Bambu Lab A1 Series Hotend & Silicone Sock Holders V1

10 A1 NOZZLE + SOCK.step

Stationary / Utility Toolbox

Sketch N' Design Stationary_Utility Toolbox.STL

Dojo Desktop Caliper Mounts

Dojo Desktop Caliper Mounts_Front Facig_0420_52_1440_001.stl

Wallfinity 1.1

Wallfinity - Base - 50mm -  4x1.stl

Segmented tray with sloped edges (many configurations 2x2, 4x4, etc) 

segmented-tray-v1-h20-50x50-3x3-154x154mm.stl

Steampunk Workshop (Pre-Supported)

SW_Bridge_Complete_WChains.stl

Blacksmith's Workshop Set (Pre-Supported)

WorkingTable_B.stl

Clamp-On Vise - Fully 3D Printable

Frame.stl

Power Strip Holder

Big Power Strip Mount Open Frikarte3D.stl

Buddy Bear

Buddy Bear.stl

Kris Bear

Kris Bear.stl

The North Pole

snow.stl

Henry Hoover Hose Accessory Collection

blank clip.step

ParkTool AWS-10 belt holder LONG VERSION

Keep your tools close at hand with this belt clip/holder For Park Tools AWSS-10 hex wrench set - also knowns as the best hex wrench set known to man.

Simply slide it onto your belt, pocket or other piece of clothing, slide the tool down and it's alwayss close without taking up space in your pocket or you putting grease in them.

To release the tool simply slide it upwards or to either side. Secure enough for running and jumping in the workshop - perfect for the stressful life of a home or workshop bike mechanic.

This version works great for pockets or other fabric lower than your waist, will make a longer version so you don't have to lift your shirt as often.

This version is longer and therefor interferes less with your shirt when worn on your belt

See orignal/shorter model at:  https://thangs.com/designer/Flaska/3d-model/Park%20Tool%20AWS-10%20belt%20clip%2Fholder-932562?manualModelView=true&source=mymodels

Soldering wire stand (Print in place)

Really proud of this one. Soldering wire stand with print in place hinge and metal shaft slid into a hole. supports most sizes of soldering wire spools, many spools can be installed at once. If you want to access the spools, just lift the metal shaft up. If a small wire spool is installed, there is always more room for insulation tape, scotch tape etc
it works incredibly smoothly and is very strong. the bottom of the stand is corrugated so it grips nicely to a rough desk but there are also round holes for rubber pads.
The middle section has all the main lead exposure health hazards noted down for when you'll inevitably forget about them from all the lead fumes you have been inhaling. The sides have tin and lead elements decals.

_The model is supposed to be printed laying down with the hinge's shaft touching the build plate. The orientation here is very important so that the hinge works properly. I printed mine with .6mm nozzle at .14mm layer height and 10% infill. it's very strong and the letters & decals and perfectly readable. No brim and only one support for the shaft slot on the left side.
After printing, a ~10cm long, 10mm wide shaft is supposed to be pushed into the hole above the hinge. If you dont have a metal shaft, you can always 3d print one though it wont look as neat._

Park Tool AWS-10 belt clip/holder

Keep your tools close at hand with this belt clip/holder For Park Tools AWSS-10 hex wrench set - also knowns as the best hex wrench set known to man.

Simply slide it onto your belt, pocket or other piece of clothing, slide the tool down and it's alwayss close without taking up space in your pocket or you putting grease in them.

To release the tool simply slide it upwards or to either side. Secure enough for running and jumping in the workshop - perfect for the stressful life of a home or workshop bike mechanic. 

Tools and parts tray for bike mechanic stand

##A tray for bike mechanic stands with compartments for:
 (-)Brake cleaner (or bottle of something else)
 (-)Grease jar
 (-)small items
 (-)Bigger items
 (-)Easy access pedal washer holder
 (-)Pedal holders
 (-)All your favourite allen and torx keys

It attaches to the bike stand with four m6 screws and nuts. Holes are made for m6x20mm but you can easily fit longer screws without cutting them.

###Print settings
 (-)No rafts/supports
 (-)2mm layer height
 (-)20% infill
 (-)I went with an X-pattern for infill but others probably work as well
 (-)PETG for longevity

If you want the model in another format please contact me.


Pedal display or workshop stand

A pedal stand for display or workshop I made for my workshop. It's modular and has room for one to an infinite number of pairs. Simply slide the different mating pieces into eachoter to build a longer rack.

It comes with countersunk holes prepared for mountaing and has easy access slots for pedal washers so you don't lose them.


 Photos are the current design version printed with:
0.4 resolution
Max speed
PLA

Final version is currently printing in PETG to get a nicer, more durable product.

Modular Air Tool Organizer

HolderBaseLabel.stl

The Basement Buddy

The Basement Buddy.stl

Workshop

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Bambu Lab A1 Series Hotend & Silicone Sock Holders V1

Stationary / Utility Toolbox

Dojo Desktop Caliper Mounts

Wallfinity 1.1

Segmented tray with sloped edges (many configurations 2x2, 4x4, etc)

View 14 new models

View 20 new models

Clamp-On Vise - Fully 3D Printable

Power Strip Holder

Buddy Bear

Kris Bear

The North Pole

View 24 new models

ParkTool AWS-10 belt holder LONG VERSION

Soldering wire stand (Print in place)

Park Tool AWS-10 belt clip/holder

Tools and parts tray for bike mechanic stand

Pedal display or workshop stand

Modular Air Tool Organizer

The Basement Buddy