Ender 3 light bar

ender 3 LED side mount WITH SPOOLHOLDER.stl

3D Printer Filament Duster

A clip-on fliment duster to ensure no dust makes it into the hotend on the filament.  Prints in place with a live hinge and friction clamp.  

You get better quality if you print this open-side-up, due to the latch. Also I highly recommend enabling top layer ironing as it makes the hinge a little bit stronger.

Filament Duster

3D Printer Bed Leveling Test

A wider bed leveling test designed for the ender 3, but will work for any printer, just scale it in x and y.

Timelapse Rig (Ender 3 and similar printers)

flexible-finger.stl

Ender 3 Nozzle Wipe Mounting Bracket

Ender 3 Under Bed Wipe Mount Mk.2 Bolted.STL

Professional Ender 3v2 Drawer Knob

Drawer Knob for the Ender 3v2. Knurled style matching my other Ender 3v2 Knobs linked below.  

WARNING: This is a delicate knob to replace. If the tabs breaks, try another/stronger filament.

Installation:  Remove drawer, press tabs inward to remove OEM drawer, gently push in new knob. Tabs can be delicate, I used Polymax PLA, but most strong filaments will work, just be gentle with install.

Batman Extruder Knob Ender 3

 made this for my Ender 3 V2 Neo but it might work on other versions of the Ender 3

Ender 3 Filament Spool Retainer

This cap clips onto the spool holder to prevent spools from somehow finding their way off of the holder and onto the print bed.  I didn't think this was an issue but alas the ender has proved me wrong lol.  The outer diameter of this thing is just big enough that no spool should be able to make it over.  

T-nut endstop mount for Creality limit switch from Ender 3

Minimalistic mount to place the Creality limit switch (seen for instance in the Ender 3) on top of a T-slot profile.

Bill of materials:

2 x M3 T-nut
1 x FHCS M3x6 (screw inside T-nut)
1 x SBHC M3x10 (screw inside T-nut)
1 x SBHC M3x6 (screw directly into the mount)

Industrial - 4 High Damaged

A damaged version of our 4 high building. Built for FDM.

Suggested print at 120 microns and requires supports - organic recommended.

Ender 3 S1 print time is around 5-6 hrs on quality setting.

Giant No. 2 Pencil Box & Stash Container

Whole Pencil Box Back to School.stl

Industrial Mid - Damaged

Damaged Version of the Mid building in the Industrial Set. 6mm scale | 1:265 scale style building for Battletech/Epic40k/Titanicus etc.

Keychain model 1 

----- RESIN PRINTABLE -----
A 3D model of a keychain typically represents a small decorative or functional object that is designed to hold keys. most of my keychains will print with Plastic as well a resin printers.

Ender 3 spool holder.stl

new ender 3 filament holder.stl

Creality E-Fit 5015 Cooling Fan Adapter

I created this adapter to mount a 5015 to the E-fit direct drive extruder kit from Creality.

Prints with no supports and very little filament. Use the existing bolts in the kit to mount the adapter then use M3 bolts to mount the fan to the adapter.

This is tested and works but I am no fluid dynamics expert.

Show me yours if you print one!

@kwerkshop on Instagram

Creality Ender 3 Max power supply reallocator

Meanwell Power Supply.stl

Lie Flat Spool Holder (with bearing)

HMG7.3 HyperCube-BLV Style Box X Carriage Tall Back.stl

This STL is a component of the Hero Me Gen7 Printhead assembly for 3D printers.

**Hero Me Gen7 is a modular printhead platform for 3D printers with excellent part cooling and the most compatibility across printers, hotends, extruders, ABLs, and other components.**

 The Hero Me Gen7 is all about choice and personal preference. If you have been upgrading your 3D printer, you've made choices about what is important to you, Your choices are likely going to be different from everyone else. When choosing a hotend, extruder, and ABL combo (not to mention fans and accelerometers), where are you going to find a printhead platform that will accommodate all your selected components (which could be a rare combo), for your specific 3D printer AND provides part cooling that gives you great print results. **This is what the Hero Me Gen7 is all about!**

Think of the Hero Me platform as lego blocks for printheads, there are mounting parts for each component (hotend, extruder, fans, ABLs, etc.) that stack and mount to a core Base. Component specific mounting parts can be interchanged for another of the same type. So, should you change your component selection(s) in the future, you do not have to start over, you simple replace the single STL mount that is matched to the new component. There is no need to yet again go looking for a new set of mounting hardware that was not likely to have been designed to work with each other in the first place.

So to give you choice and fulfill your personal preferences in 3D printing, the Hero Me Gen7.3.2 now supports over 100 3D Printer models (plus clones), 46 Hotends, 34 Extruders (over 45 mount options), 17 ABL Sensors (34 mount options), 35 Part Cooling Duct options, 12 Cable Management options, 11 ADXL345 mounts, and 4 LED bar mounts (among many other options). Gen7.3.2 supports most of the popular 3D printers and components available. 

If you know your 3D printer model, hotend, fans, and optionally an extruder, ABL sensor, ADXL345 accelerometer (for Klipper), and any other options for your printhead assembly, you can scan through the Hero Me Gen7 Release 3.2 folder, or use the Thangs Advanced Search.  Be sure to set the creator filter to: ‘MediaMan3D’ then search for ‘HMG7’ which should bring up all the STLs. You can refine your search from there by component, brand, etc.

If you find that you have a 3D printer model or component that is not yet supported, send me information and preferably a STEP or STL (or link) if you know of one for the X carriage of that printer or the component and I will create a mount for it. Send to: MediaMan3D@gmail.com

If you want Hero Me documentation… The Hero Me Gen7.3.2 folder of STLs on Thangs is organized into sub-folders by component category, with sub—sub-folders for type and brand with well defined filenames to make it easy to find what you need. If you want documentation to help you select and assemble the Hero Me Gen7 for your specific 3D printer, you can get a membership plan here on Thangs.  You will get a detailed 56 page parts selection and illustrated assembly guide along with assembly videos, private Discord server access (with over 2,000 Hero Me users), technical support, and much more, You also get exclusive access to new STL releases 30 days before being posted to Thangs, and other STL libraries. Check out the membership plans here:  [https://thangs.com/designer/mediaman3d](https://thangs.com/designer/mediaman3d)

Creality Water Cooler Reservoir Bracket

Two of these brackets will hold a Creality Water Cooling Tank to the top of an Ender 3, or any other printer with a similar extruded aluminum bar, 

2023 - Ender 3 Board fan silencer/guard

I was fond of the original design(https://www.thingiverse.com/thing:2935204), but it didn't address the noise issue. That's why I designed a new motherboard fan guard/silencer that significantly reduces the noise level while while bearly affecting the cooling for the motherboard. The difference in sound is clearly audible.

The STL file will be blank and will not have my logo on it

Ender 3

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Ender 3 light bar

3D Printer Filament Duster

3D Printer Bed Leveling Test

View 111 new models

Ender 3 Nozzle Wipe Mounting Bracket

View 14 new models

Batman Extruder Knob Ender 3

Ender 3 Filament Spool Retainer

T-nut endstop mount for Creality limit switch from Ender 3

Industrial - 4 High Damaged

Giant No. 2 Pencil Box & Stash Container

Industrial Mid - Damaged

Keychain model 1

Ender 3 spool holder.stl

Creality E-Fit 5015 Cooling Fan Adapter

Creality Ender 3 Max power supply reallocator

View 10 new models

View 510 new models

Creality Water Cooler Reservoir Bracket

2023 - Ender 3 Board fan silencer/guard