These are fun rockets with boosters that extend on take-off. I designed two sizes and each contain two parts: the main rocket body and the ‘boosters’.

I've included the following STL models:
Large Rocket (complete)
Large Rocket (body only)
Large Rocket Booster Insert (a set of 4)
Small Rocket (complete)
Small Rocket (body only)
Small Rocket Booster Insert 

3D PRINTING SETTINGS
Layer Height 0.2mm
PLA works great
15-20% Infill

Dimensions of Large Rocket: 4in x 2 3/8in
Dimensions of Small Rocket: 3 1/4in x 1 7/8in

*Supports are needed for the larger rocket at the base around the outside rings of the boosters.  (Make sure not to include supports inside the booster chambers because you need to keep those clear to drop the boosters in when you pause the print:)

There are two ways you can print these rockets:
1. Print the complete rocket 
2. For different color rocket and boosters, print the boosters first, print the rocket second pausing at layer height 15.6mm for the large rocket and 30.6mm for the small rocket, drop the boosters in and then continue printing. 

Have fun printing these…they’re a blast 🚀

Rocket with Boosters (2 sizes)

Large Rocket (complete).stl

Get commercial license and download newest models cheaply- https://www.patreon.com/goodesign

Version 1.1 Fixes
I modified the connecting parts so that the display stand can fit and support the airplane properly.
Anyone who previously purchased and printed the F-16 can print and install the 1.0 connection part of the display stand.
Anyone who purchases the newly modified F-16 version 1.1 can print and install the 1.1 version connection parts on the display stand.

This is a stand to display the F-16 I designed.
Like the display stand I designed previously, it can be tilted left and right and has a drawer to store the landing gear.

To give a greater sense of speed, curved surfaces were added to the sides.

https://youtu.be/jATjuWHK7OQ?si=b8OB5wVFEhfU2vIv

I hope this display stand will give you a great display of your F-16 falcon design!

download F-16 Falcon - 

Largest part in printing, size = X 100mm, Y 130mm, Z 110mm, After full assembly size= X 100mm, Y 115mm, Z 141mm

Total Build Time : 17h 45m / Plastic Weight : 76g
Design by GOODesign

F-16 Display stand V 1.1

GOODesign_F-16_Display_Stand.stl

Many Fab365 military aircraft enthusiasts showed great response to the recently created F-16. Thank you all.
Based on those expectations, I created an armed set this time. It seems that military airplanes only become cool when they are equipped with weapons.

The assembly process is very simple, just refer to the photos and videos.

https://youtu.be/2pnRVWQ-RhI?si=bJztXDkHtq9RK4Rj

Next, I'm working on a display stand, so look forward to that too.

We hope you will make Fab365's F-16 even more stylish with this weapons set.

Go to see F-16 Fighting Falcon A/C - https://than.gs/m/1513100
Go to see F-16 Display stand - 

1 : 48 scale
Design by GOODesign

F-16 Armament set

GOODesign_F-16_Fighting_Falcon_Fuel-Tank.stl

Get commercial license and download newest models cheaply- https://www.patreon.com/c/goodesign

This is a Display Stand for the F-5E that I designed.

Of course, airplanes can be fully displayed and appreciated only with this display stand.

Like the previously designed Display Stand, there is a drawer to store the landing gear.

And you can also change the angle left and right.

Of course, you can connect this Display Stand even while armed.

Please check the video for details.
https://youtu.be/tMpIqwjbyXk?si=bto-8yNw-ZD9R322

I hope you can display and enjoy the F-5E I designed with this Display Stand.

This design does not include the F-5E fighter. For the F-5E fighter, please see the link below!
Download F-5E - https://than.gs/m/1492963

F-5E Display Stand

GOODesign_F-5E_STAND.stl

Get commercial license and download newest models cheaply- https://www.patreon.com/goodesign

The F-5E, which I designed this time, was developed as a low-maintenance aircraft and was operated in many countries for a long time. That's why it's a fairly popular airplane. In particular, it appeared as the aircraft used by the main character in the Japanese animation Area 88, proving its popularity.

It's very easy to make, but there are a few caveats.
1. Be sure to remove the support first.
2. To balance the aircraft, AAA batteries to act as weights can be placed under the cockpit. However, for those who are concerned about battery fluid leaking out after a long period of time, we have attached an STL in the shape of an AAA battery, so you can print this and insert it. but. When you want to print and use it, you must print it with 100% infill to act as a weight.
3. The nose radome must be attached to the fuselage with the arrow pointing upward.
4. When assembling the fuselage and wings, pay attention to the shapes of the projections and grooves, align them, and push the wings all the way to the front of the fuselage, then insert the rear part of the fuselage.
5. The flap and aileron hinge at the rear of the main wing must be installed with the center protrusion facing outward. Please check carefully.
6. When installing a horizontal tail wing, you must first insert the hinge part into the wing and then insert the wing into the fuselage.
7. When installing the tire parts of the front landing gear, you must spread the tire parts with force before inserting them. The landing gear is thin and easily broken, so be careful when applying force.

Please check and refer to the video for detailed process.
https://youtu.be/3oaY3Xa5XRc?si=ivuq5sdR4jst86SF

As with other military airplanes, we plan to design an armament set and stand. We hope to receive a lot of response from you all.
Download Display stand - https://than.gs/m/1492964

airplane

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Rocket with Boosters (2 sizes)

F-16 Display stand V 1.1

F-16 Armament set

F-5E Display Stand

F-5E Tiger II