Victorinox SAK Bit Holder

SAK_Bitholder_6.stl

Braun series 5,6,7 shaver protective cap

Braun567capV2.stl

Victorinox Swiss Army Knife Pocket Clip

Victorinox_PocketClip_V1.stl

Pencil Pen Box

PenBoxBody.stl

ClothesHangerExtension / Space Saver

A simple but effective space saver for your wardrobe. Hang five garments in the space you earlier used for two.
"folds out" for easy access.

Print in any material you like, to ensure stability I recommend min 4 walls and 20% infill

Creality Spider Speedy hotend

Angled Top Spool Holder Mount 

A quick'n'dirty mounting bracket for the stock spool holder of Ender-3-type printers converted to direct drive. It angles the spool to 45° behind the top extrusion (and turns it 90° against the stock setup) in a perfect position for a centered filament supply. 

Lightsaber display stand

LightsaberStandArm.stl

CurvedKatanaLongHandle.stl

A remix for 3D Printing World's Curved Katana model (https://thangs.com/designer/3dprintingworld/3d-model/Collapsing%2520Katana%2520with%2520Curved%2520Blade-48843) - A Katana is supposed to be a two-handed sword and the original handle was way too short.

THIS is ONLY the revised handle, for all the other parts please refer to the original creator's page (and follow his printing advice to ensure a successful print).

Cold Shoe Mount

ColdShoeMount.stl

Basket insert for ultrasonic cleaner

UltrasonicInsertBasket.stl

CRTouchCover

One of these indispensable life hacks ... when printing with embedded magnets you will experience that for a few layers upon insertion every time the CR Touch passes the magnet the probe is getting sucked out onto the print. Depending on your print either the probe might get damaged or the print - or both. This cap prevents just that. 
Needless for a BL Touch since this probe is plastic. 

Ender 3 v2 minimalistic hotend cover + dual 4010 blower part cooler

MiniHotendCoverSpiderSpeedy.stl

FlushCutter replacement grips

FlushCutterGrips.stl

Thule WingBar Profile

A replacement for the Thule Wing Bar rubber profile which might come loose and lost when driving at higher speeds.

The model is just updated to slide in easier, the standard length is just about 10cm so you need some to fully cover your bars.

Prints nicely in TPU95A standing upright with no supports, I recommend you use LostInTech's fine TPU cura profile (https://www.lostintech.co.uk/profiles/) to slice this particular model

AirVentBracket for Toyota RAV4 (2019+)

If you own a Toyota RAV4 (5th model, 2019 onwards) and feel the need to mount anything to your dashboard, look no further:
Here's a simple no-tools-needed mounting clamp that slides nicely around the dash cushions just under the side air vents and is strong enough for your everyday phone, garage door remote, picture frame - whatever.
 
The clamp installs on the car, the mounting plate clicks on to the clamp - bingo!
If you feel it is too thin, scale it - sideways only, since otherwise it won't fit any more. You knew this, didn't you?

But ... wait ... just how do I ... ??? 
Easy: Since you're here you're into making things - good! Just design a custom case for whatever you want to mount,  marry this case with the mount plate (in any 3D software that handles .stl or .step files) and you're done.

Mounting: 
Mount from below, i.e. hook the 90° side of the clamp between cushion and dash body, then push on the upper part until it snaps between cushion and vent frame and you're done.

Printing: use PETG since in cars you might expect higher temperatures than what PLA could handle. Print the clamp lying on the side to ensure strength due to the layers nicely go along the clamp to carry the load and not to worry about layers becoming detached - they won't. As for "your" case / hook / whatnot - print in a direction that covers for the forces the case has to take up.

AirVentBracket-1.5mm.stl

EN-EL23Case.stl

Just a quick'n'dirty transport case for EN-EL23 batteries (used in some Nikon Coolpix models).

RAZPro_SaddleBracket.stl

A bracket to fasten the fantastic RAZPro bicycle tail light to your saddle. As is zip ties are intended for that purpose, but they can be  severed too fast, plus fastening the light with zip ties is a very shaky solution.  

Print as oriented, there are sacrificial layers designed into the screw holes. My bracket goes together with the original saddle mount, you need two 3x20 bolts plus nuts (press fit into the hex holes), the bolts fit through two holes in the original mount, providing a very secure fit. 

XT500_IgnitionLock_ContactCarrier

This is a contact carrier to replace a broken original one inside the ignition lock of an ancient Yamaha XT500 motorbike.
Yes, complete replacement locks are available at arount 30E, but - hey, we're makers, so we make 😄 

Ender3 v2 BT-Remote Switch for print timelapse video

Tripod mount Lanyard loop

Ender3v2 BMG direct drive adapter (Drivinator Remix)

BMG-DD-Adapter_Trigger.stl

Retro Rocket Piggy Bank

RetroRocketPiggybank_Rocket.stl

Buck Converter Case, yet another

BuckConverterCase_Case_M3x20_HexCylinder_Vents.stl

Honeycomb attachment for Doerr photo lights SVL 180 and 112

Here's a honeycom attachemnt fitting Doerr Photp photo/video lighhts SVL180 and 112 for anyone who hasn't got one or lost the one coming with his light.

Replacement Wheel for Samsonite Cabin Trolley

TrolleyWheel-78mm-v5.stl

Dyson Trigger Lock

DysonTriggerLock

Fuse carrier adapter for Toyoty RAV4 Hybrid (from 2019)

Coffee container extension for "Finessa" coffee machines (MioStar, Koenig, Turmix, etc., Tchibo Esperto Caffe)

coffe_bean_container.stl

Oil funnel for BMW R 850 / 1200 C

Bike rack extension for Tubus Fly Evo

Ender 3 v2 cable strain relief (w/ bowden support)

Dual Z symmetric Belt Tensioner (revised)

Ender 3 V2 Power Switch Mod - Remix

Double Hook

Activity related to collaborating with others on models

Likes, comments, and activity from your community

New content from your premium memberships

Emails and messages from designers you follow

Get notified when someone purchases your models or memberships

UliLac

Achievements

Novice Maker

Sequoia

Voyager

Fan Favorite