Winter Goose Figurine – Cozy Christmas Goose with Sweater and Scarf

Cool duck in scarf_black.stl

XL Bauble

Threaded top.stl

Lucky Charm Candle Holder - 3D print STL and 3MF file

Lucky Charm Candle.stl

Spiral Tree Topper

Small trees need love, too! this topper is just under 200mm tall and weighs under 25 grams. I was able to print it in just 4.5 hours.

It requires no infill and no supports.

I designed it so I could print it in one piece on my printer (Anycubic Mega S). After adding a raft, it comes in at just 4.6mm shorter than the theoretical maximum of my printer. 

This is based on my Spiral topper, but it's been recreated from scratch with no boolean operations. I wanted to create a cleaner mesh. 20 hours later, I had a design ready to test. It printed beautifully the first time.

**Print Settings**
* Layer Thickness: 0.15mm
* Walls: 0.4mm (1 line)
* Top/Bottom: 0.45mm (3 layers)
* Infill: None
* Supports: None
* Raft: Yes
* Print Speed: 60mm/sec
* Outer Wall Speed: 30mm/sec
* Travel Speed: 80mm/sec

I used a raft with an 8mm margin (default in Cura is 5mm) to get good adhesion. Without a raft, the base makes very little contact with the buildplate. The raft worked perfectly. The ornament was locked in place without any wobble for the entire print, but when I went to take it off, it required no effort to remove the raft from the buildplate or from the ornament.

In theory, you can probably print it in vase mode, but when I sliced it that way in Cura, it didn't slice right. So, I printed it normally.

Small Spiral Topper.stl

Pumpkin Flexi -Smiley

PumpkinSitFlexi_Smiley4Color3MF_FunFam3D.3mf

Lattice Christmas Bulb 2024

Bulb Lattice.stl

Christmas Baby Shark - Mini Monster #3

MiniMonster3SantaHatSharkPrintStart3D.stl

Diamond Christmas Stretch Ornament 2024

Stretch Swoop Ornament 7 Whole.stl

Zigzag Teardrop Christmas Ornament

Zigzag Teardrop Whole.stl

Elf Door 

elf door frame.stl

Ruffled Fabric Egg 

License: Attribution-NonCommercial-NoDerivs
CC BY-NC-ND
***
***Sculpt by @ChelsC423***
Sized to fit a typical tea light candle. But can be printed larger or smaller for just décor!
***
***If you would like to sell physical objects, please see the CCT Partner tier on our Patreon***
***
If you would like to support me AND receive exclusive to Patron models every month check me out here:
https://www.patreon.com/chelscct


Ruffled Fabric Egg Decor.stl

Flowery Whatsit Ornament Suncatcher

*What is it?*
This is part of a series of designs that were originally intended as Christmas tree ornaments and I later found also made great suncatchers for any time of year (when printed with transparent filament/resin). This is the second in the series to be published.

Beyond that, what is it? Well, it's kind of a snowflake pattern (5 points instead of 6), kind of a star, kind of flowery, and bears a large resemblance to gothic architecture. Mostly, it's just a cool geometric design that I enjoy looking at.

*How to Hang it*
I've included two small, well hidden loops behind one of the arms so you can tie coat thread on them and hang it up. See the detail photo included above. They are really small and very well hidden.

**Print Settings**
You shouldn't need a raft or brim. 

*Print Time*
Depending on the wall thickness, these printed in 2-3 hours for me.

*Thickness*
If you want to use these as Christmas ornaments, I recommend trying to print this with 1 line (0.4mm) walls. As a suncatcher, it looks good with 1 or 2 line walls (I prefer 2). I needed to make the walls with 2 lines (0.8mm) to get a good print from the TTYT3D Silky Orange. I set the top/bottom thickness to 0.3mm.

You probably have your printer set up to print 1.2mm walls and top/bottom thickness. Don't use those settings for this design unless you plan to use it as a paperweight. If you forget to change them, cancel the print and start over.

*Flow*
I increased the flow to 110% for the outer walls and 105% for the inner.

*Infill*
This doesn't need any infill. Seriously. Don't add it unless you want to use this as a paperweight.

*Speed*
I print the first layer at 18mm/second. That makes sure that the complicated design gets good bed adhesion without a raft or brim. It also adds less time to the print and less clean-up than using a raft or a brim. If you have a cold bed, you might need the raft or brim anyway.

For all other layers, I use:
* 30mm/second outer wall speed
* 40mm/second inner wall speed
* 60mm/second overall speed

festive

Most Downloaded of All Time

Categories

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Winter Goose Figurine – Cozy Christmas Goose with Sweater and Scarf

XL Bauble

Lucky Charm Candle Holder - 3D print STL and 3MF file

Spiral Tree Topper

Pumpkin Flexi -Smiley

Lattice Christmas Bulb 2024

Christmas Baby Shark - Mini Monster #3

Diamond Christmas Stretch Ornament 2024

Zigzag Teardrop Christmas Ornament

Elf Door

Ruffled Fabric Egg

Flowery Whatsit Ornament Suncatcher

Gingerbread Cookie Ornaments Set 4

Gingerbread Cookie Ornaments Set 3

Swoop 3 Christmas Stretch Ornament 2024

Bunny Chick Clicker

Light Panels for Festive Lampost

Santa Bones

Rosebud Gnome

Lantern Christmas Stretch Ornament 2024