Swivel your desktop speaker to any angle you wish, lock it into position, and ROCK OUT!

Maximum speaker weight: 8.3 lb (3.8 kg)

Print Settings:
4 walls (minimum) for .6mm nozzle
6 walls (minimum) for a .4mm nozzle
15-20% gyroid infill

Basic Assembly Instructions:
1. With the upper plate flat side down, drop left and right levers over center of castellated tabs on pivot points. Note the mirror images attached. Also, the opening on one side of the lever is slightly larger than the other. This is a taper to allow for easy fit over the tabs. Insert through the large opening :)
2. Flip over upper plate and 2-lever assembly. With the levers in the open position and the base flat-side down on a hard surface (the floor or sturdy table), straddle the ball of the base pedestal with the opening of the upper plate socket. Give the upper plate a nice hard smack downward so that the ball pops into the socket.
3. Rotate the levers a few times to smoothen the cam-to-flat contacting surfaces. It should quite a bit of resistance to rotate them into the close position. You can add a little grease/lube between the cams of the levers and the flat contacting surface. DO NOT add lubrication to the swiveling ball joint! You want this joint as dry as possible. Wipe it with some IPA before install if you handle it too much.
4. Place the stand in the desire listening position. Then place the speaker on top of the upper plate. With levers in the open or half-open position now. Adjust the orientation of the speaker, rotate the levers forward to lock it into place.

General Notes:
We recommend using PETG. But PLA, ABS, and ASA are perfectly fine too. Keep in mind that the surfaces making contact between the pedestal ball and the upper plate socket are subject to wear. After all, it's just plastic. The levers are there to add a little extra clamp force and increase the static friction force. Try to make all adjustments with the levers open. You can adjust the orientation of the speaker with the levers in the closed position. But, do so sparingly as this will reduce the holding power of your swivel joint in the future.

Pro-Tip: Get some foam rubber pads with adhesive on one side to stick to the bottom of the base!

Thanks!

Swiveling Desktop Speaker Stand by Deposition Sound

Desktop_Speaker_Stand_Pedestal_20240819.3mf

This is a 3D printable cabinet for an 8" powered subwoofer by Deposition Sound LLC. If you have a medium/small living space that is in desperate need of thick, juicy, and fast bass, these are just for you! They have been carefully tuned to 33Hz, with in-room extension down to the mid 20's Hz!

It is printed in 4 main quadrants, requiring roughly 1 kg of filament each. Assembly instructions coming soon! Check out https://www.depositionsound.com/ for updates and feel free to contact us with questions. Kit can be purchased here: https://www.depositionsound.com/shop

Woofer = Dayton Audio DCS205-4
Plate Amp = Dayton Audio SPA100-D
x12 M5 brass threaded inserts
x12 M5 x 16mm button head hex socket bolts
x12 M3 brass threaded inserts
x12 M3 x 12mm button head hex socket bolts
Lots of CA glue (assembly order matters), thicker the better!

Be sure to trim and strip the connectors on the plate amp wires. That way the 8" woofer spring connectors can receive the bare wire. Stuff 2oz of Poly-Fil into each quadrant and you're ready to rock. If using a slow curing adhesive, allow for ample cure time as this little 8" woofer will generate high pressure loads!

Note: We include flat-bottom feet that receive foam rubber pads for hard flooring. If you're placing these subs on a thick shag carpet, we recommend the spikes.

FDMS8 Powered Subwoofer by Deposition Sound

FDMS8_Powered_Subwoofer_20240731.3mf

This is our 3rd speaker design to date. We went way off-script with this loudspeaker, hoping to attract those with smaller build volumes and a desire for deep bass and excellent off-axis response. They pack the party animal of the FDM5's and sophistication of an FDMGeo all into a small footprint that's perfect as a desktop monitor. Don't be fooled by their size. They sound best at moderate volume levels and pack a punch that will catch you off guard! (more details coming)

For more information and kit purchase, check out https://www.depositionsound.com/

FDM4 Loudspeakers by Deposition Sound

FDM4_Loudspeaker_Main_Cabinet.3mf

The "Geos" are edgy, literally 😎

We've combined the sugary sweetness of the FDM5 top-end with an accurate and punchy mid-section and bottom end. If you're into critical listening, or even mixing and mastering, the FDMGeos are for you!

The FDMGeos will party all night long and wake you up in the morning with a fine cup of Espresso.

https://www.depositionsound.com/fdmgeo
https://www.depositionsound.com/fdmgeo-assembly-instructions

FDMGeo Loudspeakers by Deposition Sound

FDM_Geo_Rounded_20240310-EnclosureCabinet.stl

Check 3MF for cabinet mirroring!

Developed in the summer of 2023, these 3D printed bookshelf speakers are our first attempt at properly meshing 3D printing and audio.

We believe that we hit the mark!

FDM5 Loudspeakers throw out an impressively wide soundstage and boast a warm mid-bass response. The speakers are good clean fun, but they also know how to get down and dirty. Carefully tuned to reduce listening fatigue, you'll want to enjoy these speakers over and over with their sugary sweet top end and rich lows.

https://www.depositionsound.com/fdm5

https://www.depositionsound.com/fdm5-assembly-instructions

FDM5 Loudspeakers by Deposition Sound 

FDM5_Loudspeakers_20230804-EnclosureFront_Baffle.stl

Left-FDM5_Loudspeakers_20231102-EnclosureMain_Cabinet.stl

Right-FDM5_Loudspeakers_20231102-EnclosureMain_Cabinet.stl

**COMMERCIAL RIGHTS FOR ALL 3D PRINTABLE DEPOSITION SOUND PROJECTS**

Grants permission to sell physical copies of any [3D printable Loudspeakers designed by Deposition Sound](https://thangs.com/designer/DepositionSound). 

**(Selling digital files is expressly prohibited.)**

Commercial License to sell physical products created from these project files. (Refer to commercial licensing terms for further details.)

Commercial Production

FDM5_Loudspeakers_20230804-EnclosureCrossover_Stand-Off.stl

FDM5_Loudspeakers_20230804-EnclosureBinding_Post_Plate.stl

FDM5_Loudspeakers_20230804-EnclosureBeauty_Ring.stl

FDM_Geo_Rounded_20240310-EnclosureCrossover_Stand-Off.stl

FDM_Geo_Rounded_20240310-EnclosureFront_Baffle.stl

FDM_Geo_Rounded_20240310-EnclosureWoofer_Beauty_Ring.stl

FDM4_Loudspeaker_20240412-Front_Baffle_Final.stl

FDM4_Loudspeaker_20240412-Main_Cabinet_Final.stl

FDM4_Loudspeaker_20240412-Wave_Guide_O-Ring_Groove_Final.stl

FDM4_Loudspeaker_20240412-Woofer_Beauty_Ring_Final.stl

FDM4_Loudspeaker_Front_Baffle.3mf

FDMS8_Powered_Subwoofer_Foot.3mf

FDMS8_Powered_Subwoofer_Lower_Left_Quad.3mf

FDMS8_Powered_Subwoofer_Lower_Right_Quad.3mf

FDMS8_Powered_Subwoofer_Spike.3mf

FDMS8_Powered_Subwoofer_Upper_Left_Quad.3mf

FDMS8_Powered_Subwoofer_Upper_Right_Quad.3mf

**Our Mission**
To provide the absolute best sound experience at a budget price point using additive manufacturing for cabinet construction.

**Speakers Available**
[FDM5 Loudspeakers ➞](https://www.depositionsound.com/fdm5)

[FDMGeo Loudspeakers ➞](https://www.depositionsound.com/fdmgeo)

[FDM4 Loudspeakers ➞](https://www.depositionsound.com/fdm4)

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

DepositionSound

Achievements

Seedling

Debutant

Pinned models

FDM5 Loudspeakers by Deposition Sound

FDMGeo Loudspeakers by Deposition Sound

FDM4 Loudspeakers by Deposition Sound

FDMS8 Powered Subwoofer by Deposition Sound

Swiveling Desktop Speaker Stand by Deposition Sound

FDMS8 Powered Subwoofer by Deposition Sound

FDM4 Loudspeakers by Deposition Sound

FDMGeo Loudspeakers by Deposition Sound

FDM5 Loudspeakers by Deposition Sound