruit ADXL345 and (3) M3-6 screws.

ryanpie86

Achievements

Seedling

Explorer

Up and Coming