Give your [IKEA VAPPEBY](https://www.ikea.com/se/en/p/vappeby-bluetooth-speaker-white-gen-3-80517377/) Gen3 Speaker a sophisticated transformation with this GRID kit. This download includes the pictured Cover, Volume Dial (+ Bonus Studio Dial), and Grid Handle. (The power button can be downloaded seperately [here](https://than.gs/m/1274542?affiliateCode=MAKE))

---

**_Printing Guidelines_**

**Handle:**
- 0.16 mm layer height
- 4+ walls, 15%+ infill (use your discretion to make a strong part depending on the filament you use)
- No supports required

**Volume Dial and Cover:**
- 0.16mm layer height
- 2 walls, 15% infill
- No supports required
- For the Volume Dial, start with an opaque filament, and swap to a transparent filament above 2.4mm if you want the sides to light up (I also did a few layers of Black between the white and green to block more light from the front)*

          *For the Studio Dial, start with an opaque filament, and swap to a transparent filament above 8mm (at Z height 11mm if you want it to line up with the cover)

---

**_Assembly_**

**Handle:**
- Use the original screws for the stock VAPPEBY handle to connect this part
- Do not overtighten the 3D printed screw. That will cause the layers to be ripped apart.

**Cover:**
- Print four of the cover pins. Connect them to the back corners of the cover with a 1/4 twist clockwise (You can use pliers if the fit is tight).
- Cover should press fit into the existing rubber holes on the speaker.

**Studio Dial:**
- Optionally print the 'Studio Dial_Indicator' in another color and glue it into the divot on the Dial for an orbiting indicator (the orange dot shown in the photos).

_Feel free to leave a comment if you have any questions!_

---

**Filaments Used in Photos:**
- [Elegoo Rapid PLA+ White and Black](https://shrsl.com/4vqfx) (Also on [Amazon](https://amzn.to/4iioPSQ))
- [Bambu PETG Translucent 'Olive Green'](https://shrsl.com/4vz09)

**Printer Used:**
- [Qidi Plus4 3D Printer](https://qidi3d.com/products/plus4-3d-printer?sca_ref=6089281.BQS8d0sJuF) (Also [on Amazon](https://amzn.to/4jON7VK)) 

*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_*. 

IKEA VAPPEBY GRID Kit // Cover, Volume Dial, and Handle

VAPPEBY_Cover_Grid.stl

**Foldable Nativity Scene - Complete Christmas Collection
**Complete print-ready STL files for minimalist nativity scene with foldable storage
What's Included:

Holy Family: Mary, Joseph, Baby Jesus
Visitors: Three Wise Men, Shepherds
Animals: Donkey, Ox, Sheep
Structure: Bethlehem stable with roof and star (15cm on longer side)
Storage: Compact foldable base for all pieces

Specs:

Joseph: 5cm height, other figures proportionally scaled
Stable: 15cm on longer side
Pre-tested STL files
Resin & FDM compatible
Minimalist faceless design
Layer height: 0.15-0.2mm

**Perfect for Christmas decor, nativity collectors, and 3D printing enthusiasts!**

Nativity Scene STL Files - Foldable Christmas Bethlehem - Holiday 3D Print Models

Woman.stl

[_**V2 is now available HERE**_](https://than.gs/m/1377006?affiliateCode=MAKE)

ITALIC is an eccentric watering can featuring a playful skewed profile. The enclosed container is filled through an opening in the top of the handle, which can also be covered with your thumb while pouring to regulate flow. Like any good fancy designer product, it's slightly awkward to hold. How will you pick it up? :P

**_Printing Guidelines_**

The walls of this container are 1.2 mm thick, and only the handle portion is solid. I suggest printing with a high wall count (5+) to ensure that the thin handle won't snap off.  You also need to ensure that your printer can create watertight models, otherwise this won't be quite as useful. I used default print settings on my Bambu Lab X1-Carbon with ABS and it worked out!

Download includes a version with minimal supports since the handle is unsupported for much of the print, as well as a version of just the watering can. In either case, I would suggest a substantial brim to help with bed adhesion. 

--- 

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Bambu Lab Mint ABS](https://bit.ly/bamFIL).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_


ITALIC (V1) Watering Can

ITALIC_can_supported.stl

The **PLEIADES Soap Cover** is a quick and clever way to elevate your boring soap bottle. This fits bottles up to 57 mm x 83 mm x 103 mm tall with a 28mm opening.

---

My **PLEIADES** series of prints are designed to be printed in vase/spiral mode in your slicer. I suggest printing this model with a **0.4 mm nozzle width**. Adjust bottom solid layers to be 1.6 mm thick (or the maximum number of layers before the hole is covered). No top layers. **Make sure your slicer is not set to close small gaps.** In BambuStudio I set the _'Slice gap closing radius'_ to 0 mm

--- 

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Fillamentum PLA Extrafill Sky Blue](https://bit.ly/FM-xtra) (also at [MatterHackers](https://bit.ly/xtrafill)).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_


PLEIADES Soap Cover // 57x83x103

PLEAIDES Soap Cover 57x83x103.stl

MERIDIAN 001 is a lovely stout pot divided through the center. Pair the design with a filament swap for a striking piece that will surely make both you and your plants happy. BONUS: You can always use these pots as containers for other purposes. Scale as you wish to suit your needs :)

This pot includes a drainage hole on the bottom for growing live plants and pairs well with my [200 mm Floating Drip Tray](https://than.gs/m/1027158?affiliateCode=MAKE) to allow for excess runoff.

There was initially a glitch exporting the STL which caused some extra artifacts on the bottom half of the photographed model. I've since fixed that, but included _'MERIDIAN_001_old.stl'_ as well in case you like that look.

**_Printing Guidelines_**
Default print settings should work fine, though you may want to increase wall/shell count to help with water tightness. I used 3 shells, 8 solid top layers, and 15% gyroid infill at 0.16 mm layer height.

--- 

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Bambu Lab Matte PLA filament](https://bit.ly/bamFIL) (and translucent PETG for the top half of the scaled down example).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_


MINIMAL

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

IKEA VAPPEBY GRID Kit // Cover, Volume Dial, and Handle

Nativity Scene STL Files - Foldable Christmas Bethlehem - Holiday 3D Print Models

ITALIC (V1) Watering Can