ATX motherboard test stand

Drive an M3 screw through the center hole to use it to locate the motherboard in position. It is possible to put the rest of the screws in but I don't plan to use them, my objective is to prevent the stand from slipping away accidentally while doing testing/troubleshooting.

I might expand on this to use threaded inserts instead and attachments to hold PSU, HDD, or support heavy PCIE components like GPU.

*****
Want to buy me a coffee?
https://www.buymeacoffee.com/zer0s

Clicking on my affiliate links below will give me a small kickback if you purchase something. (at no extra cost to you)

AliExpress affiliate link:
https://s.click.aliexpress.com/e/_DeAZr9P

*****
Consolidated affiliate links of other 3D printing-related items:
https://wp.me/peMLu6-j

For Amazon affiliate links
https://wp.me/peMLu6-2C

Art Deco Wings Switch Dock

Switch_ArtDeco_Wing_Holoprops.stl

GamerSupps Waifu Cup Stand with LED Channels

This is a raised cup stand with LED gaps on each side to run LED strip under.

GamerSupps Waifu Cup StandLED Channels

MUNBYN LABEL HOLDER V2

As with all of my projects, I wasn't completely happy with the other solutions. When I started this project I knew I wanted to make it easier and quicker to print. This was designed to be used with Munbyn printer labels but should also work with other brands. In this version, I have reworked the sides and added a tray up top to save space on your desk.

**NEEDED HARDWARE**
4 - M4-0.7 x12mm Flat Head Screws

**3D PRINTING SETTINGS**
Layer Height - 0.2mm - 0.3mm
Material - PLA, PETG, ASA, ABS

Roller should be the only part that needs supports. The other parts make sure they lay flat.

Lower Tray.stl

NZXT inspired headphone stand

I designed this a long time ago to mimic a headphone holder NZXT designed that stuck to the front of their PC cases

Hex paint bottle rack

2 - 17ml bottles.stl

Zørp-O'-Lantern Bust Stand

Here's a nice stand for your [Zørp-O'-Lantern head](https://than.gs/m/939862) ([alt](https://than.gs/m/941237))! The neck is angled so you can make the head tilt in different directions based on how to orient it.

Swap filament at 2mm to distinguish the base from the neck. You can glue the head in place or just leave it loose on the stand.

Photographed model was printed at 180% scale using [Polymaker PolyTerra Matte PLA](https://amzn.to/3PHOxFA) ([US direct](https://bit.ly/polyTerra))

2 Controller and Headset Wall Mount

2 Controller Headset Mount v2.stl

Controller and Headset Wall Mount v2

Controller Headset Wall Mount v2.stl

2 Controller Wall Mount v2

2 Controller Wall Mount v2.stl

Controller Wall Mount v2

Controller Wall Mount v2.stl

Foldable Laptop Stand

Stand_Fold_V2_SIDE.stl

Soldering wire stand (Print in place)

Really proud of this one. Soldering wire stand with print in place hinge and metal shaft slid into a hole. supports most sizes of soldering wire spools, many spools can be installed at once. If you want to access the spools, just lift the metal shaft up. If a small wire spool is installed, there is always more room for insulation tape, scotch tape etc
it works incredibly smoothly and is very strong. the bottom of the stand is corrugated so it grips nicely to a rough desk but there are also round holes for rubber pads.
The middle section has all the main lead exposure health hazards noted down for when you'll inevitably forget about them from all the lead fumes you have been inhaling. The sides have tin and lead elements decals.

_The model is supposed to be printed laying down with the hinge's shaft touching the build plate. The orientation here is very important so that the hinge works properly. I printed mine with .6mm nozzle at .14mm layer height and 10% infill. it's very strong and the letters & decals and perfectly readable. No brim and only one support for the shaft slot on the left side.
After printing, a ~10cm long, 10mm wide shaft is supposed to be pushed into the hole above the hinge. If you dont have a metal shaft, you can always 3d print one though it wont look as neat._

Hot glue gun stand.stl

Simple Hot glue gun stand designed to be screwed into a side of a desk (3cm thick desk in my case). The hole at the bottom can be plugged with a metal cup (like a glass jar lid) which will collect dripping hot glue without damaging the plastic shell

I printed mine with abs with some tree supports for the top part. no brim needed

Stand for Illusion Cube V2

Illusion Cube V2 - Stand.3mf

Patterned dish set

dish.stl

Switch Case and Game Stand

This Switch Case and Game Stand is perfect for any gamer who is looking to organize their gaming setup. This stand allows you to hold up to 6 switch cases and 6 switch games. 

Dremel Bits Holder MAX

More places for more of your little bits!  

Dremel Stand and Bit Holder

Dremel holder with more places for your little bits!  

Prints with no supports!

STand

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

ATX motherboard test stand

Art Deco Wings Switch Dock

GamerSupps Waifu Cup Stand with LED Channels

MUNBYN LABEL HOLDER V2

NZXT inspired headphone stand

Hex paint bottle rack

Zørp-O'-Lantern Bust Stand

2 Controller and Headset Wall Mount

Controller and Headset Wall Mount v2

2 Controller Wall Mount v2

Controller Wall Mount v2

Foldable Laptop Stand

Soldering wire stand (Print in place)

Hot glue gun stand.stl

Stand for Illusion Cube V2

Patterned dish set

Switch Case and Game Stand

Dremel Bits Holder MAX

Dremel Stand and Bit Holder

View 16 new models