tracking pixel
Colby G

Aloe Vera Pen Plant

by
ForgeCore
Follow
Follow
Remix Model
ForgeCore
ForgeCore
Image 1 of 20
Aloe Vera Pen Plant 3d model
2D
3D
Makes
Aloe Vera Pen Plant 3d model
Aloe Vera Pen Plant 3d model
Aloe Vera Pen Plant 3d model
Aloe Vera Pen Plant 3d model
Aloe Vera Pen Plant 3d model
Aloe Vera Pen Plant 3d model
Aloe Vera Pen Plant 3d model
Aloe Vera Pen Plant 3d model
Aloe Vera Pen Plant - Came out great! - 3d model
Aloe Vera Pen Plant - It’s really cool but not functional. The pen holes are all either too big or too small. I have to drill some and add hot glue to some. The spines have sharp points which would make it very difficult to use as a pen. The lids don’t stay on at all. - 3d model
Aloe Vera Pen Plant - Finally got my print finished, it turned out great after I figured out the scaling issue.  - 3d model
Aloe Vera Pen Plant - Aloe Vera - 3d model
Aloe Vera Pen Plant - How do you get the pen in the leaf?  Also magnets don’t fit. I am using a Bambu printer. - 3d model
Aloe Vera Pen Plant - Printed with Hatchbox white pla and Eryone olive green pla. Opted to paint the spots on later tos ave filament. I didn’t have any red clay-like filament so I made my own white geometric planter that I scaled to fit the insert in blender. 
Tips: Hit the stem holes with a heat gun on low for maybe 10 secs each to make it easier to get the pens down in them. 
Bore out the caps with a small rasp/file or exactly knife for a better fit. I’ve still got a few to fine tune. 
Once you get magnets in the base, give each installed magnet a pair and mark the outward face with a sharpie so you don’t install it wrong into the stem. 
Use a flat surface on a pair of pliers to persuade the magnets into the holes easier. 
If you dial in your printer this all fits together very well! I printed mine across an A1, an A1 Mini and a K1 Max and everything is fairly snug and lines up well. Great design! Kudos Forge! Thanks for sharing. - 3d model
Aloe Vera Pen Plant 3d model
Aloe Vera Pen Plant 3d model
Aloe Vera Pen Plant 3d model
Aloe Vera Pen Plant 3d model
Aloe Vera Pen Plant 3d model
Aloe Vera Pen Plant 3d model
738 Likes1.9K DownloadsMarch 20, 2024


This Aloe vera Pen Plant makes the perfect addition to a desk. It keep your space lively and green but each stem also serves as a pen!

The stems magnetize onto the base, and each stem has a pen refill inside of it so you can write with them!

Components You'll need to order

  1. The Magnets: Small Round Magnets 5x3mm (Amazon) (same magnets as all other prints)

You'll need a total of 40 magnets. 2 per each stem, and 2 per each stem attachment. Don't worry, they aren't that expensive!

  1. The Pen Refills: 0.7mm x 107mm ballpoint pen refills (Amazon)

Filament Used: Green Plant Color: Ziro Matte Military Green (Amazon) Grey Dot Color: Polyterra Matte Muted Green (Amazon)

Assembly:

Each Plant requires

  • 1 Base
  • 2 of Stem A
  • 2 of Stem B
  • 2 of Stem C
  • 2 of Stem D
  • 1 of Stem F
  • 1 of Stem G

Insert magnets into the base of the stems, and into the holes on the base. Insert Pen refills into stems, make sure to align notch on pen. Repeat for each stem.


738 Likes1.9K DownloadsMarch 20, 2024




738 Likes1.9K DownloadsMarch 20, 2024