tracking pixel
Ruven B

Gear Ball

by
RuvenBals
Follow
Follow
Remix Model
RuvenBals
RuvenBals
Image 1 of 86
Gear Ball 3d model
2D
3D
Makes
instagram-play
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball - this came out so cool ty for sharing  - 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball - Mushroom Pose - 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball - made from white PLA. Found out the hard way that this material was way too prittle for the clamps, so I redid them in nylon (PA) - nice :) - 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball - increased size of connector length, get a tight fit. - 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball - Too cool. Pictures don’t do it justice  - 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball - Printed on my Bambu X1C in Gratkit tri color red/green/blue - 3d model
Gear Ball - This is an amazing model!  - 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball - See the pin I printed in TPU. This ball is 65% I had issues with the pla pins breaking at this size. The tpu seems ok. It's a hard tpu. - 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball - NEW PIN DESIGN FOR SMALLER SCALE - 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball - scaled to 80% and initially added a little X-Y hole compensation, the connectors were too loose so reprinted those separately at 80% with no compensation and she's holding together well, albeit still a bit too lose but a lovely flower-Dilophosaurus-sea-creature to play with! - 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball - I love this print ! Thank you  - 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball - Thanks for this,  Prints amazing on Ender v3 KE Using the standard 0.2mm profile in Orca slicer 2.1.1

No rafts needed, I was worried about the heart so at layer 100, I slowed the print down to 75%

Printed the pins with 100% infill and its clipped together no problems at all. Using Tri-colour PLA+ Silk from Sunlu.

Absolutely love it thanks - 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball - I like it very much. - 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
Gear Ball 3d model
This model is restricted by licensing terms. 
1.1K Likes4.9K DownloadsMay 31, 2024
This model is restricted by licensing terms. 


You need: 4 Big Gears 4 Small Gears 8 Connectors 1 Heart

Print settings: no supports needed. Just print with a standard profile. I used a brim for better bed adhesion.

Assembly: Watch this Video: https://youtu.be/vWKSQDT7o_A

Push the connectors into the heart and then put the gears on top. This one is a little tricky since the gears are variable sizes. You need to connect the ball just like in the picture when its a ball. Make sure you assemble the big gears fist and that they form half a ball. And then put in the small gears. Use the Pictures as a guidance.

Leave a like if you can :D


1.1K Likes4.9K DownloadsMay 31, 2024




This model is restricted by licensing terms. 
1.1K Likes4.9K DownloadsMay 31, 2024
This model is restricted by licensing terms.