Two easily printable Chiseled Sandstone blocks! These are sized at 200mm³ to be easily scaled to your liking. 10% scale will make a “normal” 20x20x20 block much like a little calibration cube.

Recommend using Fuzzy Skin and tweak it to give the appearance of smoothed stone.

Minecraft Chiseled Sandstone

MC_ChiseledSandstone_Creeper.stl

A simple resizable pot with foot inserts to raise it. Feet should be printed in flexible filament, but a version is included for non-flexible as well.

Low Poly Zig Zag Planter

ZigZagPlanter.stl

Introducing the WyzeHouse! This fully 3D printable birdhouse will provide your feathered friends with a luxuriously safe nesting site that you can monitor remotely. 

This enormous suburban home is split into multiple parts, and will fill the entire bed of average-sized printers with the main house coming in at a whopping 201mm*165mm*120mm. 

The home features multiple drainage holes should rain find its way in, and ventilation in the roof to keep your avian friends cool during warmer weather. The camera housing has a detachable magnetic roof that will require ten (10) 6mm*2mm disc magnets. 



You will need:

Ten (10) 6x2mm disc magnets for cam roof

Four (4) M4x16 Screws for primary roof

Four (4) M3x12 Screws for cam house mounting

Four (4) M3x8 for skylight

Eight (8) M3 nuts for skylight and cam house mounting

(Optional) Four (4) M4 screws (read below)
Four (4) Eye hooks.

One (1) Wyze Cam V3 with modified focus ring. (see below for link)

Optional:

You may add a layer pause to insert nuts into the main housing for roof mounting, there is a cutout that will inset the nuts and print over top of them. 
Use silicone sealant around all edges to increase weather resistance.

Assembly:

Screw the WH_CamHouse to WH_MainHouse tightly, use silicone sealant if desired. This will allow you to easily tighten the nuts from inside.

Screw WH_Skylight to WH_MainRoof and tighten nuts.

Insert WH_LargeWindow and two (2) WH_SmallWindows into WH_MainHouse, seal if desired. IMPORTANT: You must insert the windows before attaching the roof.

Screw WH_MainRoof to WH_MainHouse and use sealant if desired.

Insert/glue/heatset magnets to WH_CamHouse, WH_MainRoof and WH_CamRoof, ensuring you have the correct polarity to attach them together. 

Screw eye hooks to WH_MainRoof at an angle to avoid layer splitting.

Insert Wyze Cam V3 upside down, running camera power through the large hole in the bottom. 

Under Advanced options in your Wyze app, make sure you enable “Flip image 180” so the camera feed isn't upside down.

Please note that the camera can be mounted right side up, but I found it easier to access the Setup and SD card slot.

Modifying the Camera:

Your Wyze Cam V3 needs to be modified in order to focus close enough so your image isn't blurry. Below are two that I would recommend, I also recommend using TPU for this but the filament is up to you.

[Focus Knob for Wyze Cam V3 - Printables by Innesport](https://www.printables.com/model/129397-focus-knob-for-wyze-cam-v3)

[Wyze Cam V3 Lens Adjuster and Cover by WCTT](https://www.printables.com/model/277736)

[How to install/modify the lens by FusedLine on YouTube](https://www.youtube.com/watch?v=kkKAMMNlaf4)

Final Thoughts:

This is a long print, it will take over 40 hours even at larger layer heights. 
I recommend using Clear PETG for the windows, and following [Rygar1432's guide on How to Print Glass](https://www.printables.com/model/15310-how-to-print-glass) for best results.
Everything should fit together, even if it is a bit snug in some spots. You may want a drill for attaching the main roof.



Let me know what you think, and be sure to share your prints and feedback with me so I can continue to improve this project. 

WyzeHouse - Wyze Cam V3 Birdhouse

WyzeHouse.stl

Introducing the Post-It Pallet Rack. Finally you have a place to store all the amazing Post-It Pallets you've no doubt been printing out. These (probably) OSHA-approved are rated to support a maximum of six fully loaded pallets, but if it ends up holding more I won't tell!

Shelves are designed to be customizable and support multiple height configurations. Additionally, each rack structure bar can be bolted to another to easily attach and expand more storage bays. Each storage bay can accommodate a 76mm*152mm space. 

 

Each shelf requires eight (8x) M3x8 screws to secure it to the structure bars.

Post-It Pallet Storage Rack

TDPR_Structure.stl

Are your post-it notes just too heavy? You want to lift them with your forklift but there's simply no way with them sitting on the ground! Load them up on to this perfectly post-it note-sized pallet.

Supports not recommended, hope your bridging is well tuned, but you do you!

Re-sizeable to fit any post-it note!

Post-It Pallet

Giant. Lightning. Plug.

Continuing my tradition of printing #BigTech, I give you the Apple Lightning charging plug. This is meant to be printed very large, to act as a scale model or display. It is not designed with functionality in mind, though someone far more clever than I could probably make it work for something.

I've included a pre-sized up version of the stl, bringing the model to roughly 700%, while other parts are scaled slightly smaller/slimmer so they should fit together decently.

 

Glue is required to get the pins to stay in place, unless you just have really incredible tolerance skills.

 

Printing instructions:

Infill: 20% - 40%

Layer Height: 0.2mm or smaller

No supports for anything

 

The metal housing at the top contains some very fragile bridges, I recommend printing this in either PLA+ or something more durable like PETG.

 

This is a modified version of the model originally uploaded by Mark over on GrabCAD. Parts have been split and adjusted slightly for a better print.

Apple Lightning Connector

This is basically an inverted standard calibration cube, and prints in about the same amount of time. But this one is hollow to test retraction, overhang angles, and an insanely difficult bridge at the top.

The cube measures 20x20x20mm and has 2mm thick walls. 

I recommend using 2 perimeters to maintain the gaps in the Z at the top. 

 

Please be aware that the .obj file includes a small loaf of bread, which is not present in the stl file. Thank you for understanding.

Zare Calibration Cube

Zare_CaliCube.stl

For your favorite rock and roll legend, a tiny Marshall Amp with space inside! Held together with eight 8x2mm magnets. This should be perfectly sized to hold a few gift cards, guitar picks, or anything else that you might consider reasonably small.

Assembly Instructions:

Print the top and bottom in their default orientation, flipping may result in issues.
The logo should be printed in vase mode for quality and reduced stringing
Plate may be very tight, and require glue to remain seated. 
Magnets may or may not require glue depending on your printer's tolerance ability
**Magnetic version uses 8x2mm disc magnets.**
Happy printing, rock on!

Marshall Amp Box

MarshallAmpBox_MMU_Split (1).stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Taptic Digital