This Skull Jewelry Set includes a necklace, choker, bracelet, and different sizes of rings and earrings!

See here for video: https://youtu.be/VNuI0LSqct0

The pieces that contain multiple skulls use a unique print-in-place ball-and-socket joint that allows the finished print to fully turn, twist, and rotate. See below for details and printing instructions

Necklace: The Skull Necklace is provided in two versions: a closed-loop 36-skull version and an open-loop 35 skull version. Both prints have an outside print diameter of 177mm and a finished length or circumference of approximately 50cm. The closed-loop version is too small to fit over most heads but can be used as a prop. The ends of open-loop version are connected using string or elastic. Multiple necklaces and chokers can be combined to make some serious skull bling. 

Choker: The 19-skull Choker print has an outer diameter of 111mm and finished length of approximately 28cm.  The ends are connected using string, ribbon or elastic. Multiple necklaces and chokers can be combined to make some serious skull bling. 

Bracelet: the 20-skull Bracelet print has an outer diameter of 111mm and finished circumference of approximately 28cm.  

Rings: The rings are provided in sizes 5, 7, 9, 11 and 13 to fit all fingers and thumbs. There are plenty of online sizing guides if you are not sure what size you need. 

Earrings: Skull Earrings are provided in single and multiple-skull dangling versions. You will need some standard earring hooks and ¼” jump rings to attach to the embedded loop on the top skull.

Here are some additional printing instructions related to the print-in-place ball-and-socket joints:

The inner spheres print on top of tiny supports within the cavity of the neighbouring skull. Once printed, a light twist of each skull frees the ball within the cavity and the skull chain can turn and bend. Be sure to let your print fully cool first! If the plastic is still soft, the connector may break when you try to move it.

Plan your supports carefully. A suggested technique using Cura is to raise the object of the build plate by 3mm, and then add tree supports underneath. Switch “Support distance priority” to “xy overrides z” and tighten up the “xy support distance” to 0.1mm.

This design is a submission to the "HalloWearables Design Contest With Zack Freedman"

#HalloWearable #HalloWearables #skull #bones #skeleton #jewelry #necklace #bracelet #ring #rings #earrings #halloween #cosplay


Skull Jewelry Set

Jewelry Set.stl

A Choker style necklace to match my flexi fidget bracelets. Prints in two parts and clips together

I'd advise printing the first layer nice and slow. I printed at 0.3mm layer height with the frist layer at 10mm/s

Flexi Fidget Choker Necklace

Choker Front.stl

Re Created lighter and Printable Pirate Earrings. Print just 1 half or 2 ea. and glue them together back to back and paint to desired color/finish..

Pirate Earing Model.step

Simple string heart earrings.

Print at 0.3mm layer height (if using Prusaslicer turn off 'wipe while retracting' in the printer settings)

Shown on my earring display stand which you can find here: https://social.thangs.com/m/630222

String Heart Earrings

Earring DISPLAY ONLY.stl

Printed in Place, a long beautiful Pumpkin Necklace! Easy print! Scaled for a bambu but could be printed on many printers. 

0.2 layers, slow on the joints. 

This is the updated version with better joints. 

HALLOWEENWEARABLE
#HALLOWEENWEARABLE
#HALLOWEEN
#WEARABLE
#HALLOWEENWEARABLES
#WEARABLES

SPOOKY PUMPKIN NECKLACE - HALLOWEENWEARABLE, PRINT IN PLACE - DRAGON, JACK O LANTERN, SCARY, PIP

The model that hilariously became an icon. It is lovingly referred to as 'sharp' cheddar. 
I designed this within 12 hours for Cheezy Chain for @CheezyChainz (go find him on tiktok and instagram!) as a thank you for ordering from my website to support me. He is a wonderful creator and person.

I ended up really liking the design when it was finished, and I am now finding reasons to wear a cheese necklace! They fall similar to chunky Mardi Gras beads and are so much fun.

I am keeping this free because it is a fun and silly little design that I whipped together in an evening, but I do ask that you go follow CheezyChainz and send him some love if you download this design.

PLEASE READ:
This model (like all Pretzel Prints designs) is under copyright, and upon purchase, you do not have the right to sell prints commercially. The digital files are NEVER to be re-sold, shared, or given away!

If you are interested in selling this model commercially check out my Patreon! https://www.patreon.com/user?u=25054604

Thank you for your support and honesty!

Cheezy Chainz for Cheezy Chainz

This is a mini Coffin Box perfect for mini Halloween sweets or to put small gifts suck as earrings inside!

Print in vase mode and they fit together perfectly.

 

Vasemode coffin Box

box.stl

This model is created for printing with resin earrings. 

Antioloid Inspired Earring

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4382611.

### A skyrim logo necklace! 

Original model by: https://www.thingiverse.com/thing:3042456

I basically adapted it to a simple necklace, thicker, added proper support, an attachment point etc...

### Printing!

I included my supported stl's as well as the sliced files for the anycubic photon S.

### My print settings: (in use in the pre-sliced file)

Printer: Anycubic photon S

What to print?: 4 double sided skyrim necklaces at once

Time to print?: around 8 hours

Layer height: 0.02 mm

Quantity of resin used: around 20 mL

Type of resin: Anycubic Eco plant-based resin (macaroon pink and blue)

Printing temp: around 20C, the highest I could get at the time

###Washing, Curing

I recommend removing the supports before curing. It's a bit more tedious with gloves and a mask, but they come off easier and there is less risk of damage.

also recommending to cure underwater, just tried with the last batch and they came out great.

###Sanding

I started with 100 grit, then 150, 250, 600 grit.

Basically sand the supports marks until they are flat, then increase the grit to have a smooth finish.

###Painting

I did two thin layers of black primer, then two layers of shiny chrome, short 

### /!\ WARNING /!\

I left the first three ones I printed on my desk in the sun before painting and they started to warp after 2-3 days. so maybe avoid leaving them in the sun before painting. (or cure them more).

### Have fun :)

Skyrim logo necklace

A simple earring display stand.
Prints in two parts and slots together

Earring Display Stand

Earring Stand DISPLAY ONLY.stl

Majora's Mask with hoop for necklace or ornament. 

Majora's Mask 

This is a necklace display model designed to be printed in vase-mode for a quick and easy print.

Download the necklace in the picture here: https://social.thangs.com/m/391329

Necklace Display - quick print

Butterfly earrings.
Print 2 of the same model for both Ears.

Butterfly Earring.stl

luffy's straw hat that can be used as a keychain keychain, or a necklace if you want.
find the original model [here ](https://thangs.com/mythangs/file/67158?activeBottomTab=history&activeViewer=single&wwNewVersion=true)

no support needed 

this model is licensed under_[ theCreative Commons - Attribution - Non-Commercial - Share Alikelicense.](https://creativecommons.org/licenses/by-nc-sa/4.0/)_


straw hat keychain 

luffy's straw hat that can be used as a keychain keychain, or a necklace if you want.
no support needed 

We designed these earrings a few years ago. Looking at them, a couple of details come to mind that would work wonderfully, but nonetheless, it's a very, very simple design that is worth sharing. Furthermore, you can create various combinations with them, mixing Jack and Zero or having sets with either Jack or Zero.

We designed them to use them with a costume at Carnival. They print very quickly and in two colors that everyone has, white and black.

******************************************

All Quimicafeina designs are protected by Copyright Law. By downloading, you have no right to sell or share any digital files or reproductions from those files.

To get access to all of our designs or for a commercial license to sell the physical prints of the files, you can support us on patreon. Link in the bio.

Jack and Zero earrings

zero_earring.stl

A small charm with an added loupe for mounting to an earring hook.  Best printed using resin in batches.  There is usually a little spoilage in removal when you print this small.  Use 1 or maybe 2 sprues per piece.

Disclaimer:  Please refer to the manufacturer of your resin for associated health risks. Please take proper steps to cure your prints properly and follow all directions for making resin prints wearable safely. Machenna56k claims no responsibility for the safe handling of printed items created from these files.

Milk Jug Earrings

MilkJugLoupe.stl

A small charm with flat back for mounting on an earring stud.  A challenging build that requires steady hands for gluing cleanly.  Best printed using resin in batches.  There is usually a little spoilage in removal when you print this small.  Use 1 or maybe 2 sprues per piece.

Cassette Stud Earring

CassetteFront.stl

Hi friends, I also created this accessory for the contest. 
They are bat-shaped earrings, they are easily printed and you can use them to give an extra touch of style to your Halloween costumes.
 I really hope you like it.

HalloweenWearable
#HalloweenWearable

BAT-EARRINGS- HalloweenWearable

This simple, yet elegant, jewelry stand has your organization needs covered! The top arm can hold necklaces, bracelets, and rings. The top tray is perfect for holding your earrings and rings. The bottom tray can hold watches, rings, bracelets, and whatever else you may want to place in it!

The print is broken into 5 parts so that you can print it in different colors and without supports! The posts thread together and the arm pressure fits into the hole at the top.

**Print Settings**
I printed the bottom tray at 50% infill to make sure the thread post is ridged. The top tray can be printed with 20% infill.

The posts should be printed at 50% infill to keep it ridged. For the posts a wide brim and slower speeds should be used so that nothing gets nocked over while printing.

Hope you enjoy this print!

FashionJewelry

Categories

Popular

Personalize

Trending