 Holiday Hangers: Santa, Snowman & Reindeer Trio

santatree.stl

Witch Frog Figurine — Halloween Fantasy Sculpture

Frog magician_тело_зелёный.3mf

Halloween Skeleton Turtle - A Spooky and Fun Toy

BODY.stl

Spiral Christmas Balls

#Summary
These are a quick, fun, and are very lightweight. Each ball has the same cross-section and twist. The main differences are the size and number of arms.

* Large ball: 80mm diameter, weighs less than 17g, takes about 6 hours to print
* Small ball: 56mm diameter, weighs less than 9g, takes about 3 hours to print

These are part of my [Christmas Collection](https://www.thingiverse.com/dazus/collections/christmas-collection).

I designed these using Affinity Designer (for cross-sections) and Blender (everything else).

The arms need support at multiple points to keep from warping and breaking if you're using an FDM printer. To make this quick and easy, I provided a version of each ornament with built-in supports. I still had Cura add supports, but only where the balls touch the build plate. For details, se the print settings below.

#Print Settings
##Basics

* Layer Thickness: 0.15mm
* Walls: 0.4mm (1 line)
* Top/Bottom thickness: 0.45mm (3 layers)
* Build Plate Adhesion: Brim

If you have holes in your print (from the thin walls), I recommend increasing flow and/or print temperature. You might also decrease print speed and travel speed (I use 30mm/second and 80mm/second).

##Infill

Infill is optional. They should print OK without it, but I added some just at the bottom of each ball. I used Cura's Support Blocker and Per Model Setting's "Modify Settings for Overlaps" to add 20% infill (Lines pattern) for the first 51mm for the large ball and 37mm for the small ball.

##Supports

I recommend using the versions of the balls with built-in supports. You'll still need a little support for the first few layers (where the ball touches the build plate), but my supports make printing the arms of the ball easy. You can remove my supports with your bare hands (no tools) and they leave little or no marks on the print.

I recommend printing these with Cura-generated supports "touching buildplate" with a 60-65 degree overhang angle and a brim for the supports.

For support infill, use Concentric pattern, 10% density. Roof density of 75%, floor density of 50% works well and releases cleanly.

The small ball doesn't need any supports for the inside roof. I found it printed very cleanly. 

The large ball printed well enough for my taste without supports for the roof. It print was a little rough, but it only shows if you pick the ornament up and look up from the bottom of the ornament. When it's hanging on a tree, you'll never see that part of it. There's enough space between the arms of the ornament that you could get tools in to cut up and remove supports if you want to add them, but I don't think it's worth the effort.

FREE-ster Eggs Multi-Pack

Bases - Free-ster Eggs.3mf

Starburst Christmas Ornament

**ABOUT THE DESIGN**
This is a new variation on my Christmas Balls with Integrated Stems and diamond patterns.

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**RESIZING**
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

**PRINT TIME**
About 4.5 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height. I decreased the print temp from my usual 200 to 190 for this, decreased the flow from 115 to 105, and increased the outer wall speed from 20 to 30 mm/sec. That was enough to go from stem that was molten goo to one that printed perfectly.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 – 0.8 mm.

I had the best results using Cura setting the default width to 0.4 mm with an alternate extra wall. 

*Infill*
This does not need any infill. JUST DON'T DO IT.

*Speed*
* Outer Wall: 30 mm/sec
* Inner Wall: 30 mm/sec
* Top/Bottom Speed: 30 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I relied on the supports for build plate adhesion. 

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. 

* Support Structure: Normal
* Support Placement: Touching Buildplate
* Support Overhang Angle: 49 Degrees

I added a support blocker 75 mm x 75 mm x 110 mm set 15 mm above the build plate so that the supports would only be added to the bottom of the ornament.

Diamond Lattice Christmas Ball

Egg Tealight Cover -*Breezy*

License: Attribution-NonCommercial-NoDerivs
CC BY-NC-ND
***
***Sculpt by @ChelsC423***
Sized to fit a typical LED tealight candle. But can be printed larger or smaller for just décor!
***
***If you would like to sell physical objects, please see the CCT Partner tier on our Patreon***
***
If you would like to support me AND receive exclusive to Patron models every month check me out here:
https://www.patreon.com/chelscct


Festive Lamppost

Christmas lamp post.3mf

Jolly Frosty Vase for Festive Decor

Jolly Frosty.3mf

Snow Dome Vase - Perfect for Winter Decor and Holiday Centerpieces

Snow Dome Vase.stl

Egg Tealight Cover -Bunnies

Christmas Spiral Teardrop 2023 

Christmas Spiral Teardrop Ornament 2023.stl

Aussie Snowman 

Aussie Snowman_SparkyFace5.3mf

Snowflake Christmas Tree Ornament – Holiday Festive Decor

New Year's ball_ornament.stl

Open Spiral Christmas Bell

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**CHALLENGING PRINT**
If you just got your first 3D printer and are looking for your first thing to print, this isn't it. Using the settings I recommend below, an experienced maker should be able to get a good print without many failed attempts.

**COMMON PRINTING PROBLEMS**
Assuming you use the print settings I recommended below, here are some common problems and possible fixes:
* Mushy print: Reduce print temp.
* Comes off bed: Increase raft size. Reduce print speed.
* Print looks rough: Reduce print speed.
* Breaks during printing: Reduce print speed and print temperature. If you can, increase cooling. Add more supports.

**PRINT TIME**
With my settings, it took about 3.5 hours.

**PRINT SETTINGS**
*Thickness*

* Layer thickness: .15mm
* Wall thickness: 0.8mm. If you want to go thinner to reduce weight, consider using Cura's “alternate extra wall” option so it alternates between 0.4 and 0.8mm walls with each layer. That may prevent gaps in the print.
* Top/bottom thickness: 0.3mm

*Infill*
This doesn't need any infill. Seriously. 

*Speed*
You'll want to use slow printer settings to that the print is accurate and to reduce chance the bell is pulled off the plate curing printing.

* Overall: 60mm/s
* Outer wall: 30mm/s
* Inner wall: 40mm/s
* Travel Speed: 65mm/sec

*Build Plate Adhesion*
The first layer of the bell is just a thin circle. I've found that a raft works well to provide bed adhesion. It also separates more cleanly than a brim for this model. 

*Supports*
This print absolutely requires supports to keep the spiral arms from breaking. By setting the overhang angle to 45 degrees, you get support exactly where you need it: at the base where the arms touch the rim and then curve, and at the roof of the bell. It's a lot lower angle than you might normally use, but it's needed for this design.

* Support placement: Touching buildplate
* Support overhang angle: 45 degrees
* Support pattern: Gyroid
* Support wall line count: 1
* Support density: 10%

Spiral Teardrop Christmas Ornament

Spiral Teardrop.stl

Diamond Christmas Ball

After creating a bell with this pattern (see Diamond Christmas Bell, I wanted to see what it would look like as a ball. I loved it, so I had to share it with you. It printed easily for me with just a little support. It looks great with multi-color PLA, but it'll also look great in solid colored PLA (opaque or transparent).

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

***PRINT SETTINGS***
* Walls: 0.4 - 0.8 mm (I made the walls of the ball 2 lines thick and the walls of the stem 1 line thick).
* Layer Thickness: 0.15 mm recommended. Anything from 0.1 - 0.2 mm should look good.
* Infill: None. Seriously. It doesn't need it. It just adds weight and print time.
* Rafts/Brim: I didn't use either. 
* Supports: I added normal supports with an overhang angle of 56 degrees. It holds the ball to the printing plate and supports the extreme overhangs at the base without adding a lot of time to the print.

Star Christmas Tree Ornament

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**WHAT IS IT?**
This is a fun Christmas tree ornament that would also make a fun suncatcher if it's printed with transparent filament. It's reminiscent of a cross, a star (it actually has 8 points), classical western architecture, and more. Using my settings, it's a nice weight at 100% and extremely light at 75% and smaller.

**EASY PRINT**
If you use my settings, you shouldn't have any problems getting this to print. If you print this with your printer's default settings, you'll get a paperweight with a mushy top.

**RESIZING**
At 100%, the ornament is a nice size for larger trees – especially for the base of the tree where you'd expect larger ornaments. However, you can scale this down to 50% and still get nice prints. At that size, the ornament looks good on miniature trees. I haven't tried printing it larger than 100%.

**PRINT TIME**
With my settings, it will take about 4.5 hours to print at 100% scale. At 50%, it takes a little over an hour.

**COLOR-CHANGE PLA**
I used TTYT3D's quick color change PLA. If you print one ornament with it at 100% with it, you'll get a subtle color change. For a more dramatic change, like in the size comparison photo, print several ornaments at once. To go all the way from gold to blue, you'll need the estimated print weight to be at least 75 grams (4 ornaments at 100%).

**HOW DO YOU HANG IT?**
I've concealed attachment points one the back of one of the points of the star. Just tie a piece of coat thread to them to create a loop.

**PRINT SETTINGS**
You'll generally want to print this at the lower end of your PLA's temperature range. I print TTYT3D PLA at 180 degrees, which is well below their recommended temperature. Maybe my printer just runs hot, but that temp prints more accurately with less stringing.

*Thickness*

* Layer thickness: .15mm
* Wall thickness: 0.4mm and choose the “alternate extra wall” option so it alternates between 0.4 and 0.8mm walls with each layer (if you're using Cura – other slicers may not have this option). The alternate extra wall seems to prevent gaps in the print while minimizing the overall weight of the ornament. If you print below 75% scale, I suggest printing at 0.4mm without the alternate extra wall. I would also print without the alternate extra layer if you're using transparent filament.
* Top/bottom thickness: 2 layers for opaque filament, 1 for transparent filament
* Initial bottom thickness: 3 layers

*Infill*
This doesn't need any infill. Seriously.

*Speed*
You'll want to use slow printer settings to that the print is accurate and to reduce the pull on the thin arms of the topper.

* Overall: 60mm/s
* Outer wall: 40mm/s
* Inner wall: 50mm/s
* Travel Speed: 100mm/sec

*Build Plate Adhesion*
I printed with just a skirt and it worked well every time. If you have difficulty getting the details of the first layer to adhere to your bed, try adding a raft.

*Supports*
I added supports to get the outer points of the ornament to print better, but you can do without them. The supports I added made little difference in print time or the amount of filament used. I found that adding supports on the side with the attachment points (for strings) was problematic (attachment points broke before supports separated) and unnecessary (model printed fine without the supports). So, I added a support blocker to that corner. Support settings:

* Placement: touching Buildplate
* Overhang: 69 degrees
* Pattern: Lines
* Density: 12%
* Enable Support Brim: Yes
* Brim Width: 4mm

*Common Problems*
* Uneven print: Reduce print speed or try scaling the print up in the Z dimension only. Scaling disproportionately may impact how the ornament hangs.
* Mushy print: Reduce print temp, increase cooling, or print more than one ornament at a time. 

Frosty The Snowman

License: Attribution-NonCommercial-NoDerivs
CC BY-NC-ND
***
***Sculpts By @ChelsC423***

An old animated classic, this Frosty pose is made to go hand in hand with his wife Crystal!
[Find Crystal HERE](https://social.thangs.com/m/570424)

***To sell physical printed objects, please see the ChaosCore Partner tier on our Patreon***

***If you would like to support us and receive exclusive to Patron models every month check us out here:
https://www.patreon.com/chelscct***


Tree Topper - Classic

tree-star.stl

festive

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Holiday Hangers: Santa, Snowman & Reindeer Trio

Witch Frog Figurine — Halloween Fantasy Sculpture

Halloween Skeleton Turtle - A Spooky and Fun Toy

Spiral Christmas Balls

FREE-ster Eggs Multi-Pack

Starburst Christmas Ornament

Egg Tealight Cover -Breezy

Festive Lamppost

Jolly Frosty Vase for Festive Decor

Snow Dome Vase - Perfect for Winter Decor and Holiday Centerpieces

Egg Tealight Cover -Bunnies

Christmas Spiral Teardrop 2023

Aussie Snowman

Snowflake Christmas Tree Ornament – Holiday Festive Decor

Open Spiral Christmas Bell

Spiral Teardrop Christmas Ornament

Diamond Christmas Ball

Star Christmas Tree Ornament

Frosty The Snowman

Tree Topper - Classic