Wearable Iron Man Mark 85 Helmet

The jaw is removable and there are cutouts where you can put magnets in both the jaw and the helmet for a better fit.

New updated model. Some had problem printing some of the parts from the earlier model. Let me know if the problem remains for some of you if that's the case.

STL-files for 3D-printing.

Scaled to size.

STEP file included.

Check out my other models at: https://thangs.com/designer/Mattias%20Hellberg

Iron Man Helmet

Mk85.STEP

Please "like" this thing to help it rise in the search results, especially if you download it or add it to a collection.

It's a threaded dragon egg, great for Easter egg hunts, gifts, and Game of Thrones fans.

The whole egg measures 63mm tall by 45mm wide. I will soon add large and extra large versions.

This is a remix of my own threaded Easter egg. I made every bit of this from scratch, including the scales. I made the scales by importing a custom texture into a Blender brush and placing every scale one at a time, adjusting the size as I went. I designed it with Sketchup, Blender, and Meshmixer. (And Gimp for the scale alpha.)

If you like this design and want to show your support, you can share your make, leave a review, or buy me a coffee (via [Paypal](https://www.paypal.me/tonyyoungblood), [Venmo](https://www.venmo.com/u/Tony-Youngblood), or [CashApp](https://cash.app/$TonySYoungblood)). I appreciate 
you.

Instructions:

1. Print the bottom and top pieces as oriented in the files. Supports are not required. I recommend a layer height of 0.2mm or smaller, wall thickness of 1.2mm, a bottom thickness of 0.6mm, and a top thickness of 0.8mm. Infill density of 12 percent or higher. I tried to allow for horizontal expansion in the design, so first try printing it without adjusting horizontal expansion, slicing tolerance,  or x/y compensation. If it prints too tight or too loose, then you can use one of those slicing features to compensate. Threads are notorious for being the hardest item to print, so please be patient. If you want to save time while testing, you can print the included calibration test instead of the full model. 
2. Once printed, screw the threads in and out repeatedly to remove any stray particles. It may feel too tight on the first threading but should screw easily after ten seconds of doing this.    
3. Note the small nubs near the threads. Refer to the pictures to see what I'm talking about.  When the two nubs are parallel, you know you've got the proper alignment.

Licensed under Creative Commons Attribution Share Alike. If you sell prints of this file, please respect the license and credit me on the sales page with a link to this page.

Threaded Dragon Egg, Great for Easter and Gifts

DragonEggStandardBottom.stl

Iron Man Helmet.STEP

This dual-color cracked skull design can be printed with translucent filament to let light shine through the cracks! 

See here for video: https://youtu.be/uCC3UsVzpis 


Cracked Skull

Skull.stl

Pokéball with a working hinge

STL-files for 3D-printing

Regular Pokéballs can be downloaded at: 
https://thangs.com/designer/Mattias%20Hellberg/3d-model/Pok%C3%A9mon%20Balls-12533?manualModelView=true

Check out my other models at:
https://thangs.com/mattias.hellberg.95

Pokeball With Hinge

Pokemon Ball.STEP

License: Attribution-NonCommercial-NoDerivs
CC BY-NC-ND
***
***Sculpt by Garrett***

**_A fun "Springy" sculpt for #MakerMadness_**

***
If you would like to support us and receive exclusive to Patron models every month check us out here:
https://www.patreon.com/chaoscoretech

***If you would like to sell physical objects, please see the Chaos Core Partner tier on our Patreon***

R2D2 Egg Container

R2D2Egg_Whole.stl

PLA & Resin 3D Printable Model
STL File Available
Check the attached image for reference 

Very minimal time is required to print this keychain
Print in Resin for better Detailing 

Ironman Keychain 3D Printable

iRONMAN Keychain.STEP

STL-files for 3D-printing

Wearable Iron Man helmet Mark 3

Faceplate that can open and close with arms. Arms Can be downloaded at the older version: https://thangs.com/designer/Mattias%20Hellberg/3d-model/Iron%20Man%20MK3%20-27353?manualModelView=true

I have seen some people uploading this model and they have not included the STL files. So I upload this again for the new people on the site so you have the STL files too. I have also made the STL quality higher

Iron Man

Iron Man mk3.STEP

An elegant holiday decoration created by overlapping diamond patterns over a basic ball with stem. The ornament is printed as a single piece. It requires some infill, but only in certain places.

The ornament prints very well with the standard 0.4mm nozzle but prints even better with a 0.25 nozzle.

I've provided my PrusaSlicer 3mf file (for 0.4mm nozzle), which includes all the height adjustments to minimize weight while providing the necessary top, bottom, and infill needed for a beautiful print. Some supports are needed, but not a lot. I used organic supports.

I included GCODE in my 3MF file to reduce the nozzle temp at key places to avoid having the filament overheat. The nozzle starts at 200c and decreases at key points down to 180c. You may need to adjust these based on your filament.

The filament shown is MatterHackers Quantum Purple Gold. The design will look good in a variety of filaments, from single color silky or glitter filaments to rainbow and 2 or 3 color filaments.

Have fun and if you like how it turns out, please post a make.

Happy holidays!

Christmas Ball with Intersecting Diamonds

Quad Four Point Diamond Ball Final.stl

These vintage-style ornaments are designed for spiralized printing to maximize translucency and minimize material and print time. Download includes six different mix-and-match styles!

See here for video: https://youtu.be/JIcOVe_VUuc 

 More Spiralized Ornaments:
Vintage: https://than.gs/m/964487 
Textured: 

When printed with a 0.4mm nozzle, each ornament requires less than 8g of material. You could print over 125 ornaments with 1kg of filament! A great way to get the most out of your specialty (expensive!) filaments.

For each ornament, you will need to print out a “top” and “Bottom” file. Be sure to use “spiralized” or “vase” mode! You will need to open up the hole in the top by trimming the inside protrusion with a pair of clippers. See video for demo.

Here are some recommendations for spiralized printing:
- Use thick layer heights, 0.2mm or greater
- Set your “Bottom Layer” to 1
- Try using a skirt for bed adhesion, but if that is not working then try a brim. You will just have to remove the brim afterwards
- If you get funny stringing on the top layer, try moving the z-seam alignment around


Spiralized Ornaments - Textured

Hex Top.stl

Snap two pieces together to make a ball. Stick some bells or treats inside. My cat hated them no matter what I did. Maybe you’ll have better luck.

See here for video: https://youtu.be/nEKON9TpzeI 

There are three interchangeable surface style options. If you want the ball to be all the same surface style just print two of whatever surface you prefer. This model is designed for resin printing.

This design is sponsored by Resins3D. Models shown are printed on an Elegoo Saturn 2 with Elegoo Space Grey resin.


Cat Toys

Cat Toy Gyroid.stl

Plasti-Bowl | Desktop Lane Toy

Lane.stl

Lane_A.stl

Lane_B.stl

- Supports Are Needed.
- The G-code File Includes Supports .
- You Can Resize The Model By Remix It / or on Your Slicer.

3D Design Ball In Dice Fidget Toy.

Just what you need for a little game of b-ball!

See here for video: https://youtu.be/sNO8MSMIYjA

Files for this basketball and hoop set are provided for standard and multicolour printing. Print all files as oriented, no supports needed. 

The backboard has holes for hooks or magnets (1/4”x1/8” or 6mmx3mm neodymium). The line on the backboard is raised slightly in the standard print version to allow for a filament swap to make the line a different colour.

The halves of the balls are designed to be tight the first few times they snap together. To make them easier to snap together and apart simply file off a bit of the contact surfaces. For single colour prints you can colour the seam with a marker.

Download the full set:
Basketball: https://than.gs/m/833255 
Hoop: https://than.gs/m/833259 
Backboard: https://than.gs/m/833268 

Model in picture was printed on a Snapmaker J1 in white and orange.



Basket Smalls (Basketball)

Display only do not print.stl

This Woven Ball is impossible to print. Unless you use water soluble PVA filament for supports!

See here for video: https://youtu.be/o5lJ5TMQRpk

The top inside of the ball has overhangs that need to be supported or the print will fail. Typical supports can’t be use because the holes are too small to allow removal of supports from inside the ball. With PVA filament, you can use all the supports you need, soak the finished print in warm water, and watch the supports simply dissolve away!

This model printed with my Snapmaker J1 IDEX printer using Snapmaker PVA filament and Sunlu White PLA.


Woven Ball

Woven Ball.stl

Storage for small products
Like, Memorycard, Pendrive Etc.

Pokemon Pokeball
 

Pokeball Storage 

Pokeball.STEP

ball soccer shaped capsule for multicolor printing

recommended parameters:
-wall 3 - 4
-supports 60°
-infill 20%

Soccer Football Ball Capsule

Upper part.stl

3D Printable Dragon Ring 

License: Attribution-NonCommercial-NoDerivs
CC BY-NC-ND

Dragon Ring V2 (3D Print Model)

Dragon Ring v2.STL

These pieces snap together to form a spherical truncated icosahedron, a shape recognizable as a football or soccer ball. 

See here for video: https://youtu.be/C-KsbcPzaH4 

In the model shown, the “Penta” pieces are printed in black, the “Hex” pieces are printed in white. A complete ball requires 20 of the “Hex” pieces and 12 of the “Penta” pieces. The files provided will create a ball that is 100mm in diameter.

This design minimizes that amount of material needed to print large spheres, and also allows for multicolour balls by printing pieces in different colours.  You do not need supports to print, but you will need to ensure good bed adhesion. 

The pieces hold together on their own and will not need glue.

When assembling, be aware that the connection tabs on the hexagonal pieces are different depending on whether that side is connecting to another hexagonal piece or a pentagonal piece.

Pentagonal pieces only ever connect to hexagonal pieces, so the pentagonal tabs are all the same.

The tolerance between pieces is intentionally tight and will require some force to assemble. You can loosen the fit by filing of the thicker bottom layer “elephant foot” on each piece, or by scaling up the pieces slightly to increase the space between.  Be sure to do a few small test prints first before printing a whole batch.


Snap Ball (Truncated Icosahedron) 

Snap Ball Display.stl

Hello! I just wanna wish everyone a Merry Christmas and a early Happy new year! And may the force be with you!! 

Slice the death star and glue it together or just print it in one piece! 

Ball

Most Popular of All Time

Categories

Popular

Personalize

Trending