Labubu Wall Art

Labubu Art.3mf

XL Highland Cow (standing) for larger build plates above 300x300x300

XL Highland cow.3mf

Vulcanic dragon egg + night light

Dragon egg Part 1.stl

SW Darth Vader, Wall Art

Star Wars Darth Vader_1.stl

XL Bauble

Threaded top.stl

Zombie Hand (Pre-Supported)

ZombieHand.stl

Not So XL Urban Goose, for smaller build plates below 300x300x300

Not So XL Urban Goose 2.3mf

Chains

48 x infinity chain 36in 91mm.stl

SW R2D2, Wall Art

Star Wars R2D2_1.stl

Sunflower

Sunflower.3mf

Yeah, Another christmas Ball

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**ABOUT THE DESIGN**
Yep, this is yet another variation on my Christmas Balls with Integrated Stems. You can't keep a good designer down. There's no photo because my prototype is still printing. Still, it's 80% done and the rest is identical to other prints I;'ve published, so I already know it should work. Give it a try. It's relatively easy to print. 

**RESIZING**
This ornament should scale up well, but I'm not sure how much smaller you could print it using a consumer FDM printer. Using a resin printer, you could probably print it much smaller.

**PRINT TIME**
About 6 hours

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 – 0.8 mm.

I had the best results using Cura setting the default width to 0.4 mm and adding custom settings for the main ball that printed it 0.8 mm thick. You can do this by adding a support blocker to the bottom and giving it custom settings of 0.4 mm. Cura adds the two and prints the area within the blocker at 0.8 mm.

*Infill*
These do not need any infill. JUST DON'T DO IT.

*Speed*
* Outer Wall: 35 mm/sec
* Inner Wall: 40 mm/sec
* Travel SpeeD: 60 mm/sec

*Build Plate Adhesion*
I used a brim. With the supports, you shouldn't need a raft.

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. If you get supports inside the ball, just add a support blocker.

* Support Structure: Normal
* Support Placement: Touching Buildplate
* Support Overhang Angle: 60 Degrees

Spiritual, Know Your Power 1

Spiritual_1.stl

Knight’s Axe Kit | No AMS, No Support, No Glue

Fossil Grey 2.stl

Knight Duck

knight_duck.stl

PLEIADES Soap Cover // 57x83x103

PLEAIDES Soap Cover 57x83x103.stl

Wooden skull mushroom planter

Wooden skull.stl

Fluent Form – A Vase of Flowing Elegance

Fluent Form.stl

MrsHerb- Nomz

MrsHerb Parts 3mf - Nomz.3mf

Skull Heart : Pen holder, Keychain, Decoration

skull heart decoration.stl

GEN2 Decor - Faceplates - Chevron

1W-1H - V2 - Handle.stl

decoration

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Labubu Wall Art

XL Highland Cow (standing) for larger build plates above 300x300x300

Vulcanic dragon egg + night light

SW Darth Vader, Wall Art

XL Bauble

Zombie Hand (Pre-Supported)

Not So XL Urban Goose, for smaller build plates below 300x300x300

Chains

SW R2D2, Wall Art

Sunflower

Yeah, Another christmas Ball

Spiritual, Know Your Power 1

Knight’s Axe Kit | No AMS, No Support, No Glue

Knight Duck

PLEIADES Soap Cover // 57x83x103

Wooden skull mushroom planter

Fluent Form – A Vase of Flowing Elegance

MrsHerb- Nomz

Skull Heart : Pen holder, Keychain, Decoration

GEN2 Decor - Faceplates - Chevron