Drawer Organizer

Drawer organizer v3 Full.stl

Simple Heart Box with Lid Remix "I Love Us"

DISPLAY ONLY Remix of Heart Box with Initials Lid ILU.stl

Simple Heart Box with Lid Remix "I Love You"

DISPLAY ONLY Remix of Heart Box with Initials ILY.stl

Initials Simple Heart Box with Lid Remix "You+Me"

DISPLAY ONLY Remix of Heart Box with Initials YouMe.stl

Initials Simple Heart Box with Lid Remix "K+R"

DISPLAY ONLY Remix of Heart Box with Initials KR.stl

Initials Simple Heart Box with Lid Remix "H+S"

DISPLAY ONLY Remix of Heart Box with Initials HS.stl

Initials Simple Heart Box with Lid Remix "J+M"

DISPLAY ONLY Remix of Heart Box with Initials JM.stl

Initials Simple Heart Box with Lid Remix "J+S"

DISPLAY ONLY Heart Box Remix.stl

Honeycomb Hex Bin "B"

These are a set of bins I designed specifically for a built-in in my apartment. This one measures 8 inches wide by 5 inches deep by 9 inches (ish) tall (sorry for the units my EU friends).

I've found PETG performs best with this particular model. PLA works, however I usually had a lot of cleanup on the stringing in the hexes afterwards, whereas PETG @ 230c and 150 mm/s worked nearly flawlessly without any stringing.  Please comment your successful settings though as I am still having trouble getting the floor of the bin to print without blistering when using Concentric patterns or the like.

Designed in Tinkercad, the hex pattern is a repeating pattern trimmed on the edges, so re-sizing to whatever dimensions you need should be pretty simple, but message me if you need a particular set of dimensions and I might take a crack at it if I have time. Tinkercad file below to remix with if you want:
https://www.tinkercad.com/things/hZ36bubRkEJ?sharecode=ZK1efOMKQ0vd52pIDA50fgz2jkDBfDEKqysG56LNbEQ

Honeycomb Hex Bin "A"

These are a set of bins I designed specifically for a built-in in my apartment. This one measures 4 inches wide by 5 inches deep by 9 inches (sorry for the units my EU friends). 

After 8 iterations, redesigns and reprints, I've found PETG performs best with this particular model. PLA works, however I usually had a lot of cleanup on the stringing in the hexes afterwards, whereas PETG @ 230c and 150 mm/s worked nearly flawlessly without any stringing.  Please comment your successful settings though as I am still having trouble getting the floor of the bin to print without blistering when using Concentric patterns or the like. 

Designed in Tinkercad, the hex pattern is a repeating pattern trimmed on the edges, so re-sizing to whatever dimensions you need should be pretty simple, but message me if you need a particular set of dimensions and I might take a crack at it if I have time. Tinkercad file below to remix with if you want:
https://www.tinkercad.com/things/hZ36bubRkEJ?sharecode=ZK1efOMKQ0vd52pIDA50fgz2jkDBfDEKqysG56LNbEQ



 Hexagon Candle Holder Remix

Loved the design of JannickSchulz' H Candle Holder, but I wanted to use it for a large candle instead of a votive. Remixed for a near filling candle, I am using in a decorative use case though, some candle might have a flat too close to the edges to be safe/not melt/warp the PLA, so I'd recommend a higher temp-resistant material in those cases.

Sticky Note Container

A simple desk container for 3 sticky notes in 2 sizes (designed for Post-it standard 1/2"x2" and 3"x3" sizes). I recommend printing with concentric top/bottom layers for a nicer finish. 

I add felt pads to the bottom to avoid any surface damage of a desk, but not necessarily needed. 

Lego Headband

A composite remix of ivan's "Headband" from Printables and Maker 0824's "Lego Brick" from Thingiverse. It provides Lego-compatible mounting points for small builds or minifigs. 

Original Headband model:
https://www.printables.com/model/344924

Original Lego model:
https://www.thingiverse.com/thing:4532105

Lego Headband.stl

A dabbler in VR, game design, 3d modeling, screenwriting, filmmaking, photography.

Sweetzer

Achievements

Seedling

Debutant

Voyager

Amateur Maker