Whale Shark Fidget

BOBwhaleShark.stl

Cup of Teeth - Teacup

Dual Colour Teeth Cup - Teeth.stl

Gridfinity 1x1 Glasses Holder - No Supports

Here is a basic, 1x1 Gridfinity glasses holder. Holds sunglasses as well as eyeglasses up to 145mm in width. However the file can easily be modified to increase or decrease height as needed.

Use the following print settings and you should have no issues as well as an under 2 hour print:

Layer height: .24 - .32
Walls / Top / Bottom: 3
Infill: 10% - 20%
Supports: none

View all of my Gridfinity models here:

https://thangs.com/search/gridfinity%2520%252B%2520%2522thingymaker9000%2522?manualModelView=true&scope=all

Customizable Alphabet Train

Full Alphabet.stl

Print-N-Place Klackers

These are klackers or noisemakers that print in place as one part! They make a great toy for kids but I also find them as a great fidget toy for adults too.  

This a new version which is much easier to print. To have a successful print, most importantly you must have good adhesion to the bed. For the loudest klackers, more walls and infill the better but watch out for curling. If you have issue with curling, enable z-hop, or increase the amount of plastic after the tangency of the balls.

Getting them to Klack
If you are having a hard time getting them to klack I found the easiest way to get them started is to set them flat on a table so the klackers are spread out and as you pick them up off the table whip them back down to make them klack. There are two techniques; the single klack and the double klack as demonstrated here: 


Floppy Disk Coasters - 2 Designs

floppy-front.stl

Inferno Articulated Dragon

Inferno Articulated Dragon.stl

Bus Stop - With Free Cyberpunk - Sci-Fi Gift Ideas for RPG and Wargamers

bus_stop_cover.stl

Ghostie Mouse Soap Holder

Ghostie soap holder 2.stl

Reindeer Gnome 2024

ReindeerGnomeSTL_FunFam3D.stl

Feraligatr Skull - Solid & Hollow - Pokemon

Feraligatr Skull-Hollow.stl

MP Bolt-Locked Insert - Flex-On Rail Slider

Bolt-Locked Insert - Flex-On Rail Slider.stl

Thompson 1928 Sub-Machine Gun - Functional Assembly

MAGAZINE 50 TOP.STL

CPX-2 Prop Gun v2.1 (+Prop Mag, Silencer +Custom Grips)

lowPolyCPX2_Gv2.stl

Cthulhu Head (Pre-Supported)

Cthulu_Head.stl

Skull Pop Beads

These “Skull Pop Beads” snap together to form spooky chains or rings as long as you want!

See here for video: https://youtu.be/pCv3Yx5U_7k 

The pieces are designed to be printed in “Vase” or “Spiralized” mode. The file is optimized for printing with a 0.4mm nozzle. Printing with different nozzle sizes is still possible but will affect the tightness of fit.

Each piece uses approximately 0.4g of material, making this a great design to use up the scraps of filament you have lying around! A full 1kg roll could print approximately 2500 beads, enough to make a chain 50m (164ft) long!

To connect pieces together, simply pinch the top end of one piece so that the opening becomes oval-shaped. Insert the oval end of the second piece inside and release. The pieces remain connected but can be separated again if needed. Create long chains or rings by adding as many pieces as you want.

Each piece takes approximately 5 minutes to print. It is, however, much more efficient to print multiple pieces sequentially! Setting up spiralized models to print “one at a time” takes a bit of planning as the pieces must be spaced and sequenced properly so that the hot end or gantry does not collide with the finished prints as it moves on to the next print. 

Make the bottom open by setting “bottom layers” to zero. Good build plate adhesion is essential, so ensure that your machine is well calibrated.

Similar Designs: 
Pop Bead Garland: https://social.thangs.com/m/513337 


t

Most Downloaded of All Time

Categories

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Whale Shark Fidget

Cup of Teeth - Teacup

Gridfinity 1x1 Glasses Holder - No Supports

Customizable Alphabet Train

Print-N-Place Klackers

Floppy Disk Coasters - 2 Designs

Inferno Articulated Dragon

Bus Stop - With Free Cyberpunk - Sci-Fi Gift Ideas for RPG and Wargamers

Ghostie Mouse Soap Holder

Reindeer Gnome 2024

Feraligatr Skull - Solid & Hollow - Pokemon

MP Bolt-Locked Insert - Flex-On Rail Slider

Thompson 1928 Sub-Machine Gun - Functional Assembly

CPX-2 Prop Gun v2.1 (+Prop Mag, Silencer +Custom Grips)

Cthulhu Head (Pre-Supported)

Skull Pop Beads

Tiny Owl (inc 3mf)

kirby pen holder 3mf

Mushroom shelf “Amanita Caesarea”

Liquid Cat Fidget Toy Print in Place