**A planter for your home or garden that elevates your favorite plant.**
It has holes for water drainage and keeps your plant saver then on the ground or serves as additional space in a larger pot.

**Versions included**
- V2_multi_details: three faces and fine details
- V2_multi_basic: three faces and smooth surfaces
- V2_single_basic: one face and smooth surfaces
- V1: The older version one

**Scaling / size**
- Upscaling (100% +): as big as you want
- Regular size (100%): 115 x 115 x 200 mm
- Downscaling (99% – 61%): works great
- Minimum size (60%):  69 x 69 x 120 mm
Everything smaller than that may cause issues

**Print settings**
Material usage (100% scale): 120g
Print time: (100% scale): 10h

Material usage (60% scale): 35g
Print time: (60% scale): 4,5h

Material: PLA
Print direction: stl is rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: A brim is recommended but not necessary 

Watertight printing: If you have a well set up machine it comes automatically - Otherwise here are some tips: Increase your wall count (at least 3), level your bed nicely, decrease print speed, increase layer height (at least 0.2mm), increase print temperature, check your seam quality, calibrate your e-steps and fine tune your retraction settings to make sure no holes appear after a layer change.

Planter “Extra”

Planter_V2_multi_details.stl

**A castle inspired planter with water drainage via the moat.**

**Scaling / size**
- Upscaling (100% +): as big as you want
- Regular size (100%): 153 x 157 x 102 mm with a inner size of ca 96x96x90mm and a wall thickness/small feature diameter of 2mm minimum
- Downscaling (99% – 61%): works great
Minimum size (60%):  62 x 65 x 61 mm with a inner size of ca 58x58x54mm and a wall thickness/small feature diameter of 1.2mm minimum
- Everything smaller than that is not tested but maybe possible :D

**Print settings**
Material usage (100% scale): 200g
Print time: 16h (100% scale): 16h

Material usage (60% scale): 50g
Print time: 16h (60% scale): 5h

Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: none

Watertight printing - If you have a well set up machine it comes automatically - Otherwise here are some tips: Increase your wall count (at least 3), level your bed nicely, decrease print speed, increase layer height (at least 0.2mm), check your seam quality, callibrate your e-steps and fine tune your retraction settings to make sure no holes appear after a layer change.


Planter castle

**A castle inspired planter with water drainage via the moat.**

**Scaling / size**
- Upscaling (100% +): as big as you want
- Regular size (100%): 153 x 157 x 102 mm with a inner size of ca 96x96x90mm and a wall thickness/small feature diameter of 2mm minimum
- Downscaling (99% – 61%): works great
Minimum size (60%):  62 x 65 x 61 mm with a inner size of ca 58x58x54mm and a wall thickness/small feature diameter of 1.2mm minimum
- Everything smaller than that is not tested but maybe possible :D

Don't forget to post your makes!

**Print settings**
Material usage (100% scale): 200g
Print time: 16h (100% scale): 16h

Material usage (60% scale): 50g
Print time: 16h (60% scale): 5h

Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: none

Watertight printing - If you have a well set up machine it comes automatically - Otherwise here are some tips: Increase your wall count (at least 3), level your bed nicely, decrease print speed, increase layer height (at least 0.2mm), check your seam quality, callibrate your e-steps and fine tune your retraction settings to make sure no holes appear after a layer change.

If you experience any problems, please feel free to contact me on twitter or Instagram

Castleplanter.stl

**A unique Planter based on two species.**
Tree: Fagus Sylvatica
Mushrooms: Formitopsis Pinicula

**Versions included**
- Planter: The Planter
- Planter_no_drainge: The Planter without drainage.

When choosing your version take into consideration the aging process of the print. The drainage water will inevitably color the saucer part with dirt and lime as all planters do. For me this is a nice patina, but you may prefer the print to stay clean.

**Scaling / size**
You can scale the print as you with wish from 60% to 100%+

- Upscaling (100% +): as big as you want
- Big (100%): 205 x 182 x 137 mm with an inner size of ca 95 x 95 x 134 mm and a wall thickness of 4 mm
- Regular (80%): 164 x 146 x 110 mm with an inner size of ca 76 x 76 x 107 mm and a wall thickness of 3,2 mm
- Small (60%): 123 x 109 x 82 mm with an inner size of ca 57 x 57 x 80 mm and a wall thickness of 2.4 mm

**Print settings**
Material usage (100%): 300g
Print time (100%): 22h

Material usage (80%): 180g
Print time (80%): 14h

Material usage (60%): 90g
Print time (60%): 7h

Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: none

Watertight printing: If you have a well set up machine it comes automatically - Otherwise here are some tips: Increase your wall count (at least 3), level your bed nicely, decrease print speed, increase layer height (at least 0.2mm), increase print temperature, check your seam quality, calibrate your e-steps and fine tune your retraction settings to make sure no holes appear after a layer change.

Planter “Sylvatica Tree”

Planter.stl

**A Planter inspired by old video games where stuff would just glitch into a wall. **
The design can be either hung onto your wall or put down next to in.

**Versions / Files**
- Planter_with_saucer: The Planter with drainage via the small saucer
- Planter_without_saucer: Just the Planter
- Holder: The holder that works for both versions with a screw-hole diameter of 5.5mm

**Instructions**
- Choose your version and if you want to hang it or put it down.
- You can either screw or glue it onto your wall. There are various glue or tape products for wall fixation out there. Old fashioned screws and dowels are the most reliable fixation. I hung 5KG of Books onto the wall mounted print for over a week to test the strength. It can hold probably even more but the soil and plant will usually not exceed 2KG in weight.
- Insert the shelf by moving it horizontally onto the holder until the holder is completely inside the cutout. Then proceed to move the shelf down and the holder locks.
- Enjoy!

Size (Planter_with_saucer): 105 x 130 x 121 mm

**Print settings**
Required build volume: 140 x 140 x 130 mm
Material usage: 140 g
Print time: 10 h

Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: none

Watertight printing: If you have a well set up machine it comes automatically - Otherwise here are some tips: Increase your wall count (at least 3), level your bed nicely, decrease print speed, increase layer height (at least 0.2mm), increase print temperature, check your seam quality, calibrate your e-steps and fine tune your retraction settings to make sure no holes appear after a layer change.


Wall planter “Glitch”

Planter_with_saucer.stl

**A Planter inspired by old video games.** It is a low poly, slightly crooked design to commemorate how things looked like in the early days. While oddly shaped the planter is very functional and fast to print with a lifted drainage for happy little plants.

**Scaling / size**
- Upscaling (100% +): as big as you want
- Regular size (100%): 193 x 128 x 131 mm – has a wall thickness of 2 mm
- Smaller (80%): 154 x 102 x 105 mm – has a wall thickness of 1.6 mm
- Minimum size (60%):  116 x 77 x 79 mm – has a wall thickness of 1.2 mm

**Print settings**
Required build volume: 200 x 200 x 140 mm
Material usage: 230 g
Print time: 13 h

Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: none

Watertight printing: If you have a well set up machine it comes automatically - Otherwise here are some tips: Increase your wall count (at least 3), level your bed nicely, decrease print speed, increase layer height (at least 0.2mm), increase print temperature, check your seam quality, calibrate your e-steps and fine tune your retraction settings to make sure no holes appear after a layer change.

Planter “Double Glitch”

Glitch_double_planter.stl

This is a collaborative project between [Lofted Goods](https://thangs.com/designer/LoftedGoods) and me.

**A highly detailed planter based on a 3d scan of an ash tree (Fraxinus excelsior).** It comes with a hidden drip tray that perfectly locks into the surface texture.

The planter comes in two sizes with two versions each. One with the wall holder and one without for desktop usage. The tray and pot have a little indentation on the front to give you orientation help when inserting the pot into the planter.

**Wall mounting**
You can either screw or glue the planter onto your wall. The holder has compartments for command strips. The screw holes are 5 mm in diameter. For the US #10-12 x 1-1/4 in anchors and screws are the best option. If you choose to print the big wall mounted version and want to mount it with screws, make sure to print the screw insert, too.

**Print settings**
Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: none

Tree bark planter “Fraxinus Excelsior”

pot_small.stl

**A 3d scanned tree trunk planter with hidden drip tray.**

Tree: Carpinus Betulus
Mushrooms: Fomes Fomentarius
The Tree scale is 1:10 – but you can print it bigger!

Single and multi-color printing models are included as STL and 3MF! They work with all current and usual multi color setups.
You can either print the parts in one go or sperate and glue on the mushrooms. Check the images for positioning reference.


Size assembled: 144 x 162 x 160 mm

**Print settings**
Required build volume: 170 x 170 x 120 mm
Material usage: 250 g

Material: PLA
Print direction: files are rotated correctly
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Infill: 15%
Build plate adhesion type: none

Tree trunk planter “Carpinus Betulus”

Split.3mf

Split_Mushroom_1.stl

Split_Mushroom_2.stl

Split_Mushroom_3.stl

Split_Mushroom_4.stl

Split_Mushroom_5.stl

Split_Mushroom_6.stl

Split_Pot.stl

Split_Pot_markers.stl

Split_Tray.stl

Whole.3mf

Whole_Pot.stl

Whole_Tray.stl

These planters were designed after my recently released Fancy Easter Eggs.  I really like the texture patterns I used on the Eggs and wanted to continue exploring more ways to use them!  There are 3 Planters in this series; Diamond, Grid, and Web.  They are all the same size (excluding thickness) and print with no supports needed.  The planters have build in drainage holes, and I also designed and included a drip tray that works for each of the designs with raised ribs to facilitate water draining.

**Printing Info:**		
**These are just the settings I used to test the model, feel free to use whatever settings work best for you.
**FDM or Resin:** FDM or Resin.  Resin may not be good for plants though
**Model Size:** 102 mm x 102 mm x 70 mm
**Scaling:**	Scale up as you please.  You can probably scale down but do with caution because wall thickness will become an issue at a certain point. 
**Supports:** None
**Infill/Perimeters:** I just used 10% infill with 2 perimeters, but I would use extra perimeters for more strength.
**Nozzle Size:** 0.4
**Layer Height:** 0.2

**Printing & Assembly**					
- No special instructions, just print and you're good to go.  
- If you scale the planter, just scale the drip tray the same amount and they'll work fine together."						
						
								
**This design is uploaded with a non-commercial license. Downloading this file does not grant you the right to sell commercially.

If you would like to consider gaining access to ALL of the models and the rights to print and sell, you can check out my Patreon at https://www.patreon.com/thinair3D

Textured Planter Series

diamond_textured_planter.stl

[Instructions](https://prinnit.com/ForgeCore/design/368KCbjxwIIz7Vs1LtcCHEY89Ok?tab=instructions&highlight=instructions)
[Hardware](https://prinnit.com/ForgeCore/design/368KCbjxwIIz7Vs1LtcCHEY89Ok?section=hardware&highlight=hardware)
[Filaments](https://prinnit.com/ForgeCore/design/368KCbjxwIIz7Vs1LtcCHEY89Ok?section=filaments&highlight=filaments)

**Aloe Vera Pen Plant** - _Intermediate_ 

This Aloe vera Pen Plant makes the perfect addition to a desk. It keep your space lively and green but each stem also serves as a pen!

The stems magnetize onto the base, and each stem has a pen refill inside of it so you can write with them!

**How to Assemble**
[Assembly Video](https://www.youtube.com/watch?v=gKL_YTxY1dU)
Insert magnets into the base of the stems, and into the holes on the base.
Insert Pen refills into stems, make sure to align notch on pen.
Repeat for each stem.




Aloe Vera Pen Plant

1- Easy Print 3mf -Aloe Vera Pen Plant.3mf

Freebie Gecko .stl

Pot Insert.stl

Aloe Pot.stl

Aloe Base.stl

Stems (E) and (F).stl

Stems (C) and (D).stl

Stems (A) and (B).stl

[Instructions](https://prinnit.com/ForgeCore/design/3683r122rHEAMl6xlLBoN3sgjz3?tab=instructions&highlight=instructions)
[Hardware](https://prinnit.com/ForgeCore/design/3683r122rHEAMl6xlLBoN3sgjz3?section=hardware&highlight=hardware)
[Filaments](https://prinnit.com/ForgeCore/design/3683r122rHEAMl6xlLBoN3sgjz3?section=filaments&highlight=filaments)

**Spinny Plant Pot** - _Beginner_ 
This Plant pot is not only aesthetically pleasing, its also fun and functional. It is made from two parts that spin together, and has a build in drip tray to prevent root rot.

These pots were designed in collaboration with Hendrick's Design, who makes nice looking plant pots.

This design was inspired by those spinning containers, but made functional as a plant pot. If there's interest, I can make more styles of this planter as well, with different exterior patterns, or taller so it spins more. 

Spinny Plant Pot - Twist Together Pot with Built in Drip Tray

1 - Easy Print 3mf - Spinny Pot.3mf

Inner Pot.stl

Outer Pot.stl

[Instructions](https://prinnit.com/ForgeCore/design/3683b06e7EiDYr29TSHuXmkIhX9?tab=instructions&highlight=instructions)
[Hardware](https://prinnit.com/ForgeCore/design/3683b06e7EiDYr29TSHuXmkIhX9?section=hardware&highlight=hardware)
[Filaments](https://prinnit.com/ForgeCore/design/3683b06e7EiDYr29TSHuXmkIhX9?section=filaments&highlight=filaments)

**Pothos** - _Intermediate_
Another Articulating Plant! This one turned out really lifelike. Took me a couple dozen versions to get it right. I made it while surrounded by 3 real pothos plants to try and get it to look as realistic as possible. Put this in a hanging pot, and it will look awesome! Make sure to cover the base with dirt to get an even more realistic appearance.

Pothos - Articulating Plant

1 - Easy Print 3mf - Pothos.3mf

Dirt.stl

Leaf.stl

Long Branch.stl

Pot.stl

Short Branch.stl

Stem.stl

[**COMMERCIAL LICENSE**](https://than.gs/u/1467611?plans=true) // [**UNLOCK ALL FILES**](https://than.gs/u/1467611?plans=true)
[**DISCORD SERVER**](https://discord.gg/cxwMkmyP3u) // HELP REQUESTS
[**FILAMENTS USED**](https://www.amazon.com/shop/terradeverdant?ref_=cm_sw_r_cp_ud_aipsfshop_SAKKYVPYPZDF9QR2QY31) // AMAZON EQUIPMENT
**======================**

**PRINT SETTINGS**
If you want to just use it as an orchid pot no need to print the liner.
8-15% infill, 20% for sturdy heavy.
5 top layers, 7 if 8% infill.
2-3 outer walls.
No supports.
Raft or brim if you have adhesion issues.

**SCALE SETTINGS**
This is the scale for the outer diameter and not the liner diameter.
PLANTER & TRAY
3" OPENING: SCALE 66.04%
3.5" OPENING: SCALE 77.04%
4" OPENING: SCALE 88.05%
4.5" OPENING: SCALE 99.06%
5" OPENING: SCALE 110.06%
6" OPENING: SCALE 132.08%
7" OPENING: SCALE 154.09%
8" OPENING: SCALE 176.1%

The Lyren Planter Pot & Orchid Pot Hybrid with Drainage Tray: Modern Home Decor for Plants

LYRENPLANTER.stl

[Instructions](https://prinnit.com/ForgeCore/design/3684PNO8mkSijmWJ7KxQtMcRLVA?tab=instructions&highlight=instructions)
[Hardware](https://prinnit.com/ForgeCore/design/3684PNO8mkSijmWJ7KxQtMcRLVA?section=hardware&highlight=hardware)
[Filaments](https://prinnit.com/ForgeCore/design/3684PNO8mkSijmWJ7KxQtMcRLVA?section=filaments&highlight=filaments)

**String of Pearls** - _Intermediate_

The String of Pearls Succulent is a popular houseplant because of its unique appearance. It is one of my favorite plants because of the way it dangles down. This model is designed this to articulate with ball and socket joints that snap together. It dangles nicely, and can be assembled to be as long as you like.

Put this in a hanging pot, and it will look awesome!

**Customizable:**

This is a very customizable print. You can print out as many segments as you want to make a very large or very small plant. There are Y branches so you can split segments into multiple branches, just like the real plant.

If you want, you can sell a smaller version by including fewer pieces, or large ones with more for a higher price. Or even sell them as kits, so customer can assemble them themselves!

The pot in these photos was a real pot that I had at home, I included an optional printable pot in the download that fits perfectly with the base, in case you don't have one the right size at home. 

String of Pearls Articulating Plant

1 - Easy Print 3mf - String of Pearls.3mf

Base.stl

Freebie - Flexy Caterpillar.stl

Segment chain.stl

Y Branch.stl

This holiday season has been absolutely insane, and I have not had a spare moment to print new designs, so I asked you all how you'd feel if I released models that I haven't actually printed yet, and the response was 100% positive. This will not be the new norm. I will continue printing and testing new models going forward, just need to get through the holiday craziness first!

That being said, not having to print and photograph models will allow me to get new models out to you all much faster and more often. This planter uses the same twist lock design as my others, it's just a different shape and design, so I'm fairly confident in the print settings even though I haven't had a chance to print it yet.

This design is just the smaller, 2.75" size (both wall mounted and tabletop) for now. I'll add a 4.5" size soon.

**Supports**
None needed!

**Scaling**
I wouldn't recommend scaling this one since it perfectly fits the command strips and the screw holes are designed specifically for #10-12 x 1-1/4 in anchors and screws.

**Orientation**
The planter and tray should have their bottoms on the build plate. All mounts should have the sliding dovetail facing up.

**Print Settings**
.2mm layer height
15% grid infill
2 walls

**Filament & Hardware**
Filament I used for this print: Overture Matte Light Brown PLA
Hardware: #10-12 x 1-1/4 in screws

Filament and hardware/non 3D printed items for this model can be found on my Amazon Storefront, linked here: https://linktr.ee/loftedgoods

MCM Planter

MCM Tabletop Pot 2.75.stl

MCM Tray 4.5.stl

MCM Wall Pot 4.5.stl

MCM Tabletop Pot 4.5.stl

MCM Planter.3mf

2.75 Command Screw Mount Round.stl

4.5 Command Screw Mount Round.stl

Screw Insert.stl

This is one of my new favorites! The quilted pattern prints really well and looks great in any color. Both the 2.75" and 4.5" are available to print now. I've been improving my workflows so I hope to always release both sizes at the same time from now on.

This planter works with the same mounts as all my other wall planters. I've also included tabletop versions that don't have the wall mount.

**Supports**
None needed!

**Scaling**
I wouldn't recommend scaling this one since it perfectly fits the command strips and the screw holes are designed specifically for #10-12 x 1-1/4 in anchors and screws.

**Orientation**
The planter and tray should have their bottoms on the build plate. All mounts should have the sliding dovetail facing up.

**Print Settings**
.2mm layer height
15% grid infill
2 walls

**Filament & Hardware**
Filament: Bambu Lab Latte Brown & Dark Blue Matte PLA
Command Medium Picture Hanging Strips
Hardware: #10-12 x 1-1/4 in screws

Filament and non 3D printed items for this model can be found on my Amazon Storefront, linked here: https://linktr.ee/loftedgoods

Quilted Planter

Quilted Pot 4.5.stl

Quilted.3mf

[Instructions](https://prinnit.com/ForgeCore/design/368OKOeKHepdTC2zE27IUmsF8Pr?tab=instructions&highlight=instructions)
[Hardware](https://prinnit.com/ForgeCore/design/368OKOeKHepdTC2zE27IUmsF8Pr?section=hardware&highlight=hardware)
[Filaments](https://prinnit.com/ForgeCore/design/368OKOeKHepdTC2zE27IUmsF8Pr?section=filaments&highlight=filaments)

**Monstera Coasters** - _Beginner_    **Albo Version** - _Intermediate_

The Monstera is a super popular plant with its rather unique style of leaves. I surrounded myself with several different Monstera plants while designing this to make it as realistic as I could.

This Coaster Plant is an excellent way to store coasters, and get some more foliage into your home. Small magnets hold the leaves onto the plant, and they come off easily when you need a coaster. Snapping the leaves back onto the plant is also very satisfying!

There are a few different stem types and leaf types so you can customize your plant how you would like. 

**ForgeCore Freebie**
Check the Easy Print 3mf File for a **Freebie Snail**! A fun little articulating print that pairs well with the Monstera. Or just print on its own!

Monstera Coasters - Classic

Easy Print File - Monstera Coaster Set 3mf.3mf

Albo Leaves.stl

Leaves.stl

Stems.stl

Freebie Snail.stl

Plants

Activity related to collaborating with others on models

Likes, comments, and activity from your community

New content from your premium memberships

Emails and messages from designers you follow

Get notified when someone purchases your models or memberships

desertmoonfarms