Wii-Tar DIY Adapter Case

Case.stl

GT Omega Cockpit Sim Racing Rig Adapter For Beavis Racing Shifter and Handbrake

This is an adapter plate used to attach the 3D Printed Beavis Racing sequential shifter and a handbrake to the small mount included on GT Omega brand sim rig frames. This plate will likely work for a variety of other cheap sim racing rigs including brands like Minneer, Vevor, Marada and Anman

Simple hose adapter for shop vac.

Single 45 RPM Adapter

Bambu X1C Vent Adapter

I wanted to vent the exhaust from my Bambu Labs X1C through a filter then outside. The original model would not work without modification. The other remixes were close, but not quite what I was looking for. 

Print times are roughly 3hr on normal, and 1.5hr on ludicrous.

MicroSD Card holder v2

Power Wheels Battery Adapter

Power Wheels Back Wheel adapter

Its for the back wheels of power wheels , it can be use as the suspenssion lowering blocks

Starter Adapter

Transaxle.24-2010 v18.3mf

18650 BATTERY ADAPTER FOR XML-T6 TACTICAL FLASHLIGHT

Rear button is loose and malfunctioning using my repurpose 18650 from old laptop battery with stock 18650 battery adapter.

This adapter is longer than stock and keeps the rear button fix working flawlessly with any 18650 in the T6 flashlight.

2x7 WallControl to 1x4 Gridfinity Adapter

I combined a few model's geometry to make a 5 part assembly into a single part.

https://thangs.com/designer/notsam/3d-model/2x7%20WallControl%20to%201x4%20Gridfinity%20Adapter-63060

https://github.com/aderusha/DDD-Printable-Wall-Control-System

I like the Gridfinity system a lot, but I was frustrated with the end quality of using the DDD wall control brackets along with this adapter, so I made them into a single part. My version also prints with no supports or assembly required.

Print with the "Top" side down and use an arachne based perimeter generator because there's some thin walls on the first layer. I would also recommend printing the first layer slowly (10mm/s) to ensure bed adhesion, as there isn't much surface area.

Low Friction Spool Holder Adapter

Low Friction Spool Holder Adapter

Are you like me and upgraded your bowden tube, but held on to the old one?

Well you are in luck!  Use it as part of this adapter to reduce friction between your spool and the spool holder.

Designed primarily for the Ender 3, but any similar spool holder should work.

Yes this is a mashup, however it does have significant changes and qualifies as unique work.  See license.txt for more details.

1. Cut two bowden tubes to fit in side of each track.
2. Remove the tube from your spool holder and snap on the adapter.
3. Put the tube back on the spool holder.
4. Enjoy

- Easy snap fit!
- Bowden tubes are low friction by design.
- The curved shape further reduces friction by limiting contact with the spool to two points.
- The curved shape uses gravity to keep the spool centered on the spool holder.

Supports are required. I would suggest using support blocker on the bowden tube holes, they seem to print fine.  

* I used tree supports and a brim.
* I printed at 5° hotter than normal to help with layer adhesion.
* I printed at 0.12 for a smoother look. However during testing I printed at 0.2 and it worked without issue.


IKEA Kura kids tent mount adapter

Ikea Kura kids tent adapter for beds with flat barriers.
Central hole d25mm can be used for additional reinforcement by plastic water pipe.


Mount.stl

55mm Filter adapter for iphone 11-13

Iphone11.stl

92-120mm offset adapter.stl

120-92mm.stl

Dual 120mm mounted fans to 4 inch female air duct hose adapter

dual120mmto4inch.stl

Pool-Helper

Pool_Helper.stl

Sidewinder X2 Mosquito-LGX Adapter.stl

An easy drop in ABL probe relocation bracket made by TheInappropriateMaker on Thingiverse that is super simple to use. 
Unfortunately it was just a tad bit too short, and it caused a nozzle crash. This is unchanged, however the probe is moved down an extra 2.5mm. 

Original:
https://www.thingiverse.com/thing:5273524

Ryobi 6 Gallon Shop Vac to 5 inch One+ Random Orbit Sander Adapter

Narrow Schrader Valve Adapter

This adapter is a Schrader-to-Schrader connection designed to be able to connect to a valve in a tight corner. It is a friction fit by design, but for a better and easier seal, an 8mm OD O-ring can be pushed into the female end. The diameter of the female end is 12mm. I suggest printing it in PETG, or PC for strength.

Print Settings:
infill 100%
0.16mm layers
0.5mm line width
brim for adhesion
no supports needed
print at the highest practical temperature for the material used

Adapter

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Wii-Tar DIY Adapter Case

GT Omega Cockpit Sim Racing Rig Adapter For Beavis Racing Shifter and Handbrake

Simple hose adapter for shop vac.

Single 45 RPM Adapter

Bambu X1C Vent Adapter

View 25 new models

Power Wheels Battery Adapter

Power Wheels Back Wheel adapter

Starter Adapter

18650 BATTERY ADAPTER FOR XML-T6 TACTICAL FLASHLIGHT

2x7 WallControl to 1x4 Gridfinity Adapter

Low Friction Spool Holder Adapter

IKEA Kura kids tent mount adapter

55mm Filter adapter for iphone 11-13

92-120mm offset adapter.stl

Dual 120mm mounted fans to 4 inch female air duct hose adapter

Pool-Helper

Sidewinder X2 Mosquito-LGX Adapter.stl

View 16 new models

Narrow Schrader Valve Adapter