Wearable halloween mask - Lizard - Moving jaw

lizardmask.stl

Wearable halloween mask - Bird version 2 

designed with Halloween in mind and free for this week only! 

Make sure to like and follow to keep free weekly models coming!

To sell physical prints subscribe to thangs memberships. 

Wearable halloween mask - Bird version 1

Axe prop - Print in place!

axe.stl

Voroni Helmet.obj

Bat Glasses || HalloweenWearable

Bat Glasses V1.0 - Frame.stl

Costume Wing Mount - HalloweenWearable

I made this HalloweenWearable to support costume wings! 
It utilized two telescoping poles and can be mounted with sturdy thread. I have it mounted to a posture corrector because I found it provided the best support but the whole setup is extremely light and can be mounted to just about anything that's securely fastened to your body.



Costume Wing Mount 

Awooga Glasses || HalloweenWearable

Awooga Glasses V1.0.3mf

Screw Crown Tight - HalloweenWearable

DO NOT PRINT - Screw Crown .stl

Modular Halloween Headband HalloweenWearable

headband_kwerkshop.stl

Ghost Pop Beads

These “Ghost Pop Beads” snap together to form spooky chains or rings as long as you want! Use for decoration or to accessorize your costume.

See here for video: https://youtu.be/sqHG2kSpsd8 

The pieces are designed to be printed in “Vase” or “Spiralized” mode. The file is optimized for printing with a 0.4mm nozzle. Printing with different nozzle sizes is still possible but will affect the tightness of fit.

Each piece uses approximately 0.4g of material, making this a great design to use up the scraps of filament you have lying around! A full 1kg roll could print approximately 2500 beads, enough to make a chain 50m (164ft) long!

To connect pieces together, simply pinch the bottom end of one piece to open it up. Insert the oval end of the second piece inside and release. The pieces remain connected but can be separated again if needed. Create long chains or rings by adding as many pieces as you want.

Each piece takes approximately 5 minutes to print. It is, however, much more efficient to print multiple pieces sequentially! Setting up spiralized models to print “one at a time” takes a bit of planning as the pieces must be spaced and sequenced properly so that the hot end or gantry does not collide with the finished prints as it moves on to the next print. 

Make the bottom open by setting “bottom layers” to zero. Good build plate adhesion is essential, so ensure that your machine is well calibrated.

This design is entered in the 2023 HalloweenWearable Contest

Similar Designs: 
Pop Bead Garland: https://social.thangs.com/m/513337 
Skull Pop Beads: https://than.gs/m/943349 


HalloweenWearable Mask - Male Version

Designed for the HalloweenWearable contest here on thangs! We are a little late to the party but the masks are ready to go! 

This will be free for a bit longer as we meant to upload much earlier, I hope you enjoy!

WOLF MASK- HalloweenWearable

Hi friends, I also created a new version of the mask with the shape of a wolf's face.
Here too there are holes to insert the elastic to be able to wear it.
Must be printed with supports.
Hope you like it.
HalloweenWearable
#HalloweenWearable

spiderweb tiara - HalloweenWearable

This is my first model for the HalloweenWearable designs. This is a cute Spiderweb tiara that i just absolutely love!! 


Spider Halloween Glasses

Spider Glasses Without Built in Supports.stl

Skull Pop Beads

These “Skull Pop Beads” snap together to form spooky chains or rings as long as you want!

See here for video: https://youtu.be/pCv3Yx5U_7k 

The pieces are designed to be printed in “Vase” or “Spiralized” mode. The file is optimized for printing with a 0.4mm nozzle. Printing with different nozzle sizes is still possible but will affect the tightness of fit.

Each piece uses approximately 0.4g of material, making this a great design to use up the scraps of filament you have lying around! A full 1kg roll could print approximately 2500 beads, enough to make a chain 50m (164ft) long!

To connect pieces together, simply pinch the top end of one piece so that the opening becomes oval-shaped. Insert the oval end of the second piece inside and release. The pieces remain connected but can be separated again if needed. Create long chains or rings by adding as many pieces as you want.

Each piece takes approximately 5 minutes to print. It is, however, much more efficient to print multiple pieces sequentially! Setting up spiralized models to print “one at a time” takes a bit of planning as the pieces must be spaced and sequenced properly so that the hot end or gantry does not collide with the finished prints as it moves on to the next print. 

Make the bottom open by setting “bottom layers” to zero. Good build plate adhesion is essential, so ensure that your machine is well calibrated.

Similar Designs: 
Pop Bead Garland: https://social.thangs.com/m/513337 


Authentic Cuban Chain Print in Place, For Halloween Wearables, HalloweenWearable

This is the ONLY genuine Cuban Print in Place Chain you can get. Nothing else is even close. If you want your Costume to be OFF the CHAIN, you need this around your neck. Show them how cool you are, how far you are willing to go! 

halloweenwearable
halloweenwearables
halloween wearable
#halloweenwearable
#halloweenwearables


HALLOWEENWEARABLE

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Wearable halloween mask - Lizard - Moving jaw

Wearable halloween mask - Bird version 2

Wearable halloween mask - Bird version 1

Axe prop - Print in place!

Voroni Helmet.obj

Bat Glasses || HalloweenWearable

Costume Wing Mount - HalloweenWearable

Awooga Glasses || HalloweenWearable

Screw Crown Tight - HalloweenWearable

Modular Halloween Headband HalloweenWearable

Ghost Pop Beads

HalloweenWearable Mask - Male Version

WOLF MASK- HalloweenWearable

View 17 new models

Spider Halloween Glasses

Skull Pop Beads

View 91 new models