I have had this idea for a ‘fried egg’ fidget fabric/drink coaster for a little while. I loved the idea of using mesh fabric in the fried egg to give it flexibility and make it feel more ‘egg-like’. The egg shell with the magnets is a fun fidget in itself. The egg tray and egg carton give you an option for how you would like to store your eggs 🥚🥚 
(**You will need fabric and magnets for these prints - see details below 👇)

Dimensions of Fried Egg: 5 in. diameter
Dimensions of Egg Shell: 3 in. x 2 ¼ in.
Egg Tray: 5 in. x 5 in. x 2 ¼ in.
Egg Carton: 5 in. x 5 ½ in. x 3 ¼ in.

PLA works great
Layer Height 0.2mm
Infill 10-15%
Smooth print plate recommended for Fabric Fried Egg
Supports needed for: small half of Egg Shell, Egg Tray and Egg Carton

**Other items you will need:**
Polyester Mesh Fabric (Mosquito Netting)
6x3 Neodymium Magnets (4 magnets per egg shell)

Here is an Amazon link for these items: https://amzn.to/4ca7hq2

A note about fabric: I have tried several different types of fabric. Polyester Mesh fabric (also called Mosquito Netting) is my favorite. I have found that mesh made from PE (Polyethylene) tears very easily. Tulle also is not very durable and tears very easily. Nylon mesh will also work but it is thicker for the print head to print over and I think if you have never printed with fabric before you will feel more comfortable using Polyester Mesh instead.

How to print the Fried Egg: I recommend slowing the print speed to 50% initially to get a really clean first layer. Pause the print at layer height 0.6mm to lay a piece of mesh (that has been cut about an inch wider in diameter than the print) over the print. I like to secure the fabric down with blue painters tape. You can also use magnets. Resume the print at that slower 50% speed for a layer or two and then you can increase the speed back up to 100%. 

To make it multi-color, pause the print at layer 13 (layer height 2.6mm) to change out the filament to a new color (see photo).

How to print the Egg Shell: You will need (4) 6x3 neodymium magnets for each complete egg. To insert the magnets, pause the print at layer height 3.6mm - when it pauses you can add the magnets. Make sure the orientation is correct so that the two halves of the print will attract to each other when done:)

How to print/assemble Egg Tray and Egg Carton: The Egg Tray and Egg Carton Bottom both need supports. The Egg Carton Lid needs supports and a brim. (I like brim on the lid as an extra precaution to prevent warping.) Use the small peg to attach the pyramid piece to both the egg tray and egg carton bottom. The hinge is attached (prints in place) to the egg carton bottom. To attach the carton bottom to the lid, pop the loose part of the hinge into the matching part of the lid. Lastly, fold/bend the tab of the carton bottom up so it can slot into the corresponding hole of the lid when closed.

My designs are free for personal and non-commercial use. If you would like to sell them for commercial use, send me a message and we can discuss the details:)

If you like my work and want to help support it, you can buy me a Diet Coke at https://www.buymeacoffee.com/3dpmom Thanks so much!

Fidget Fabric Fried Egg Set (play or coaster set)

Egg Tray.stl

I recently released my ‘Mega’ Magnetic Tile Haunted House Collection but have been wanting to make a playful, scaled down version - so here it is 👻 This is my ‘Mini’ Magnetic Tile Haunted House that is ¼ the scale of my original. For extra fun, many of the windows have 2-sided window panes that rotate, there's a skeleton that greets you behind a hinged front door, tombstones to decorate the front yard and all the spiders, cats, rats, ghosts and skeletons you can handle 🕷🎃🐈‍⬛🐀👻 (These tiles are compatible with store bought magnetic tiles just fyi:)

****3D Print Settings****
PLA Filament
Layer height 0.2mm (for some of the more detailed pieces - like the rat windows and tombstones you can use a 0.16 layer height if preferred)
Infill 15%
Brim may be needed on larger pieces (like the 150x75 walls) if you notice any warping

****Neodymium magnets needed: 20x5x2 ****

- I specifically designed all these pieces to work with this size magnet

- Here is a link to these magnets on Amazon: ****https://amzn.to/3Nibhd3****

- Magnetic build plate highly recommended but not absolutely necessary.


****Printing Instructions for Inserting Magnets and Filament Pieces:****

- Every piece in this collection (except for the Porch Pillars and the Chimney Cap) need to be paused at layer 30 (layer height 4.8mm) to insert magnets. 
- The Front Door piece and all the window panes that rotate also need cut pieces of filament placed in the ‘filament chamber’ areas (see photos and video). 
- It helps to straighten the filament pieces that will be inserted into these pieces.  I have designed a separate 3D printed device to do that (I call it the ‘filament straightening block’) and will link a video below.

- After the magnets/filament are inserted, resume printing

****I have also included a 3mf print profile with the following print plates:****
Print Plate #1 Mini HH_75X75_Front Door: 4 colors, pause at layer 30, cut and insert filament pieces to fit into filament chamber areas
Print Plate #2 Mini HH_75x75_Curved Cat & Ghost Window: 4 colors, pause at layer 30; cut and insert filament pieces to fit into filament chamber areas
Print Plate #3 Mini HH_75x75_Curved Spider & Ghost Window: 4 colors, pause at layer 30; cut and insert filament pieces to fit into filament chamber areas
Print Plate #4 Mini HH_75x75_Curved (Plain) Window: 3 colors, pause at layer 30
Print Plate #5 Mini HH_75x75_Rectangle Spider & Ghost Window: 4 colors, pause at layer 30; cut and insert filament pieces to fit into filament chamber areas
Print Plate #6 Mini HH_75x75_Rectangle Pumpkin & Ghost Window: ****5 colors!!****, pause at layer 30. Cut and insert filament pieces to fit into filament chamber areas.
This is the only piece with 5 colors. You will notice I colorized both the ghost and the pumpkin white.  After the white is done printing the ghost you will need to change out the white filament for orange before it starts printing the pumpkin.  Pause the print if needed to do this (on my Bambu printer I can do this while printing).
Print Plate #7 Mini HH_75x75_Rectangle (Plain) Window: 3 colors, pause at layer 30
Print Plate #8 Mini HH_75x37.5_Curved (Plain) Window: 3 colors, pause at layer 30
Print Plate #9 Mini HH_75x37.5_Curved Rat Window:3 colors, pause at layer 30; cut and insert filament pieces to fit into filament chamber areas
Print Plate #10 Mini HH_75x37.5_Plain Wall Panel: 1 color, pause at layer 30
Print Plate #11 Mini HH_150x75_Curved Skeleton & Ghost Window: 4 colors, pause at layer 30; cut and insert filament pieces to fit into filament chamber areas
Print Plate #12 Mini HH_150x75_Curved (Plain) Window: 3 colors, pause at layer 30
Print Plate #13 Mini HH_150x75_Tree Wall: 2 colors, pause at layer 30
Print Plate #14 Mini HH_75x75_Floor Piece: 1 color, pause at layer 30
Print Plate #15 Mini HH_75x37.5_Floor Piece: 1 color, pause at layer 30
Print Plate #16a Mini HH Front Porch: 1 color, pause at layer 30
Print Plate #16b Mini HH Porch Pillars: 1 color, pause at layer 30
Print Plate #17a Mini HH Tombstone Noah&RIP: 2 colors, pause at layer 30
Print Plate #17b Mini HH Tombstone Ben&Waldo: 2 colors, pause at layer 30
Print Plate #18 Mini HH Front Door Awning: 1 color, pause at layer 30
Print Plate #19 Mini HH_75x85_roof: 1 color, pause at layer 30
Print Plate #20 Mini HH_90x85_roof (no chimney): 1 color, pause at layer 30
Print Plate #21a Mini HH_90x85_roof with chimney: 1 color, pause at layer 30
Print Plate #21b Mini HH Chimney Cap: 1 color, pause at layer 30

Have fun printing!

Mini Magnetic Tile Haunted House Collection

(21a) Mini HH_90x85_roof with chimney.stl

These are the railing, pillar, arch and beam pieces for the magnetic tile haunted house. 

****3D Print Settings****
PLA Filament
Layer height 0.2mm
Infill 15-20%
No supports needed (see recommendations for brims below)

****Neodymium magnets needed for arches and railings: 20x5x2 and 10x5x2****
****Neodymium magnet size need for pillars: 12x5x3 OR 10x5x2****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the magnets needed for this print:
https://www.amazon.com/shop/3dpmom

****Arches****
Neodymium magnets sizes needed for the arches: 20x5x2 and 10x5x2 (I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers.)
I recommend brims for the arches to prevent warping at edges.
For the arches, add a pause print at layer height 6.0mm to insert the magnets. When the print is paused insert the magnets.  I like to alternate these two size magnets between the magnets holes (20x5x2, 10x5x2,20x5x2, 10x5x2, etc.).  I found if I used all 20x5x2 they were too strong and if I used all 10x5x2 it felt a little too weak.
After the magnets are inserted, resume the print.

****Railings****
Neodymium magnet size need for railings: 20x5x2 and 10x5x2
Brims are not needed for the railings.
Add a pause print at layer height 6.0mm to insert the magnets.  I like 20x5x2 for the magnets at the bottom of the railing and 10x5x2 for the magnets along the side of left and right railings. Insert magnets, then resume print.

****Pillars****
I recommend a brim for the pillar body/base piece because it is tall.  The brim will help add stability. 
Add a pause print at layer height 6.0 mm to insert the magnets. Insert magnets, then resume print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Railing Pieces): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #2 (Pillar Pieces): one color, pause inserted at layer 30 (layer height 6.0mm), brim added to base/body piece
Print Plate #3 (150x150 Arch Wall): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #4 (150x150 Arch Wall with Notch): one color, pause inserted at layer 30 (layer height 6.0mm) 
Print Plate #5 (Beam Piece): one color

Have fun printing!

Magnetic Tile Haunted House RAILINGS, PILLARS, ARCHES & BEAMS

Right Porch Railing.stl

**Don't forget to ❤️, add to a collection, and follow SUNA for more fun creations!**
___
This is probably not the first clean/dirty dishwasher magnet you've seen, but ~it is the coolest~ this one doesn't contain death crystals! A simple, easy way to keep track of your dishwasher - as long as you remember to flip the sign you will no longer have to guess & inspect dishes to figure out if it was run. There is also a blank sign for you to add your own text! Check the attached YT video to see a quick tutorial on adding negative modifiers like text to a model!

**Dimensions**:  100 x 60 x 4 mm (~3.9 x 2.4 x .16 in)

**Weight**: ~19g + 1g waste

**Additional Items**: You will need 2x Magnets, sized ~20x5x2. You can find them [here on amazon](https://www.amazon.com/gp/product/B07Q6564FB/).
Note that tolerances are loose on these magnets so if one does not fit well just try another from the set. You may also try a little glue if you have any issue with them coming loose. 

___
**PRINTING**:
- Clean your build plate! "Flat" models like this are more likely to shrink and peel up. 
- Print from either side. I prefer design face down on a nice textured plate like the cryo plate
- Print with at least 5 bottom & top shell layers, 2-3 walls, 0-20% infill
- 3mf included with all three designs and a layer change added at z=1.2mm (layer 6 for .2mm layers)

___
‼️ All models are the exclusive intellectual property of SUNA. SUNA models are protected under applicable copyright laws and international treaties. Unauthorized sharing, distribution, reproduction, or sale of these models in any form is strictly prohibited.

Users are granted limited rights to download and use models for personal, non-commercial purposes only. Any commercial use of these models, including but not limited to selling, modifying for sale, or redistribution, is strictly forbidden unless the user subscribes to a valid Thangs license with Commercial Rights.

Magnetic Dishwasher Sign - CLEAN | DIRTY

display_magnetic_clean_dirty_curlytext.stl

display_magnetic_full_set.3mf

These are the window board pieces for the magnetic tile haunted house. 

I designed these to be used with 6x2 neodymium magnets.  I strongly recommend using these size magnets. When inserted into the print, these magnets do not have space within their 'chambers' to rotate. These window board pieces (as well as the light base piece) are the only pieces designed this way BUT all the other magnets in my designs rotate so they will orient to the magnets in these pieces.

****3D Print Settings****
PLA Filament
Layer height 0.2mm
Infill 15%
No brims or supports needed
****Neodymium magnets needed: 6x2****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the light and magnets that fit into this print. That's it:)
https://www.amazon.com/shop/3dpmom

For these window boards, add a pause print at layer height 2.8mm to insert the magnets. When the print is paused insert the magnets.  After the magnets are inserted, resume the print.

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Window Boards 1-3): one color, pause inserted at layer 14 (layer height 2.8mm)
Print Plate #2 (X-Shaped Window Boards 1-3): one color, pause inserted at layer 14 (layer height 2.8mm)

Have fun printing!

Magnetic Tile Haunted House WINDOW BOARDS

X Window Board_1.stl

These are the roof pieces for the Magnetic Tile Haunted House. 

****3D Print Settings****
PLA Filament works great
Layer height 0.2mm
Infill 15%
No supports need 
****Neodymium magnets needed for all Roof Pieces (except chimney): 20x5x2 and 10x5x2****
****Neodymium magnets needed for chimney: 10x5x2 OR 12x5x3****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the magnets needed for these prints: https://www.amazon.com/shop/3dpmom
 
****How to Print Roof Pieces****
For the roof pieces , you will need to use 20x5x2 and 10x5x2 neodymium magnets only.  I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers. 

For all of these pieces, add a pause print to insert the magnets as shown in the photos for each design. When the print is paused insert the magnets.    

For the Roof Corner Piece, Roof Dormer Piece,  Roof Deep Dormer Piece and Roof Panel Pieces you will need to ****pause the print twice****: the first pause will be at layer height 7.8mm; the second pause print will be at 87.2mm. 

****Note:**** For the second set of magnets to be inserted at the 87.2mm height you will need to to place a magnet on the outside of the print to hold the ‘inside’ magnet in place. (Otherwise the magnet may ‘jump out’ and stick to the print head.)  

After the magnets are inserted/secured, resume the print. When you are done with the print simply remove the magnets off from the outside of the print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Roof Corner Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #2 (Roof Dormer Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #3 (Roof Deep Dormer Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #4 (Roof Panel Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #5 (150x75 Roof Piece): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #6 (75x75 Roof Piece): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #7 (75x37.5 Roof Piece): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #8 (Chimney): one color, pause inserted at layer 30 (layer height 6.0mm)

Have fun printing!

Magnetic Tile Haunted House: ROOF

Roof Corner Piece.stl

These are the door/door wall surround pieces for the magnetic tile haunted house. 

PLA Filament works great
Layer height 0.2mm
Infill 15%
Brims recommended for front door wall and french door wall  to prevent warping on the corners
****Neodymium magnets needed: 20x5x2, 10x5x2 and 3x5****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the magnets needed for these pieces: https://www.amazon.com/shop/3dpmom

****3D Print Settings****
For the wall pieces,  you will need 20x5x2 and 10x5x2 neodymium magnets to be inserted around the edges. I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers.  
I like to alternate these two size magnets between the magnet holes (20x5x2, 10x5x2, 20x5x2, 10x5x2, etc.).  I found if I used all 20x5x2 they were too strong and if I used all 10x5x2 it felt a little too weak.I recommend 20x5x2 neodymium magnets to be used for the door pieces.

For the 150x150 Large Front Door Wall and 150x150 French Door Wall pieces there is a small circular space for one magnet centered above each arch. Insert a 3x5 neodymium sized magnet into that space.

For the doors, I recommend 20x5x2 neodymium magnets.

For all of these pieces, add a pause print to insert the magnets as shown in the photos for each design. When the print is paused insert the magnets. After the magnets are inserted, resume the print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Front Door Wall): one color, pause inserted at layer 30 (layer height 6.0mm), brim added
Print Plate #2 (Front Door): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #3 (French Door Wall): one color, pause inserted at layer 30 (layer height 6.0mm), brim added
Print Plate #4 (L& R French Doors): one color, pause inserted at layer 30 (layer height 6.0mm)

Have fun printing!

Magnetic Tiles Haunted House: DOORS

150x150 Front Door Wall.stl

If you're looking for a fun Halloween 3D printing project - look no further 👻 These are the floor and/or flat roof pieces for a magnetic tile haunted house. 

3D Print Settings
PLA Filament
Layer height 0.2mm
Infill 15%
Brim recommended on 150x150 floor pieces to prevent warping
****Neodymium magnets needed: 20x5x2 and 10x5x2****
I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers. 
Magnetic build plate highly recommended but not absolutely necessary.

For all of these pieces, add a pause print at layer 30 (layer height 6.0mm) to insert the magnets. When the print is paused insert the magnets.  I like to alternate these two size magnets between the magnets holes (20x5x2, 10x5x2,20x5x2, 10x5x2, etc.).  I found if I used all 20x5x2 they were too strong and if I used all 10x5x2 it felt a little too weak. (See videos)

After the magnets are inserted, resume the print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (150x150 floor): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #2(150x150 floor w/ center magnets): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #3(150x75 floor): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #4(75x75 floor): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #5(37.5x75): one color, pause inserted at layer 30 (layer height 6.0mm)

Here is a link to Amazon for the magnets needed for these pieces.
https://www.amazon.com/shop/3dpmom

Have fun printing!

Magnetic Tile Haunted House Collection: FLOORS

150x150 floor with center magnets.stl

| **Visit** [JERRARI.com](https://www.jerrari3d.com/) for **Instructions** and a complete look at the GEN2 collection 

These are the original Fusion 360 CAD files uses to create the GEN2 Adjustable Steel Sheet Holder.

Magnetic

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Fidget Fabric Fried Egg Set (play or coaster set)

Mini Magnetic Tile Haunted House Collection

Magnetic Tile Haunted House RAILINGS, PILLARS, ARCHES & BEAMS

Magnetic Dishwasher Sign - CLEAN | DIRTY

GEN2 Steel Sheet Holder CAD Files