Ghost Pop Beads

These “Ghost Pop Beads” snap together to form spooky chains or rings as long as you want! Use for decoration or to accessorize your costume.

See here for video: https://youtu.be/sqHG2kSpsd8 

The pieces are designed to be printed in “Vase” or “Spiralized” mode. The file is optimized for printing with a 0.4mm nozzle. Printing with different nozzle sizes is still possible but will affect the tightness of fit.

Each piece uses approximately 0.4g of material, making this a great design to use up the scraps of filament you have lying around! A full 1kg roll could print approximately 2500 beads, enough to make a chain 50m (164ft) long!

To connect pieces together, simply pinch the bottom end of one piece to open it up. Insert the oval end of the second piece inside and release. The pieces remain connected but can be separated again if needed. Create long chains or rings by adding as many pieces as you want.

Each piece takes approximately 5 minutes to print. It is, however, much more efficient to print multiple pieces sequentially! Setting up spiralized models to print “one at a time” takes a bit of planning as the pieces must be spaced and sequenced properly so that the hot end or gantry does not collide with the finished prints as it moves on to the next print. 

Make the bottom open by setting “bottom layers” to zero. Good build plate adhesion is essential, so ensure that your machine is well calibrated.

This design is entered in the 2023 HalloweenWearable Contest

Similar Designs: 
Pop Bead Garland: https://social.thangs.com/m/513337 
Skull Pop Beads: https://than.gs/m/943349 


Skull Pop Beads

These “Skull Pop Beads” snap together to form spooky chains or rings as long as you want!

See here for video: https://youtu.be/pCv3Yx5U_7k 

The pieces are designed to be printed in “Vase” or “Spiralized” mode. The file is optimized for printing with a 0.4mm nozzle. Printing with different nozzle sizes is still possible but will affect the tightness of fit.

Each piece uses approximately 0.4g of material, making this a great design to use up the scraps of filament you have lying around! A full 1kg roll could print approximately 2500 beads, enough to make a chain 50m (164ft) long!

To connect pieces together, simply pinch the top end of one piece so that the opening becomes oval-shaped. Insert the oval end of the second piece inside and release. The pieces remain connected but can be separated again if needed. Create long chains or rings by adding as many pieces as you want.

Each piece takes approximately 5 minutes to print. It is, however, much more efficient to print multiple pieces sequentially! Setting up spiralized models to print “one at a time” takes a bit of planning as the pieces must be spaced and sequenced properly so that the hot end or gantry does not collide with the finished prints as it moves on to the next print. 

Make the bottom open by setting “bottom layers” to zero. Good build plate adhesion is essential, so ensure that your machine is well calibrated.

Similar Designs: 
Pop Bead Garland: https://social.thangs.com/m/513337 


1.5GB Tangle of 260 Spiderwebs (Loose Strand Density)

Spiderweb-Dia254-Sect24-Span12.stl

Magnetic Tile Haunted House Collection: FLOORS

150x150 floor with center magnets.stl

Magnetic Tile Haunted House: WALLS

 150x150 Wall.stl

Magnetic Tile Haunted House RAILINGS, PILLARS, ARCHES & BEAMS

Right Porch Railing.stl

Magnetic Tiles Haunted House: DOORS

150x150 Front Door Wall.stl

Magnetic Tile Haunted House: ROOF

Roof Corner Piece.stl

Magnetic Tiles Haunted House (PORCH LIGHT)

Porch Light Base.stl

Magnetic Tile Haunted House WINDOW BOARDS

X Window Board_1.stl

1.5GB Tangle of 260 Spiderwebs (Normal Strand Density)

Spiderweb-Dia250-Sect24-Span10.stl

Haunted House Coffin Box 🦇

Plate 4.stl

1.5GB Tangle of 260 Spiderwebs (Tight Strand Density)

Spiderweb-Dia250-Sect24-Span8.stl

Ghost Layered Fidget (2 sizes)

Ghost Layered Fidget (2 sizes).3mf

Dracula Castle

BASE FRONT RIGHT -v01.stl

Spider Web Coaster

Spider Web Coaster.3mf

Haunted House Coaster

Haunted House Coaster.3mf

The Haunted Manor

MAIN HOUSE -v01.stl

Haunted House 2 Bundle

STL Demo Placeholder (Use Master File Instead).STL

Chibi Halloween STL File Drop ~

House.stl

Haunted House

Most Downloaded of All Time

Categories

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Ghost Pop Beads

Skull Pop Beads

1.5GB Tangle of 260 Spiderwebs (Loose Strand Density)

Magnetic Tile Haunted House Collection: FLOORS

Magnetic Tile Haunted House: WALLS

Magnetic Tile Haunted House RAILINGS, PILLARS, ARCHES & BEAMS

Magnetic Tiles Haunted House: DOORS

Magnetic Tile Haunted House: ROOF

Magnetic Tiles Haunted House (PORCH LIGHT)

Magnetic Tile Haunted House WINDOW BOARDS

1.5GB Tangle of 260 Spiderwebs (Normal Strand Density)

Haunted House Coffin Box 🦇

1.5GB Tangle of 260 Spiderwebs (Tight Strand Density)

Ghost Layered Fidget (2 sizes)

Dracula Castle

Spider Web Coaster

Haunted House Coaster

The Haunted Manor

Haunted House 2 Bundle

Chibi Halloween STL File Drop ~