Escapement Demo FREE

Escapement Fidget (v8~recovered)_Escapement Fidget (v8~recovered)_Spur Gear (74 teeth)_1_Body1.stl

I Love 3D Printing Gag Gift Mug

Clogged nozzles, layer shifts, poor layer adhesion… anyone familiar with 3D printing will recognize these!

See here for video: https://youtu.be/FJbw00gRW_4  

Are getting or giving a 3D printer this holiday season? This model is the perfect first print! Just hit print and walk away. Any flaws will only make it better!

3D designing and printing teaches us to expect mistakes, plan for them, fix them and try again. If you are new to 3D printing, you can expect to have more than a few prints that come out looking something like this mug.

Disclaimer: All flaws in this model are intended and don’t represent the quality of the brands shown! Lulzbot makes excellent printers and eSun makes excellent filament. Both are great options for avoiding the 3D printing pitfalls that you see in this print!


Torture Calibration Test

Mini Test Cube

Social Media Calibration Cube - Flex your precision!

Calibration_Cube_Social_Medias_V1.step

XYZ_CallibrationCube.stl

This is a small and simple XYZ calibration cube for checking the dimensional accuracy of your printer.   The cube has X, Y and Z written along their respective axes.

Once printed either use an accurate ruler or callipers to measure the dimensions of the print. The original model size is 20mm*20mm*20mm however you may wish to resize it to be bigger (or smaller). 

Once you have measured your dimensions you may want to adjust the steps or steps per mm for each axis in your printers firmware - This may or may not be possible depending on your printer. 

To do this you will need to find your current Steps per mm, and then have your observed dimension and expected dimension.

To calculate the new Steps per mm you will need to do:

(Expected/Observed)*Current Steps per mm = New Steps per mm

It is also good as just giving a gauge of how well your 3D printer works with small over hangs and flat faces to check for Z-Banding or ghosting!

Calistar (formerly Fleur de Cali) - Open source printer size and skew calibration

calistar_120x3.stl

Gridfinity Ikea Alex Drawer - Light Locking Base - 10x7 Grid

GridfinityBaseplate - IkeaAlexTall - 10x7 - Bottom Left.stl

FuzzyRing (Easy Print .3mf) - Fuzzy Skin Sample *by RNDM3D*

FuzzyRing_0.8_v1.0_PRECONFIG.3mf

Easy Torture test -Torture Cube

This is a very easy very simple torture test to see the dimensional accuracy of your print and also slightly test your overhangs!!
This is a small ornate "cube" which can be printed in about 30-50mins depending on your settings.
I print one with faces parallel to the axes and then another at a 45 degree angle to test the diagonals of the printer.


Bearded Gnome

BeardedGnome.stl

XYZ Calibration Test - Vase Mode

Quick 10 minute print - 0.3 m of filament

Don't waste your precious time and filament printing a so called “calibration cube”!

This quick print provides clues for all the important features and settings:

Extrusion width
E-steps / rotation distance (X, Y, Z)
Bridging
Cooling
Overhangs
Speed / accelleration
First layer / bed adhesion
Retraction (stringing test, seam test)
Preassure advance / linear advance
Print Settings
1 perimeter
0.2 mm layer hight
3 bottom layers
Disable “Ensure vertical shell thickness” (PrusaSlicer)
No Infill, top layers, brim or supports

**Troubleshooting**
https://www.reddit.com/r/3Dprinting/wiki/troubleshootingandcalibration

Some quick tipps:

_**Extrusion width**_
Check if the thickness of one of the outside walls at the top matches the setting in your silcer
**_E-steps / rotation distance (X, Y, Z)_**
If the outside dimensions are not 20 mm but way off, correct the settings for the affected axis
**_Bridging / cooling_**
If the bridging perimeters in the top center are drooping/sagging, check cooling an bridging settings in your slicer
45° overhangs
If the perimeters in this section are drooping/sagging, check the part cooling and cooling settings in your slicer
**_Speed / accelleration_**
ringing, bulged corners - you may want to reduce speed and/or accelleration (also see Preassure advance / linear advance)
**_First layer / bed adhesion_**
If there are problems with the print adhering to the bed, check if
- the bed is level and parallel to the x-axis
- the bed is clean - no dirt or grease
- the bed temperature is correct
If the print is wider at the bottom (first few layers) than at the top, check your z-offset and first layer settings
**_Retraction (stringing test)_**
If you experience stringing, check your retraction and cooling settings
**_Preassure advance / linear advance_**
If large seam gaps or bulged corners appear, consider tuning your printer firmware settings for preassure advance (Marlin) / linear advance (Klipper)

XYZ Calibration Test

FabbEgg - The threaded surprise egg, that is easy to print, and SOOOOOO satisfying.

Fab Egg - Surpise Egg Full Model.stl

2:1 GEAR RATIO TOLERANCE TEST PRINT

Spur Gear (32 teeth).stl

Filament swatch and tracker

TPU Mustache Stick Man - TPU and PLA Test Print

This stick man is a remixed version of our original TPU stick man, only this one... has a mustache! (and a hat) [Here is a link to the original stick man](https://thangs.com/designer/DR%203D/3d-model/TPU%20Stickfigure%20-%20TPU%20Test%20Print-879130?manualModelView=true&source=All+Files). 
This print is a good way to test your TPU. After the stickman prints, you can color in the eyes and the mustache to give it some pop.
If you like this model, you know what to do... hit that like button!
Make sure to follow us so you get notified when we upload a new model!
Find us on Printables [here](https://www.printables.com/@DR3D_20233D)
Find us on Instagram [here](https://www.instagram.com/dr_3d2023/)

Testlement

Testlements are small, simple test prints that are great for showing off your filament collection. (Named after their likeness to battlements and being test prints) Testlements are designed to use only a few grams of filament, making them economical and eco-friendly. They are also easy to print, requiring no supports or rafts. You can print Testlements in different sizes, colors, and materials, mix and match them, and even pop them together in groups (as shown in pics). 
Testlements are fun and useful test prints that let you test your 3D printer settings and showcase your filament choices. (Making them Great for showcasing filament choices for prints on places like Etsy) Try them today and see how they can transform your 3D printing experience.

Calibration Measurements:
20 mm wide and long (at its largest points)
22 mm tall

Print Settings:
.1 mm layer height
no supports


The Oh the Horror Cube

Test Bridge

thangs valentine's day contest I heart benchy love lock

benchy_lock_complete.stl

chess.stl

This is a **chess pawn** I made myself in blender. You can use this as a **test print** for your 3D-printer or just print this for fun.

Test print

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Escapement Demo FREE

I Love 3D Printing Gag Gift Mug

Torture Calibration Test

Social Media Calibration Cube - Flex your precision!

XYZ_CallibrationCube.stl

Calistar (formerly Fleur de Cali) - Open source printer size and skew calibration

Gridfinity Ikea Alex Drawer - Light Locking Base - 10x7 Grid

FuzzyRing (Easy Print .3mf) - Fuzzy Skin Sample by RNDM3D

Easy Torture test -Torture Cube

Bearded Gnome

XYZ Calibration Test - Vase Mode

FabbEgg - The threaded surprise egg, that is easy to print, and SOOOOOO satisfying.

2:1 GEAR RATIO TOLERANCE TEST PRINT

Filament swatch and tracker

TPU Mustache Stick Man - TPU and PLA Test Print

Testlement

The Oh the Horror Cube

Test Bridge

thangs valentine's day contest I heart benchy love lock

chess.stl