Welcome to the Blu-ray edition of our Display Collection at Holoprops.

After the free Switch launch, we are expanding the system to one of the most versatile formats out there: Blu-ray cases.

This frame is designed to turn your physical games and movies into clean, elegant wall displays you can swap instantly depending on what you are playing, watching, or collecting.

What fits inside this frame

This Blu-ray Frame is compatible with:

• PlayStation 5 game cases
• PlayStation 4 game cases
• PlayStation 3 game cases
• Xbox Series X game cases
• Xbox One game cases
• Standard Blu-ray movies
• Standard Blu-ray steelbooks

If it uses the classic Blu-ray case format, it fits.

A timeless frame, designed for any setup

Just like the Switch version, this is a clean rectangular frame with a neutral design that blends naturally into any gaming or movie setup.

3 variations are included so you can choose the look that fits your wall best.

One Wall Mount. One System. Infinite Possibilities.

This is very important: The Blu-ray Frames use the exact same Wall Mount as the Switch Frames.

That means:

• You do NOT need a new mounting system
• One Wall Mount works across the entire Display Collection
• You can mix Switch Frames and Blu-ray Frames on the same wall seamlessly

If you already printed the Switch Wall Mount, you are fully compatible. (If you are new to the collection, the Wall Mount and the Wall Guide are included for free here as well.)

You can also check out the Switch Frames here and build a mixed display wall.

Magnetic Wall System - Simple, Clean, Future-Proof

The Wall Mount is fully standardized across the entire Display Collection.

Wall installation:

• Uses 2 screws
• Drywall requires anchors
• Wood studs can use wood screws

A drilling template is included so everything stays perfectly aligned and level.

Inside the Wall Mount, you will glue 2 standard round magnets: 10 mm x 3 mm.

⚠️ Very important - polarity rules

• Both magnets inside the Wall Mount must be glued with the same polarity
• Every Wall Mount must follow the same direction
• The rear magnets of every frame must match that polarity

This rule applies to EVERYTHING:

• Switch Frames
• Blu-ray Frames
• Badges
• All future accessories This is what allows instant swapping anywhere on your wall without thinking.

Magnets Inside the Frame + Badge System

Each Blu-ray Frame includes:

• 2 rear magnets for wall mounting
• 1 extra corner magnet for future badges and decorative accessories Always install both rear magnets with matching polarity across all frames.

Magnets are glued with:

• A small drop of super glue
• Press firmly into place
• Let fully cure before mounting We personally use a super glue accelerator so the bond sets in seconds.

⚠️ Polarity matters. If installed incorrectly, frames and badges will not attach properly.

One-Second Removal Removing a frame takes literally one second: Grab from the bottom Gently pull toward you The frame detaches naturally from the magnets, no force needed.

Optimized Printing and Premium Finish

All Blu-ray Frame variants are printed at a 35-degree angle for the cleanest surface finish possible. The included 3MF file is fully pre-configured with: Optimized supports Strategic orientation Clean visible surfaces Easy support removal Strong but material-efficient settings We spent days testing and fine-tuning everything in Bambu Studio. Please use the provided 3MF files for best results.

Each frame prints in about 3 to 4 hours, depending on the variant.

For best results, we recommend: A clean build plate, washed with warm water and mild dish soap, air-dried A printer in good condition (plate and nozzle not too worn) Using the 3MF file exactly as provided

Perfect Fit for Games, Movies, and Steelbooks

The internal geometry is carefully engineered so that:

• All supported cases slide in easily
• No pressure on the artwork
• No scratches or damage Everything sits snug, clean, and perfectly aligned.

Printing Details

• Nozzle: 0.4 mm
• Layer Height: 0.2 mm
• Infill: Hatch (8%) or Cubic (15%)
• Supports: Yes. Perfectly calibrated in the 3MF file
• Walls: 2

3MF Files Ready to Print Out-of-the-Box

We fine-tuned countless slicer settings: infill, speed, bridges, seams, and more. Hours of research and testing go into every file so you get a true plug-and-play experience. The included 3MF files are optimized for Bambu Studio and should work correctly with Orca Slicer and Prusa Slicer. Using other slicers may break alignment, supports, colors, or custom settings.

Join the conversation

We’d love to see your prints! Share them on our Holoprops Discord and connect with the community.

Licensing All Holoprops models are 100% original creations, hand-sculpted with care and creativity. These models are our own intellectual property and are protected accordingly.

Personal use only. For commercial rights, join our Merchant Tier: Thangs Merchant Tier

Filaments used

All filament from the Bambu Lab Store. Mostly from the PLA Metal lineup.