Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1548406.

I remixed samlego2 case for a slightly slimmer profile.
You will need 7 x 5mm countersunk M3 screws.

Your printer has to be well tuned, as tolerances are very tight
 I suppose scaling could be used if the case turns out too tight for you.

_Small improvements:_ the buttons only fit in the right order and will maintain their orientation.

The backplate is a blank meant to be customized.

This thing was made with Tinkercad. Edit it [here](https://www.tinkercad.com/things/1RoQ9iU7Fc8)

iPhone 5 iPhone SE Case

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1514145.

My take on Misan's drawing machine. I made one with a grbl controller and a CNC shield and adapted Misan's parts to be 3D printed.

Please read Misan's instructions as well.

The drawing machine is a small three axis robot that controls a pen or any drawing implement over a canvas. It is a complete open source design and aims to teach the basics of robotics.

Budget for one is about 80$. You will need a 3D printer.

The Z stage does not use a servo, as in Misan's machine, but rather one of those cheap 28BYJ stepper motors you can find for 1.50$ on eBay.

NOTE: The photos are of the current prototype, some of the modifications to the various bits and pieces have not yet been tested.

If you have a question, first search in the Comments section. If you can't find an answer, then ask in a Comment. I will answer as fast and as much as I can.

And please, share your makes!

Drawing Machine

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4817583.

This is a case for the most excellent KIM-1 recreation, the PAL-1 kit from Liu Ganning that you will find [here on Tindie](https://www.tindie.com/products/tkoak/pal-1-a-mos-6502-powered-computer-kit/).

If you like this and want to incentivize me to make more, consider a [donation](https://www.paypal.com/donate?business=PVG8U59GCJBCC&item_name=Help+me+create+new+stuff%21¤cy_code=CAD).

PAL-1 Enclosure

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1443598.

UPDATE 20161005: I have since upgraded to this: http://www.thingiverse.com/thing:1635585

I was not happy with [the official Wanhao clip](http://wanhaousa.com/pages/attaching-the-filament-stand-to-the-top-of-the-printer) that keeps getting looser and looser as you use it, and I did not want to drill holes in the gantry, so I designed my own.

It is a very tight fit, it has to be. I iterated the design a few times to make it work exactly right with my printer, which is a 1st gen Wanhao i3 Duplicator, but you may have to modify it to fit yours. The model is on Tinkercad. Edit it [here](https://www.tinkercad.com/things/332S0wRft66)

Wanhao i3 Duplicator Spool Holder Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1271779.

Print "cat_box.stl".

Meanwhile, measure the inside of a shelf compartment, remove about 10mm on each measure: width, depth and height.

With wire (e.g. recycled wire hangers), cut 4 x height, 2 x width and 2 x depth.

Using cardboard (or any other similar material cats like to sleep on), make a bottom plate (width x depth). 

Once the print is done, you should have 8 corners: 4 bottom clips and 4 top connectors.

Push the wire in the clips and the connectors as depicted in the other stl (not to be printed, it is just a model of how everything fits together).

Cover with an old t-shirt. Secure with safety pins or paper clips.
Let him enjoy...

(No cat was harmed in the making of this box. Fingers, however, were. Cats are extremely territorial...)

Ikea Kallax Insert for Cats

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1394500.

The usual octopi installation. The raspi is discreetly affixed to the left side of the frame, cables hanging down, power comes from behind. The camera protrudes a bit over the printer head and captures your fabulous prints.

It fits a Raspberry Pi 2 or 3. Can't say for the other models.

Raspberry Pi 2/3 Case with Camera Mount for Wanhao i3 Duplicator

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1428769.

A solder dispensing pen. Wrap some solder around a pencil, drop the coil of solder in the tube, thread it through the cap, and solder away! If your shirts have a front pocket, that's where the clip comes handy.

This thing was made with Tinkercad. Edit it [here](https://www.tinkercad.com/things/3U76JkveBAG)

Solder Pen

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4862134.

This is a makeshift HP-163 connector I made to power an old HP 5245L counter I bought from a retired electronic tech.

These connectors are nowhere to be found these days unless you want to pay through the nose for a "vintage" cable on eBay.

Fore more info on the PH-163, see [here](http://madrona.ca/e/powerConn/index.html).

If you like this and want to incentivize me to make more, consider a [donation](https://www.paypal.com/donate?business=PVG8U59GCJBCC&item_name=Help+me+create+new+stuff%21¤cy_code=CAD).

###WARNING! RISK OF DEATH!
_Mains voltage is dangerous. I am not an electrical engineer and cannot guarantee the safety of my design. Make it at your own risks._
**If you have a doubt, do NOT build this.**

###CAUTION!
_Old electrical devices should not be left unattended, even when they seem powered off (for example, the HP counter is still keeping its crystal oven on even when it is apparently "shut off"). One of the components could fail suddenly and cause a fire (a few diodes went up in flames while I was testing my unit). Also electrical standards have evolved and these devices are very probably less safe than modern equipment._

PH-163 Connector (HP Oval) 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1635585.

Yet another spool holder using 608Z bearings. It consists of two pieces that can be moved independently to adapt to the spool, and can support spools of any diameter down to 150 mm.

If you like this and want to incentivize me to make more, consider a [donation](https://www.paypal.com/donate?business=PVG8U59GCJBCC&item_name=Help+me+create+new+stuff%21¤cy_code=CAD).

Wanhao i3 Duplicator Spool Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1398824.

I reused the blade and the screw of a cheap dollar store pencil sharpener. 

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/0pWmQgfqb18

Pencil Sharpener

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1443081.

Specifically for [this desk](http://www.ikea.com/ca/en/catalog/products/80260701/).

You will need to remove the plastic with a utility knife to make a slot. Mind your fingers!

Edit it on [Tinkercad](https://www.tinkercad.com/things/43ijdJijFhp).

Ikea PS 2014 Clip-on Pencil Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1411567.

This is to replace the excellent (but fragile) acrylic laser cut case that came with the kit. (The cat did it...)

I love [this clock](https://www.adafruit.com/products/194), too bad Limor doesn't sell it anymore.

There are two models, a simple one [(here)](https://www.tinkercad.com/things/6XCHlypAwxY) without a back, and a more complex one, v2, with a back that holds with two 2mm screws [(here)](https://tinkercad.com/things/1KD2RJw3V4y). This one has even more of the honeycomb structure.

Please upload a picture of your prints!

Adafruit Ice Tube Clock Case

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1468669.

The original button broke. Replacement cost is prohibitive (30$ on Amazon!!!).

Frigidaire 131965300 Dryer Knob

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1339767.

_[Check out my new and improved version.](http://www.thingiverse.com/thing:1627424)_

The original grill would break the fan posts if tightened too much.

You can edit the model online on [Tinkercad](https://tinkercad.com/things/4ipP5q4aBZw).

####WARNING:
_Depending on your version of the Duplicator, the stock screws (M3 x 40) might end up being too short and you might have to change them for longer screws. I believe it depends on where they source the fan. Everything fits just fine on my first generation Duplicator with the stock fan and the stock screws.
If it does not work for you, feel free to take measurements, experiment with the [model on Tinkercad](https://tinkercad.com/things/4ipP5q4aBZw), and leave a comment here.
Thank you!_

Wanhao i3 Duplicator Extruder Fan Grill

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1627424.

You know those two little bits of tubing that keep falling and roll under the printer *every time* you unscrew the extruder open? 

*Gone.*

To help with the holes on the fan grill, there is a small plastic stop in each hole that helps with bridging. Once printed, pop them out with a 3mm screw, pushing from the inside.

This thing was made with Tinkercad. Edit it [online](https://www.tinkercad.com/things/4fhFwtfff3g)

Wanhao i3 Duplicator Extruder Fan Grill v2

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2586049.

I redesigned ywabiko's enclosure with wider tolerances. The Raspi assembly should be easier to slide in.
While I was at it, I used my favourite vent pattern and moved it from the sides to the front and back to shorten printing time.

If you like this and want to incentivize me to make more, consider a [donation](https://www.paypal.com/donate?business=PVG8U59GCJBCC&item_name=Help+me+create+new+stuff%21¤cy_code=CAD).

Raspberry Pi Zero W with pHAT DAC Enclosure

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1445480.

Yet another Wanhao i3 Duplicator Filament Guide for a top mounted spool using either the [Wanhao clip](http://wanhaousa.com/pages/attaching-the-filament-stand-to-the-top-of-the-printer) or [the one I designed](http://www.thingiverse.com/thing:1443598).

The lock is optional, but works well.

This thing was made with Tinkercad. Edit it [here](https://www.tinkercad.com/things/b9IunWUpUOO).

Wanhao i3 Duplicator Filament Guide

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1654801.

A new version of the filament guide that fits between my roll holder. Making the most of this clip shape...

Enjoy!

If you like this and want to incentivize me to make more, consider a [donation](https://www.paypal.com/donate?business=PVG8U59GCJBCC&item_name=Help+me+create+new+stuff%21¤cy_code=CAD).

Wanhao i3 Duplicator Filament Guide v2

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1796651.

The desk was a tad too low to go with our office chair, and had my favourite resident student hunching over books.

Print two sets of those to raise the working area by about two inches (47.5 mm exactly)

This thing was made with Tinkercad. Edit it [here](https://www.tinkercad.com/things/dTyCoBOiZbl).

Ikea PS 2014 Feet Extenders

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

CYUL